Hybrid Simulation
Mostrando 1-12 de 106 artigos, teses e dissertações.
-
1. Efficient Low-Complexity Optimized Channel Estimating Methods for OFDM-Based Low-Voltage Broadband Power Line Communication Systems
Abstract Broadband Power Line Communication (BB-PLC) technology enables data transmission for smart grid applications. Nevertheless, channel equalizers are required in the receiver to estimate and compensate for the nonlinear time-variant impulse response and noise interference effects introduced by the BB-PLC channel. In this paper, we append the Particle S
Journal of Microwaves, Optoelectronics and Electromagnetic Applications. Publicado em: 2022
-
2. FEM-DEM simulation of Uniaxial Compressive Strength (UCS) laboratory tests
Abstract Finite/discrete element methods (FDEM) are hybrid numerical models that use algorithms to analyze the transition from continuous to discontinuous. This type of formulation allows modeling physical laboratory tests with greater proximity to reality. This article proposes to simulate the average behavior of a uniaxial compression test campaign. The te
REM, Int. Eng. J.. Publicado em: 2020-12
-
3. Synthesis of Sparse Arrays Based On CIGA (Convex Improved Genetic Algorithm)
Abstract In this paper, a novel hybrid algorithm on beam pattern synthesis of sparse arrays is proposed, which aims at minimizing the peak sidelobe level (PSLL). Sparse arrays can provide higher spatial resolution and relatively lower sidelobe than general arrays, but it is necessary to solve the multi-constraint problem of nonconvex nonlinear. Thus, we prop
J. Microw. Optoelectron. Electromagn. Appl.. Publicado em: 2020-12
-
4. HYBRID SYSTEM SIMULATION TO SUPPLY HEATED AIR TO A SOLAR FOOD DRYER
ABSTRACT The intermittence of solar radiation, due to continuous rainy or cloudy days, is a limitation of simple and small solar dryers. These conditions often make them impossible to use. By including storage systems (thermal accumulation) and/or auxiliary energy sources, drying processes or dehydration can be conducted continuously, even during periods of
Eng. Agríc.. Publicado em: 2020-04
-
5. Synthesis of New Reconfigurable Limited Size FSS Structures Using an Improved Hybrid Particle Swarm Optimization
Abstract This paper describes a new design methodology for reconfigurable printed circuits with limited size, using an improved hybrid particle swarm optimization (HPSO) algorithm, reducing the search space by the definition of negative zones (NZ), regions where the swarm of particles should not travel. The proposed design methodology (HPSO-NZ) is used in th
J. Microw. Optoelectron. Electromagn. Appl.. Publicado em: 19/06/2019
-
6. Application of Short Fibers Reinforced Composites in Power Transmission Coupling
Abstract In this study the use of short glass, carbon and hybrid glass-carbon fibers reinforced polymeric composites in power transmission coupling is investigated. The presented work is generalized to thermoplastic and thermoset polymeric matrix composites. The effects of the constituents weight percentages, and average fibers length on the composite tensil
Lat. Am. j. solids struct.. Publicado em: 2017-10
-
7. Assessment of Percolation Threshold Simulation for Individual and Hybrid Nanocomposites of Carbon Nanotubes and Carbon Black
Modeling electrical conductivity of polymer composites with conductive fillers has great applicability to predict conductive materials behavior. In this study, the electrical behavior of simple and hybrid systems prepared from Carbon Black (CB) and Carbon Nanotubes (CNT) was studied. There have been few advances reported in the literature regarding the model
Mat. Res.. Publicado em: 18/09/2017
-
8. A Performance Evaluation of WLAN-Femtocell-LTE beyond the Capacity Crunch. Does Femtocell have to overcome WLAN or can they coexist in HetNets?
Abstract This paper originates from a practical experiment based on Mesh Networks. The promising results obtained from this experiment prompted us to discuss in greater depth whether Wireless Local Area Networks (WLAN) are still useful for current communications. This means that on the one hand femtocells can be defined as small base stations that use the sa
J. Microw. Optoelectron. Electromagn. Appl.. Publicado em: 2016-12
-
9. Parametric Modal Study and Optimization of the Floor Pan of a B-Segment Automotive Using a Hybrid Method of Taguchi and a Newly Developed MCDM Model
Abstract The floor pan is an important component that connects the front and rear segments of the automotive underbody structure. Global stiffness and NVH characteristics of BIW are highly dependent to shape, thickness and mass of the body panels and could be evaluated by modal characteristics of these panels. The feeling of solidness and comfort of passenge
Lat. Am. j. solids struct.. Publicado em: 2016-12
-
10. Simulation of Stress Concentration Problems in Laminated Plates by Quasi-Trefftz Finite Element Models
Abstract Hybrid quasi-Trefftz finite elements have been applied with success to the analysis of laminated plates. Two independent fields are approximated by linearly independent, hierarchical polynomials: the stress basis in the domain, adapted from Papkovitch-Neuber solution of Navier equations, and the displacement basis, defined on element surface. The st
Lat. Am. j. solids struct.. Publicado em: 2016-09
-
11. Ba-DOPED ZnO MATERIALS: A DFT SIMULATION TO INVESTIGATE THE DOPING EFFECT ON FERROELECTRICITY
ZnO is a semiconductor material largely employed in the development of several electronic and optical devices due to its unique electronic, optical, piezo-, ferroelectric and structural properties. This study evaluates the properties of Ba-doped wurtzite-ZnO using quantum mechanical simulations based on the Density Functional Theory (DFT) allied to hybrid fu
Quím. Nova. Publicado em: 2016-04
-
12. Finite element analysis of hybrid excitation axial flux machine for electric cars
This paper presents a FEM analysis of a hybrid excitation brushless axial flux machine (HEBAFM) for traction electric vehicle purposes in order to compare with the results from an analytical method used to determine the flux densities in each part of the machine. The magnetic quantities of the proposed topology were investigated in order to obtain a satisfac
J. Microw. Optoelectron. Electromagn. Appl.. Publicado em: 2014-12