Fe Al Alloys
Mostrando 25-36 de 53 artigos, teses e dissertações.
-
25. Modelagem analítica e numérica da solidificação de ligas binárias : análise de fatores de influência / Analytical and numerical modeling of solidification of binary alloys : analysis of influential factors
Em um estudo completo da solidificação, a transferência de calor e a transferência de massa são duas componentes que devem ser analisadas. Este trabalho inicia-se com o levantamento de fatores que podem influenciar a modelagem matemática da transferência de calor em sistemas de solidificação unidirecional. Dados experimentais, obtidos através da so
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 31/01/2012
-
26. Evaluation of erosion-corrosion resistance in Fe-Mn-Al austenitic steels
In this paper, the effects of Mn and Al against corrosion/errosion resistance of three samples of the Fe-Mn-Al austenitic alloys are evaluated. The samples have composition Fe-(4,9 ~ 11,0 wt. (%)) Al-(17,49 ~ 34,3 wt. (%)) Mn-(0,43 ~ 1,25 wt. (%))C, those were prepared in an induction furnace from high purity materials. The alloys were evaluated in a compose
Mat. Res.. Publicado em: 18/12/2012
-
27. Study of the Al-Si-X system by different cooling rates and heat treatment
The solidification behavior of the Al-12.6% Si (A1), the hypereutectic Al-20%Si (A2) and the Al-20%Si-1.5% Fe-0.5%Mn (A3) (in wt. (%)) alloys, at different cooling rates is reported and discussed. The cooling rates ranged between 0.93 °C/s and 190 °C/s when cast in sand and copper wedge-shaped molds, respectively. A spheroidization heat treatment was carri
Mat. Res.. Publicado em: 30/08/2012
-
28. Termodinâmica de primeiros princípios aplicada a ligas de metais de transição / Thermodynamics of first principles applied to alloys of transition metals
A termodinâmica computacional é uma ferramenta capaz de fornecer informações básicas sobre soluções e concentração de seus constituintes, em um dado sistema complexo a uma certa temperatura e pressão. Nos últimos anos, a união entre a teoria do funcional da densidade e a termodinâmica computacional tem renovado o estudo dos materiais intermetál
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 14/10/2011
-
29. Finite element simulations of Ti6Al4V titanium alloy machining to assess material model parameters of the Johnson-Cook constitutive equation
The machining of titanium alloys poses several inherent difficulties owing to their unique mechanical properties and cutting characteristics. Finite element (FE) simulations have reduced the burden of extensive experimental trials in understanding the deformation behavior and optimize the cutting process. The FE code relies on the qualitative nature of input
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2011-06
-
30. Processamento e caracterização de aluminetos de ferro obtidos a partir de matéria-prima reciclada. / Processing and characterization of iron aluminides made from recycled raw material.
Os Aluminetos de Ferro tem, dentre muitas características predominantes, excelente resistência à corrosão a altas temperaturas devido à formação de uma camada protetora de alumina que favorece a sua aplicação em ambientes agressivos. Este trabalho tem por objetivo estudar a produção de ligas a partir de matéria-prima reciclada e a cinética de ox
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 04/11/2010
-
31. Caractericação da microestrutura de solidificação de ligas Al-Fe e correlação com propriedades mecânicas / Characterização solidification microstructures of Al-Fe alloys and correlation with medchanical properties
Foram realizados estudos em estruturas de solidificação de três ligas hipoeutéticas Al-Fe, as quais foram solidificadas direcionalmente sob condições transitórias de extração de calor. Durante a solidificação fora do equilíbrio de fundidos, uma gama de taxas de resfriamento pode ocorrer da superfície ao centro da peça, o que pode causar a forma
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 10/08/2010
-
32. Corrosão-erosão da liga Cu10Ni-3Al-1, 3Fe em presença de íons cloreto, sulfeto e sulfato. / Corrosion-erosion of Cu10Ni-3Al-1, 3Fe alloy in the solution with chloride, sulfide or sulphate ions.
O presente trabalho teve como objetivos determinar a resistência à corrosão e as propriedades mecânicas da liga Cu10Ni-3Al-1,3Fe, nas condições solubilizada e envelhecida a 550°C. Foi também objetivo do trabalho identificar a microestrutura nestas condições de tratamento térmico. As propriedades mecânicas foram avaliadas a partir de ensaios de tr
Publicado em: 2010
-
33. Obtenção e evolução da fase icosaedral quasicristalina em ligas Al-Cu-Fe e Al-Cu-Fe-B por Melt-Spinnin / OBTAINING AND EVOLUTION OF PHASE ICOSAHEDRAL QUASICRISTALINA IN ALLOYS Al-Cu-Fe AND Al-Cu-Fe-B BY MELT-SPINNING
Melt spinnng processing is one of the most common processes to obtaining quasicrystaline structures. This is because of the fast cooling rate it imposes on the system, favoring such type of structure. This work deals with the production of quasycristaline phases (Al60Cu27,5Fe12,5 e Al57Cu27,5Fe12,5B3) via melt-spinning. The alloys were initially cast via ind
Publicado em: 2009
-
34. Oxidation behavior of FeCr and FeCrY alloys coated with an aluminium based paint
A variety of metallic components rely on properties that are specific to the alloy and its surface. Coatings have been extensively used to protect metallic surfaces from the aggressive effects of the environment to which it is exposed. In this investigation, the high temperature oxidation behavior of a FeCr and a FeCrY alloy coated with an aluminium based pa
Materials Research. Publicado em: 2008-09
-
35. Processing, microstructural characterization and mechanical properties evaluation of the Al92Fe3Cr2Mn3 alloy / Processamento, caracterização microestrutural e avaliação das propriedades mecanicas da liga Al92Fe3Cr2Mn3
Aluminum alloys having a particle dispersion in nanometric scale, which present elevated values of mechanical strength at both ambient and high temperatures have been studied for some time. These alloys are known for presenting icosahedral particles embedded in an α-Al matrix and they are called nanoquasicrystalline alloys, having large thermal stabilit
Publicado em: 2008
-
36. Nucleation and growth of austenite/VC eutectic in alloys of the Fe-V-C system. / Nucleação e crescimento do eutético austenita/VC em ligas do sistema Fe-V-C.
The three most commercially important families of alloys for the foundry industry show the formation of faceted/non-faceted eutectics type during solidification: cast irons with graphite (austenite/graphite eutectic), white cast irons (austenite/carbide eutectic) and Al-Si alloys (alfa/silicon eutectic). In the case of white cast irons, the eutectic carbide
Publicado em: 2008