Fractographic Analysis
Mostrando 1-12 de 16 artigos, teses e dissertações.
-
1. Reinforcement of Polyester with Renewable Ramie Fibers
Ramie (Boehmeria nivea) fiber is one of several lignocellulosic fibers with superior strength, but the least investigated, particularly as reinforcement in strong, tough polymeric composites. This paper presents mechanical properties for polyester reinforced with aligned ramie fibers up to 30% by volume. It was found that adding 30 vol% of ramie fibers incre
Mat. Res.. Publicado em: 11/05/2017
-
2. Normalizing effect on fatigue crack propagation at the heat-affected zone of AISI 4140 steel shielded metal arc weldings
The fractography and mechanical behaviour of fatigue crack propagation in the heat-affected zone (HAZ) of AISI 4140 steel welded using the shielded metal arc process was analysed. Different austenitic grain size was obtained by normalizing performed at 1200 °C for 5 and 10 hours after welding. Three point bending fatigue tests on pre-cracked specimens along
Mat. Res.. Publicado em: 02/04/2013
-
3. Fractographic analysis of tensile failures of aerospace grade composites
This paper describes fractographic features observed in aerospace composites failed under tensile loads. Unidirectional Carbon Fibre Reinforced Plastic (UD CFRP) and Unidirectional Glass Fibre Reinforced Plastic (UD GFRP) composite specimens were fabricated and tested in tension. The morphology of fractured surfaces was studied at various locations to identi
Mat. Res.. Publicado em: 23/10/2012
-
4. Crack propagation under constant amplitude loading based on an energetic parameters and fractographic analysis
The crack propagation behavior in a 2024 T351 Aluminum Alloy under constant amplitude loading has been studied. This study is complemented by quantitative microfractographic observations and energetic analysis. The obtained results under constant amplitude fatigue tests show that different crack propagation stages can be identified and correlated with the ev
Materials Research. Publicado em: 03/07/2012
-
5. Fragilização por hidrogênio de parafusos cementados / Hydrogen embrittlement of carburized bolts
The main aim of this work is to investigate the effects on hydrogen embrittlement of bolts due to acid pickling, baking, and strip processes performed during zinc plating. Carburized bolts type "hexagon flange head tapping screws", with 6 mm of diameter and 16 mm of thread length were organized into 39 different groups. Acid pickling was evaluated using volu
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 28/07/2011
-
6. Efeitos do revenimento realizado a baixa temperatura na resistência ao impacto em aços carbono e ligados temperados
This work has as main objective the determination of mechanical behavior, specially the impact resistance of martensitic structures based on carbon and on alloyed steels. The main concern is the response of these alloys when tempering at low temperatures (below 180C). Heat treatments were performed by quenching in water and oil in order to determine the seve
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 15/02/2011
-
7. Development and characterization of composite materials for production of composite risers by filament winding
Industry has been challenged to provide riser systems which are more cost effective and which can fill the technology gaps with respect to water depth, riser diameter and high temperatures left open by flexibles, steel catenary risers (SCRs) and hybrid risers. Composite materials present advantages over conventional steel risers because composite materials a
Materials Research. Publicado em: 26/08/2011
-
8. Estudo da causa de falhas dos aços inoxidáveis austeníticos utilizados em implantes ortopédicos
Given the variety of metallic materials used in orthopedic implants, the austenitic stainless steel type 316L and F138 have been widely used in Brazil as biocompatible material. Used by the public health, mainly due to it is low cost of manufacture compared to other materials, and because of the good combination of properties of which can be highlighted: The
Publicado em: 2010
-
9. Fractographic analysis, accuracy of fit and impact strength of acrylic resin
This study evaluated accuracy of fit, impact strength, types and morphology of fractures of a microwave acrylic resin polymerized with a cycle alternative to that recommended by the manufacturer. Onda Cryl was polymerized according to the manufacturer's instructions (MC), 3 min at 360 W, 4-min pause, and 3 min at 810 W; and with an alternative cycle (AC) of
Brazilian Oral Research. Publicado em: 2008-12
-
10. Influência dos tratamentos térmicos e tratamentos criogênicos na tenacidade do aço rápido AISI M2. / Influence of the heat treatments and cryogenic treatments on the toughness of the AISI M2 high speed steel.
In this work the toughness of the AISI M2 high speed steel heat treated by conventional and cryogenic routes has been evaluated. The toughness was evaluated through un-notched impact samples and 3 points bending cylindrical samples. The heat treatments were carried out in a vacuum furnace using nitrogen quenching with 6 bar of pressure. The conventional rout
Publicado em: 2008
-
11. Propriedades de fadiga de parafusos de alta resistencia mecanica / Fatigue properties of hith strengh bolts
High strength bolts, class ISO 10.9, were manufactured with two different steels in order to investigate the influence of tempering temperature, the sequence of manufacture process (threads rolled before and after heat treatment), and the inclusions amount contained in steels, in the bolt fatigue behavior and also what criterion of fatigue failure existent i
Publicado em: 2008
-
12. Estudo da inferência de carregamento em histórias de vôos simulados na liga de Al aeronáutico SAE-AMS 7475 T7351 / Loading study of inference in a simulated flights history using an SAE-AMS 7475 T7351 aluminum alloy.
The loading inference and the fractographic reconstruction of fatigue crack propagation rate in simulated flight stories, as Twist, mini-Twist, Falstaff and mini-Falstaff were investigated in this work. The studied material was an aluminum alloy SAE-AMS 7475 T7351. Tensile and hardness tests were carried out in order to determine mechanical properties, as we
Publicado em: 2007