Cutting Force
Mostrando 1-12 de 56 artigos, teses e dissertações.
-
1. Influência do material da ferramenta de corte sobre a usinabilidade do aço ABNT 4340 no torneamento
RESUMO No presente trabalho procurou-se compreender os fenômenos associados à usinagem do aço ABNT 4340 utilizando ferramentas de corte de metal duro e cermet, ambas com geometria do quebra-cavaco para usinagem leve (LP) e média (MP). Nesse sentido, analisou-se a influência da variação do avanço, quebracavaco e o material da ferramenta de corte nos p
Matéria (Rio J.). Publicado em: 16/09/2019
-
2. Tensile and fatigue properties, machinability and machined surface roughness of Al-Si-Cu alloys
ABSTRACT In this paper, the aim was to determine if ASC91 (9 % Al, 1 % Cu) could be replaced with ASC73 (7 % Al, 3 % Cu) aluminium alloy, with presumably improved machinability due to lower silicon content (9 to 7 %) and retained mechanical properties due to a higher copper content (1 to 3 %). The test samples were excised from cylinder heads produced by the
Matéria (Rio J.). Publicado em: 16/09/2019
-
3. Influência do material da ferramenta de corte sobre a usinabilidade do aço ABNT 4340 no torneamento
RESUMO No presente trabalho procurou-se compreender os fenômenos associados à usinagem do aço ABNT 4340 utilizando ferramentas de corte de metal duro e cermet, ambas com geometria do quebra-cavaco para usinagem leve (LP) e média (MP). Nesse sentido, analisou-se a influência da variação do avanço, quebracavaco e o material da ferramenta de corte nos p
Matéria (Rio J.). Publicado em: 20/05/2019
-
4. Surface Integrity Analisys in the Hard Turning of Cemented Steel AISI 4317
This work was based on the surface integrity analysis of hardened steel, AISI 4317 case carburized, quenched and tempered with 58 HRC, obtained by a turning operation executed with CBN (cubic boron nitride) tool, varying three basic cutting parameters (cutting speed, feed rate and cutting depth). The surface integrity characterization was conducted analyzing
Mat. Res.. Publicado em: 26/07/2018
-
5. Simulation of the mechanical process of gypsum cutting with picks
Abstract Several research works have been done to assess the effect of the cutting depth on the cutting forces when using picks. In this case, the cutting tests need im-portant equipment to cut rocks, to register the cutting force and to determine the cutting force value. The purpose of this research work is to simulate the laboratory rock cutting tests to d
REM, Int. Eng. J.. Publicado em: 2018-07
-
6. Machinability Evaluation in Hard Milling of AISI D2 Steel
Milling of hardened steel components provides considerable benefits in terms of reduced manufacturing cost and time compared to traditional machining. Temperature variation in milling is an important factor affecting the wear of cutting tools. The poor selection of milling parameters may cause excessive tool wear and increased work surface roughness. Hence,
Mat. Res.. Publicado em: 01/03/2016
-
7. Evaluation of different methods of cooling-lubrication in cylindrical grinding of advanced ceramic dip
The current work presents a study of alternative methods of cooling-lubrication for the external plunge grinding of advanced ceramics using diamond wheels. These two alternative methods, which are intended to reduce cutting fluid expenses, are commonly referred to as the optimized cooling-lubrication method and minimal quantity of lubrication (MQL). The tech
Mat. Res.. Publicado em: 30/09/2014
-
8. Cutting force response in milling of Inconel: analysis by wavelet and Hilbert-Huang Transforms
We study the milling process of Inconel. By continuously increasing the cutting depth we follow the system response and appearance of oscillations of larger amplitude. The cutting force amplitude and frequency analysis has been done by means of wavelets and Hilbert-Huang transform. We report that in our system the force oscillations are closely related to th
Lat. Am. j. solids struct.. Publicado em: 2013-01
-
9. Emprego de ferramentas estatísticas para avaliação da usinabilidade de ligas de alumínio
The main objective of the present work is to study the effect of the input variables: mechanical properties of the workpiece (tensile strength, hardness and elongation) and cutting conditions (cutting speed, feed rate, depth of cut and lubri-cooling system) over the output variables: cutting forces, power consumption, cutting temperature, surface roughness (
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 28/05/2012
-
10. Influência do teor de silício na usinabilidade da liga de alumínio 6351 - avaliada através de força de corte e acabamento superficial / Influence of the silicon content in the machinability of the 6351 aluminium alloy analysed through cutting force and surface finish
The aim of this work is to study the effect of silicon content in the machinability of CBAs (Compania Brasileira de Aluminio) 6351 aluminum alloy measured through cutting force and surface finish. In a first moment the effect of depth of cut (ap), cutting speed (vc), feed rate (f) and silicon content (% Si) on the machinability were investigated. The machini
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 14/03/2012
-
11. Estudo da influência da força de corte em usinagem a verde nas propriedades mecânicas de cerâmicas sinterizadas / Influence of the cutting force of green machining on the mechanical properties of sintered ceramics
The present study deals with the measurement forces of green machining ceramics and their correlation with the mechanical properties after sintering. The green machining is employed in crude compacts either to check raw formats without compromising the extreme dimensional accuracy or to obtain a preform prior to finish machining after sintering, extensively
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 13/01/2012
-
12. Modelling and analysis of cutting force and surface roughness in milling operation using TSK-type fuzzy rules
The present paper discusses on development of fuzzy rule based models (FRBMs) for predicting cutting force and surface roughness in milling operation. The models use TakagiSugeno-Kang-type (TSK-type) fuzzy rule to study the effect of four (input) cutting parameters (cutting speed, feed rate, radial depth of cut and axial depth of cut) on outputs (cutting for
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2012-03