Friction Models
Mostrando 1-12 de 49 artigos, teses e dissertações.
-
1. INFLUENCE OF ALBUMIN ON GUAVA PULP POWDER OBTAINED BY FOAM-MAT DRYING
ABSTRACT Guava is a fruit that stands out for its aroma, intense flavor, vitamins, and minerals. Its availability as a powdered food enhances its commercial applications. This study aimed to evaluate mathematical models for adsorption isotherms and determine the properties and flowability of guava pulp powder obtained by foam-mat drying. The models of GAB, B
Eng. Agríc.. Publicado em: 2020-06
-
2. Flexure Based Energy Dissipating Device in Self-Centering Braces
Abstract Self-centering braces, in the current stage of development can accommodate large deformation and force levels. However, there is still a need for improvement of the energy dissipation mechanisms commonly incorporated in these braces. Yield based energy dissipation systems can overcome some of the problems faced with friction-based devices, such as s
Lat. Am. j. solids struct.. Publicado em: 28/10/2019
-
3. Welfare Consequences of Persistent Climate Prediction Errors on Insurance Markets against Natural Hazards
Resumo Este artigo estuda as consequências da fricção entre dois grupos de agentes econômicos, com e sem expectativas racionais, sobre o bem-estar econômico em um mercado de seguro incompleto. Utilizando modelagem econométrica, validamos essa fricção empiricamente e testamos a existência de heterogeneidade adicional na probabilidade de pertencimento
Estud. Econ.. Publicado em: 10/07/2019
-
4. A Takagi-Sugeno fuzzy model for predicting the clean rock joints shear strength
Abstract It is well known that learning about the mechanical behavior of a fractured rock mass depends on the shear behavior of its discontinuities. Several studies have shown that the shear behavior of unfilled rock discontinuities depends on their boundary conditions, roughness characteristics and the properties of the joints walls. Currently, there are se
REM, Int. Eng. J.. Publicado em: 2019-06
-
5. Determination of Barreling of Aluminum Solid Cylinders During Cold Upsetting Using Genetic Algorithm
ABSTRACT This study presents Genetic Programming models for the formulation of barreling of aluminum solid cylinders during cold upsetting based on experimental results. The maximum and minimum radii of the barreled cylinders having different aspect ratio (d/h= 0.5, 1.0 and 2.0) were measured for various frictional conditions (m=0.1-0.4). The change in radii
Matéria (Rio J.). Publicado em: 20/05/2019
-
6. Numerical simulation of bolted connections
Abstract This article presents the modeling of a complete bolted connection based on a model with one bolt connecting two or three plates. Initially, the behavior of this model with one bolt is analyzed by comparing it with existing bibliography for 3 different types of applied load: tension, shear and a combination of these two. This model includes all nece
Lat. Am. j. solids struct.. Publicado em: 22/10/2018
-
7. Manipulation of Glassy State in Amorphous Selenium by Low-temperature Internal Friction Measurements
We have studied the thickness and quench-rate dependent internal friction of amorphous selenium (a-Se) thin films deposited at room temperature. The internal friction of a-Se films exhibit a temperature independent plateau below 1 K followed by a broad maximum at 10 K. The plateau, which is seen in almost all amorphous solids, is caused by dissipation by two
Mat. Res.. Publicado em: 07/06/2018
-
8. Comportamiento reológico del aluminio AA6061 por efecto de las transformaciones de fase activadas térmicamente
ABSTRACT Aluminum alloys at room temperature not experience significant rheological behavior due to its coherent microstructural order, and its high compactness. However, the increase of the temperature generates stress fields, and thereby deformations, that alter the microstructural equilibrium, manifesting the rheological behavior as consequence of the int
Matéria (Rio J.). Publicado em: 22/06/2017
-
9. Glass Microbeads in Analog Models of Thrust Wedges
ABSTRACT Glass microbeads are frequently used in analog physical modeling to simulate weak detachment zones but have been neglected in models of thrust wedges. Microbeads differ from quartz sand in grain shape and in low angle of internal friction. In this study, we compared the structural characteristics of microbeads and sand wedges. To obtain a better pic
An. Acad. Bras. Ciênc.. Publicado em: 2017-03
-
10. Sensitivity analysis and parameter estimation of heat transfer and material flow models in friction stir welding
Although numerical models of heat transfer and material flow have contributed to understand the underlying mechanisms of friction stir welding (FSW), there are certain input model parameters that can not be easily determined. Thus, the model predictions do not always agree with experimental results. In this work, sensitivity analysis and parameter estimation
Mat. Res.. Publicado em: 08/11/2013
-
11. On the evaluation of linear and non-linear models using DNS data of turbulent channel flows
In this paper, a priori and a posteriori analyses of algebraic linear and non-linear models are carried out in order to compare their ability to predict near wall turbulent flows. Tests were done using data from a direct numerical simulation (DNS) of a plane channel flow for three Reynolds numbers, based on the friction velocity, Reτ = 180, Reτ = 395 and R
J. Braz. Soc. Mech. Sci. & Eng.. Publicado em: 2012-12
-
12. Análise numérica do comportamento de blocos sobre quatro estacas com cálice parcialmente embutido : estudos de casos reais / Numerical analysis of the behavior of four-pile caps of partially embedded socket : studies of real cases
There is a lack of knowledge about pile caps. Studies concerning these elements are limited to the case of pile-caps subjected to centered forces without connection elements. In this context this research aims to clarify some doubts about the behavior of pile caps under centered forces and bending moment. The behavior of four pile-caps with partially embedde
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 06/12/2011