Copper Alloy
Mostrando 1-12 de 63 artigos, teses e dissertações.
-
1. Glass Formation of Null-Matrix Cu-Hf-(Zr, Ti) Alloys
An approach following the null-matrix, Ti/Zr ratio of 2.08, for neutron diffraction was used to calculate the glass formation in Cu-Ti-(Hf,Zr) alloys. The Cu55Zr14.6Ti30.4, Cu61.48Hf18.52Zr6.48Ti13.52, Cu58.1Hf16.9Zr8.1Ti16.9 and Cu52.46Hf14.2Zr10.8Ti22.54 compositions (at. %), were calculated and prepared by argon arc melting. Copper die suction casting was
Mat. Res.. Publicado em: 13/01/2020
-
2. Effect of Scanning Speed on the Surface Roughness of Laser Metal Deposited Copper on Titanium Alloy
This paper reports on the effect of scanning speed on the laser deposited Cu on titanium alloy substrate. The experiments were conducted by varying the scanning speed from 0.3 m/min to 1.2 m/min while the laser power, the powder feed rate and the gas flow rate were kept constant. The laser deposited Cu were characterized through the evolving microstructure a
Mat. Res.. Publicado em: 20/12/2019
-
3. Phase Separation and Development of the Microstructure for Stainless Steel to Copper Alloy Weld Joints Using a Fiber Laser
ABSTRACT Stainless steel and copper alloys joints are often applied in aerospace, marine and power industries where both high thermal and electrical conductivity (Cu) and corrosion resistance (steel) are required. In the aerospace industry, in particular for the combustion chamber of rocket engines, copper and steel combinations offer perfect materials selec
J. Aerosp. Technol. Manag.. Publicado em: 10/10/2019
-
4. Tensile and fatigue properties, machinability and machined surface roughness of Al-Si-Cu alloys
ABSTRACT In this paper, the aim was to determine if ASC91 (9 % Al, 1 % Cu) could be replaced with ASC73 (7 % Al, 3 % Cu) aluminium alloy, with presumably improved machinability due to lower silicon content (9 to 7 %) and retained mechanical properties due to a higher copper content (1 to 3 %). The test samples were excised from cylinder heads produced by the
Matéria (Rio J.). Publicado em: 16/09/2019
-
5. Produção e caracterização de revestimentos de ligas metálicas Cu-Sn em banho eletrolítico contendo glicina: ensaios preliminares
RESUMO Os problemas relacionados à corrosão são frequentes, podendo ocorrer nas mais variadas áreas, tais como, nas indústrias química, petroquímica, naval, de construção civil e automobilística, dentre outros setores produtivos. Portanto, métodos para prevenir a corrosão devem ser empregados para evitar a perda de materiais e o uso de revestimen
Matéria (Rio J.). Publicado em: 16/09/2019
-
6. Influence of Directional Solidification on the Mechanical Properties of Cu-Al-Be-Nb-Ni Alloy
Copper-based polycrystalline shape memory alloys (SMAs) have limitations for many practical applications due to their low superelasticity and low ductility. In order to overcome this situation, in recent years, the production of copper-based SMAs by directional solidification process has attracted the interest of many researches. In this sense, the present w
Mat. Res.. Publicado em: 05/09/2019
-
7. Performance and Surface Integrity of Wire Electrical Discharge Machining of Thin Ti6al4v Plate Using Coated and Uncoated Wires
Wire Electrical Discharge Machining (WEDM) is one of the most important production technologies to manufacture very accurate small components and tools on any electrical conductive material. Titanium and its alloys have been widely used in automobile and aerospace industry as well as in medical engineering field. Small components and tools with complex geome
Mat. Res.. Publicado em: 03/06/2019
-
8. Damping of Fe-Al Alloy Electrodeposited in an Ionic Liquid
Iron-Aluminium alloys were produced by the electro-deposition of iron-aluminium on a copper substrate. The electro-deposition process was done in the ionic liquid 1-butyl-1-methylpyrrolidinium trifluoromethylsulfonate, [Py1,4]TfO. A solution of (0.2 M FeCl2 + 2.75 M AlCl3)/ [Py1,4] TfO was used at a temperature of T=363 K because this mixture is solid at roo
Mat. Res.. Publicado em: 11/10/2018
-
9. Análisis de la corrosión de uniones por soldadura fuerte de compósitos matriz cobre
ABSTRACT This work presents an electrochemical corrosion study in synthetic seawater of the dissimilar joint of TiC/Cu composite by brazing technique. Composites were machined by liquid infiltration without external pressure. This composite were joined with copper using a filler material constituted by an alloy of silver - copper and titanium powder. The com
Matéria (Rio J.). Publicado em: 19/07/2018
-
10. Efecto del tratamiento sub-cero sobre la microestructura y dureza de fundiciones blancas alto cromo
ABSTRACT The effect of the sub-zero treatment temperature on the transformation of retained austenite to martensite in two high chromium white cast irons (ASTM A532 Class II Type B) was studied. The sub-zero treatment applied to each alloy in the as cast condition was performed at -40, -65 and -180 ° C for 10 minutes; after the holding time was completed th
Matéria (Rio J.). Publicado em: 19/07/2018
-
11. An Experimental Study of the Solidification Thermal Parameters Influence upon Microstructure and Mechanical Properties of Al-Si-Cu Alloys
Metals solidification involves the transformation of the molten metal back into the solid state. Solidification structures impact heavily on the final product's characteristics. The microstructure effects on metallic alloys properties have been highlighted in various studies and particularly the dendrite arm spacing influence upon the mechanical properties s
Mat. Res.. Publicado em: 18/06/2018
-
12. Thermomechanical Modelling of FSW Process Using a Cylindrical Tool in an Aluminum Alloy Alclad AA 2024-T3
The Friction Stir Welding Process (FSW/P) is an innovative technique to join metals using the plasticity, not occurring the melting. It was initially applied in aluminum alloys, but recently it has been extended to other materials, for example, copper, steel alloys, polimers and others. In this work it is analyzed the thermo mechanical modelling of the energ
Mat. Res.. Publicado em: 07/05/2018