Eutectic Alloy
Mostrando 1-12 de 46 artigos, teses e dissertações.
-
1. Tensile and fatigue properties, machinability and machined surface roughness of Al-Si-Cu alloys
ABSTRACT In this paper, the aim was to determine if ASC91 (9 % Al, 1 % Cu) could be replaced with ASC73 (7 % Al, 3 % Cu) aluminium alloy, with presumably improved machinability due to lower silicon content (9 to 7 %) and retained mechanical properties due to a higher copper content (1 to 3 %). The test samples were excised from cylinder heads produced by the
Matéria (Rio J.). Publicado em: 16/09/2019
-
2. Effects of Macrosegregation and Microstructure on the Corrosion Resistance and Hardness of a Directionally Solidified Zn-5.0wt.%Mg Alloy
This study aims to analyze the influence of macrosegregation on microstructure evolution, and of microstructure length scale on the corrosion resistance of a Zn-5.0wt.%Mg alloy casting. The analyzed samples were taken along the length of castings unidirectionally solidified in unsteady state conditions of heat extraction. Microstructure characterization, mic
Mat. Res.. Publicado em: 05/09/2019
-
3. Effect of Extrusion and Heat Treatment on Microstructure and Mechanical Properties of Hypereutectic A390-0.3wt%Nd Alloy
An hypereutectic aluminium alloy with a composition of 16-18wt%Si, 4-5wt%Cu, 0.45-0.65wt%Mg, 0.3wt%Nd and Al balance (A390-0.3wt%Nd alloy) was processed by extrusion and aging at 200ºC for 10 hours. The effect of the thermomechanical processing and heat treatment on microstructure and mechanical properties was investigated for A390-0.3wt%Nd alloy. It was sh
Mat. Res.. Publicado em: 10/06/2019
-
4. Mejora de la resistencia al desgaste abrasivo de un revestimiento Fe-Cr-Mn-C mediante la adición de V
ABSTRACT The aim of this work is to increase the abrasive wear resistance of a coating, applied on plates of AISI 1020 carbon steel, using tubular coated electrodes with the Fe-Cr-Mn-C alloy system. In order to achieve this increase, V was added to the alloy system. The resulting coating were studied using optical microscopy (MO), X-ray diffraction and micro
Matéria (Rio J.). Publicado em: 20/05/2019
-
5. Effects of Forming Processes on Microstructures and Mechanical Properties of A356 Aluminum Alloy Prepared by Self-inoculation Method
Semisolid slurry of A356 aluminum alloy was prepared by Self-Inoculation Method (SIM), and the microstructures and solidification behavior of rheo-forming process in different forming processes were researched. The results indicate that semisolid slurry of A356 aluminum alloy can be prepared by Self-Inoculation Method at 600ºC. Primary α-Al particles with
Mat. Res.. Publicado em: 11/04/2019
-
6. Relationship Between Aluminum-Rich/Intermetallic Phases and Microhardness of a Horizontally Solidified AlSiMgFe Alloy
An experimental study with an A356-AlSiMgFe alloy was developed to evaluate the microhardness performance in the microstructure resulting of an unsteady-state horizontal solidification process. The Al-7wt%Si-0.3wt%Mg-0.15wt%Fe alloy was elaborated and directionally solidified in a water-cooled horizontal solidification device. In order to experimentally dete
Mat. Res.. Publicado em: 23/11/2018
-
7. Evolución microestructural durante el envejecimiento a alta temperatura de una aleación 35Ni-25Cr-Nb
ABSTRACT The dendritic-type microstructure of the 35Ni-25Cr-Nb alloy, in the as-cast condition, consists of an austenitic matrix and two types of eutectic primary carbides; Nb-rich MC type and Cr-rich M23C6 type both presents in interdendritic edges and grain boundaries. During aging at 800ºC for different times, M23C6 type secondary carbides precipitate in
Matéria (Rio J.). Publicado em: 19/07/2018
-
8. An Experimental Study of the Solidification Thermal Parameters Influence upon Microstructure and Mechanical Properties of Al-Si-Cu Alloys
Metals solidification involves the transformation of the molten metal back into the solid state. Solidification structures impact heavily on the final product's characteristics. The microstructure effects on metallic alloys properties have been highlighted in various studies and particularly the dendrite arm spacing influence upon the mechanical properties s
Mat. Res.. Publicado em: 18/06/2018
-
9. Study of Mechanical and Wear Behaviour of Hyper-Eutectic Al-Si Automotive Alloy Through Fe, Ni and Cr Addition
Effect of Fe, Ni and Cr addition on the wear behavior of hyper-eutectic Al-Si automotive alloy has been studied. Dry sliding wear tests have been conducted using pin-on-disc wear testing machine under normal loads of 20N and constant sliding speed of 0.64 ms-1. Influence of Fe addition to the base alloy increases the wear rate due to the formation of needle
Mat. Res.. Publicado em: 11/06/2018
-
10. Solution Treatment Behaviors of 6061 Aluminum Alloy Prepared by Powder Thixoforming
Powder thixoforming (PTF) was a promising processing technology that can be used to fabricate high strength particle reinforced aluminum matrix composites, and a pioneer 6061 matrix alloy was fabricated utilizing PTF to investigate its solution treatment behaviors. A comparison study with traditional permanent mold cast (PMC) 6061 alloy disclosed that PTF al
Mat. Res.. Publicado em: 07/05/2018
-
11. Transient Unidirectional Solidification, Microstructure and Intermetallics in Sn-Ni Alloys
The present research work examines the microstructural arrangements formed during the transient solidification of eutectic Sn-0.2wt.%Ni and hypereutectic Sn-0.5wt.%Ni alloys. Also, it examines their respective correlations with solidification thermal parameters: eutectic growth rate (VE) and eutectic cooling rate (ṪE); length scales of matrix and eutectic
Mat. Res.. Publicado em: 12/04/2018
-
12. Microstructural evolution and mechanical properties of Sn-Bi-Cu ternary eutectic alloy produced by directional solidification
Sn-36Bi-22Cu (wt.%) ternary eutectic alloy was prepared using vacuum melting furnace and casting furnace. The samples were directionally solidified upwards solidification rate varying from 8.3 to 166 µm/s and at a constant temperature gradient (4.2 K/mm) in a Bridgman-type directional solidification furnace. The composition analysis of the phases and the in
Mat. Res.. Publicado em: 05/02/2018