Glass Carbon
Mostrando 1-12 de 124 artigos, teses e dissertações.
-
1. INFLUÊNCIA DA FORÇA IÔNICA NA ESTIMATIVA DE pKa POR MÉTODO VOLTAMÉTRICO
The voltammetry is an important analytical technique and also useful for pKa determination. It is a usual procedure of this technique to employ inert electrolyte concentration 100 times higher than redox compound concentration further a pH buffer. However, the ionic strength changes with the solution pH. In this work, we study the consequences of this proced
Quím. Nova. Publicado em: 2020-12
-
2. Evaluation of Carbon Nanotubes/Polyaniline Thin Films for Development of Electrochemical Sensors
Thin films of multiwalled carbon nanotubes/polyaniline nanocomposites (CNT/PAni) were synthesized through the liquid/liquid (L/L) interfacial route, deposited over glass substrates, and evaluated through cyclic voltammetry and amperometry as electrochemical sensor, using L-ascorbic acid as probe. Films with three different CNT/PAni ratios have been prepared.
J. Braz. Chem. Soc.. Publicado em: 2020-06
-
3. Potencial antimicrobiano de diferentes retentores intrarradiculares frente a Enterococcus faecalis: uma avaliação in vitro
Resumo Introdução O tratamento endodôntico tem como objetivo erradicar microrganismos bacterianos e fúngicos do canal radicular, ou pelo menos possibilitar sua redução para níveis compatíveis com a saúde do tecido perirradicular, uma vez que, após o tratamento endodôntico, colônias de microrganismos residuais podem estar presentes nos túbulos d
Rev. odontol. UNESP. Publicado em: 23/09/2019
-
4. PRODUCTION AND CHARACTERIZATION OF PRECIPITATED SILICA FROM PALM OIL MILL FLY ASH USING CO2 IMPREGNATION AND MECHANICAL FRAGMENTATION
ABSTRACT In this research, sol-gel precipitation using CO2 impregnation and mechanical fragmentation method was applied to produce precipitated silica from Palm Oil Mill Fly Ash (POMFA). Carbon dioxide (CO2) was used in order to reduce the cost of the process and to enable sodium hydroxide recovery. The precipitation process was done in a stirred temperature
Braz. J. Chem. Eng.. Publicado em: 15/07/2019
-
5. Microtensile bond strength of root canal dentin treated with adhesive and fiber-reinforced post systems
Abstract Nowadays, demand for esthetic restorations has risen considerably; thus, nonmetal esthetic posts made of either high-strength ceramics or reinforced resins, such as fiber-reinforced resin posts, have become more and more popular. Important characteristics of fiber-reinforced posts involve a modulus of elasticity similar to dentin and their ability t
Braz. oral res.. Publicado em: 01/07/2019
-
6. Influence of temperature on the adhesion of fibre reinforced polymers to timber surface
Resumo Os reforços de compósitos poliméricos com fibras de carbono (CFRP) e de vidro (GFRP) têm sido largamente usados em estruturas de madeira, onde eles podem estar expostos a condições adversas de temperatura. Para serem usados adequadamente, são necessárias informações sobre a sua adesão ao substrato. O objetivo desta pesquisa é avaliar a inf
Ambient. constr.. Publicado em: 10/06/2019
-
7. Size Effects on Fracture Parameters of High Alumina Refractories
The randomness of phase compositions and their distribution as well as the micro cracks and pores in refractories result in the dependence of mechanical properties on the sample size. In this work, the size effects on fracture parameters including bending strength, elastic modulus and fracture toughness of high alumina bricks were investigated by testing sam
Mat. Res.. Publicado em: 10/07/2018
-
8. Behavior of fiber reinforced mortar composites under impact load
Abstract This paper presents results of the experimental study on the behavior of plain and fiber reinforced cement mortars with different fibers under static and impact compressive load. Glass, polypropylene and carbon fibers were used in equal dosage by mass. The impact test was conducted using an impact tower with drop hammer, which represented the modif
Lat. Am. j. solids struct.. Publicado em: 26/04/2018
-
9. An Evaluation of the Dielectric Barrier Discharge Treatment on the Mechanical, Structural and Morphological Properties of Carbon Fibers
ABSTRACT: Carbon fibers (CFs) have been widely applied in the manufacture of polymeric composites. The mechanical properties of these composites depend on the adhesion in the matrix/CF interface. Since the CFs have poor adhesion properties, a surface treatment of the CFs becomes necessary. The plasma process used in this work was the dielectric barrier disch
J. Aerosp. Technol. Manag.. Publicado em: 29/03/2018
-
10. Lead hazard evaluation for cathode ray tube monitors in Brazil
Abstract Cathode ray tube (CRT) monitors are electronic equipment mainly made of glass, polymers and metals. These devices became obsolete because of emerging technologies such as LCD, LED and plasma; thus generating a huge stockpile of e-waste worldwide. In this CRT study, a natural leaching simulation (NBR10005) was performed to determine the toxicity of t
Braz. J. Chem. Eng.. Publicado em: 2018-01
-
11. Layer-by-Layer technique employed to construct multitask interfaces in polymer composites
Abstract The properties of glass fiber-reinforced polymer composites are closely related to the fiber-matrix interface. Interfacial treatments to improve mechanical properties are usually limited to enhance interfacial adhesion. In this work, Layer-by-Layer (LbL) technique was introduced to build a novel interface in polymer composites. Different numbers of
Polímeros. Publicado em: 2017-12
-
12. Mechanical Characterization of Basalt and Glass Fiber Epoxy Composite Tube
The application of basalt fibers are possible in many areas thanks to its multiple and good properties. It exhibits excellent resistance to alkalis, similar to glass fiber, at a much lower cost than carbon and aramid fibers. In the present paper, a comparative study on mechanical properties of basalt and E-glass fiber composites was performed. Results of app
Mat. Res.. Publicado em: 23/10/2017