Friction Materials
Mostrando 13-24 de 97 artigos, teses e dissertações.
-
13. Head loss in laser-perforated thin-walled polyethylene pipes for irrigation
RESUMO Para reduzir custos fixos e operacionais em sistemas de irrigação pressurizados são produzidos tubos de polietileno com pequena espessura de parede, com orifícios de descarga perfurados a laser, que operam a baixas pressões (até 100 kPa). A caracterização hidráulica desses materiais é essencial para o dimensionamento dos sistemas de irrigaç
Rev. bras. eng. agríc. ambient.. Publicado em: 06/05/2019
-
14. Integrated Experimental Approach for Alloying of Surface Layer Ti6Al4V+B4C Metal Matrix Composites using Laser Treatment
Surface engineering applications have brought the titanium and its alloys into the limelight in the manufacturing industries such as the aerospace, automobile, marine, chemical processing industry, nuclear power and biomedical. Despite the growths experienced in the use of this material, it is plagued with poor wear behaviour, especially when in contact with
Mat. Res.. Publicado em: 17/01/2019
-
15. The Contribution of Mechanical Spectroscopy to Understanding Grain Boundary Sliding
This review paper shows that grain boundary sliding (GBS) is a general phenomenon occurring in all classes of inorganic materials: ceramics, metals and composite materials. The occurrence of relaxations attributed to GBS is also quite general and therefore the mechanical spectroscopy constitutes a sensitive and universal technique to study such phenomenon. G
Mat. Res.. Publicado em: 25/10/2018
-
16. Influencia de la temperatura en ensayos de arrancamiento sobre diferentes sistemas epoxi-acero de uso en conectores de ductos flexibles
ABSTRACT In the offshore oil fields located in deep and ultra-deep waters they are used flexible pipes. In many cases inside these pipes, the hydrocarbons are transported at elevated temperatures. At the ends of the flexible pipes are installed end fittings, these are the connection with sea platforms and different subsea systems. In the assembly of end fitt
Matéria (Rio J.). Publicado em: 19/07/2018
-
17. Estudio de propiedades mecánicas locales de uniones soldadas por fricción agitación (FSW) en AA6061-T6 mediante Small Punch Test (SPT)
ABSTRACT Friction Stir Welding (FSW) is a solid state process that has reach a strong technological impact in welding of aluminum alloys. Among its advantages, it may include the ability of joining materials that are difficult to weld by fusion. In welding of heat treatable aluminum alloys, some degradation in metallurgical properties is observed, so welds s
Matéria (Rio J.). Publicado em: 19/07/2018
-
18. Comportamiento frente a la corrosión de uniones soldadas por fricción agitación de AA7075-T651: Evaluación galvánica
ABSTRACT Friction Stir Welding (FSW) is a novel solid-phase welding process, which has proved to have a great potential for the realization of welded joints in materials with poor weldability such as heat-treatable aluminum alloys. The aerospace industry has incorporated this process for the manufacture of structural elements, using known high strength alloy
Matéria (Rio J.). Publicado em: 19/07/2018
-
19. Manipulation of Glassy State in Amorphous Selenium by Low-temperature Internal Friction Measurements
We have studied the thickness and quench-rate dependent internal friction of amorphous selenium (a-Se) thin films deposited at room temperature. The internal friction of a-Se films exhibit a temperature independent plateau below 1 K followed by a broad maximum at 10 K. The plateau, which is seen in almost all amorphous solids, is caused by dissipation by two
Mat. Res.. Publicado em: 07/06/2018
-
20. Measurement of Strain-Amplitude Dependent Internal Friction with Torsion Pendulum and Vibration Reed Methods
In the traditional standard of internal friction measurement the torsion pendulum and vibration reed were preferentially recommended where the issue of strain amplitude dependence of internal friction was not concerned. To more precisely measure the internal friction and modulus at various strain amplitude, in this paper the strain amplitude dependence of in
Mat. Res.. Publicado em: 28/05/2018
-
21. Effect of Heat Input on the Mechanical Behaviour of Al-Cu FSW Lap Joints
Dissimilar Al-Cu joints are desirable due to the combination of the good electrical and thermal properties of copper with the economic advantages of aluminium. However, different chemical, mechanical and thermal properties turn dissimilar welding into a challenge with traditional fusion welding techniques. Friction stir welding appears to be a good alternati
Mat. Res.. Publicado em: 28/05/2018
-
22. An Overview of Research into Low Internal Friction Optical Coatings by the Gravitational Wave Detection Community
The direct detection of gravitational waves by ground-based interferometric gravitational wave detectors in recent years has opened a new window of the universe, allowing the astrophysical observations of previously unexplored phenomena, such as the collisions of black holes and neutron stars. However, small thermodynamic fluctuations of the density of the t
Mat. Res.. Publicado em: 24/05/2018
-
23. Thermomechanical Modelling of FSW Process Using a Cylindrical Tool in an Aluminum Alloy Alclad AA 2024-T3
The Friction Stir Welding Process (FSW/P) is an innovative technique to join metals using the plasticity, not occurring the melting. It was initially applied in aluminum alloys, but recently it has been extended to other materials, for example, copper, steel alloys, polimers and others. In this work it is analyzed the thermo mechanical modelling of the energ
Mat. Res.. Publicado em: 07/05/2018
-
24. Investigation on Friction and Wear Properties of High-Temperature Bearing Steel 9Cr18Mo
This paper presented a study of friction and wear on 9Cr18Mo when rubbed against other materials (steel-304, steel-440C, steel-GCr15 or silicon nitride ceramic ball) at high temperature conditions. Friction and wear tests were carried out with universal a friction and wear testing machine. The wear morphology was analyzed by a Nanovea three-dimensional profi
Mat. Res.. Publicado em: 05/04/2018