Cast3m
Mostrando 1-12 de 61 artigos, teses e dissertações.
-
1. SYNTHESIS OF TOLUENE DIISOCYANATE URETHANE PREPOLYMER USING CASTOR OIL AND EVALUATION OF MECHANICAL PROPERTIES
This research is the synthesis of urethane prepolymer cast elastomer which had been produced using toluene diisocyanate and castor oil to replace the synthetic polyol, from petroleum origin, and the evaluation of mechanical properties of the polyurethane. The focus was to replace polyol from petroleum to vegetable material looking for renewable resources. Th
Química Nova. Publicado em: 2022
-
2. Activity of ceftolozane-tazobactam and comparators against gram-negative bacilli: Results from the study for monitoring antimicrobial resistance trends (SMART – Brazil; 2016–2017)
Abstract Multi-drug resistant Gram-negative bacilli (GNB) have been reported as cause of serious hospital-acquired infections worldwide. The aim of this study was to investigate the in vitro activity of ceftolozane-tazobactam compared to other agents against GNB isolated from patients admitted to Brazilian medical centers between the years 2016 and 2017. Pre
Braz J Infect Dis. Publicado em: 2020-08
-
3. Corrosion Resistance of Cu-Alloyed Precipitation Hardenable Duplex Stainless Steel ASTM A890 Grade 1B
Duplex stainless steels (DSS) are corrosion resistant alloys largely used in chemical and petrochemical industries. Some commercial DSS contain 0.5-1.0% copper addition to improve the corrosion resistance by reducing the corrosion rate in non-oxidizing environments. Higher copper addition (≥ 2%) can also hard by precipitation, especially when fine copper p
Mat. Res.. Publicado em: 07/11/2019
-
4. Corrosion Investigation of Stir Cast Zn-27Al Based Hybrid Composites Reinforced with Quarry Dust and Silicon Carbide Particles
This paper investigates the corrosion behaviour of Zn-27Al based hybrid composites reinforced with quarry dust (QD) and silicon carbide particles (SiCp). The Zn-27Al hybrid composites containing 8 wt% and 10 wt% SiCp-QD particles reinforcement with varied weight percentage of 0, 25, 50, 75 and 100% quarry dust respectively were synthesized using stir casting
Mat. Res.. Publicado em: 13/05/2019
-
5. Synthetic granite composite for precision equipment structures
ABSTRACT The structure is a component that plays an extremely important role in the equipment’s performance, it must withstand efforts without compromising the function, receive and transfer heat, dampen vibrations and position the elements, as well as promote ergonomics and aesthetics. In lightweight and precision equipment’s the raw material used must
Matéria (Rio J.). Publicado em: 06/12/2018
-
6. Evolución microestructural durante el envejecimiento a alta temperatura de una aleación 35Ni-25Cr-Nb
ABSTRACT The dendritic-type microstructure of the 35Ni-25Cr-Nb alloy, in the as-cast condition, consists of an austenitic matrix and two types of eutectic primary carbides; Nb-rich MC type and Cr-rich M23C6 type both presents in interdendritic edges and grain boundaries. During aging at 800ºC for different times, M23C6 type secondary carbides precipitate in
Matéria (Rio J.). Publicado em: 19/07/2018
-
7. Microstructural Evolution and Phase Transformation in Laser Cladding of Cr and Mo Powder on Grey Cast Iron: Mixture Design of Experiment (DOE)
Laser cladding on grey cast iron at high power processing was investigated for microstructural evolution and phase transformation to enhance surface properties. Cladding was designed using a mixture of DOE with peak power (Pp) and pulse repetition frequency (PRF), and a mixture component of Cr and Mo ratio as factors. Microstructural findings indicated absol
Mat. Res.. Publicado em: 21/11/2017
-
8. Effect of Ferrite on the Precipitation of σ Phase in Cast Austenitic Stainless Steel Used for Primary Coolant Pipes of Nuclear Power Plants
The effect of ferrite phase on the precipitation of σ phase in a Z3CN20.09M cast austenitic stainless steel (CASS) used for primary coolant pipes of pressurized water reactor (PWR) nuclear power plants was investigated by using isothermal heat-treatment, optical microscopy (OM), transmission electron microscopy (TEM) and electron probe microanalysis (EPMA)
Mat. Res.. Publicado em: 28/09/2017
-
9. Microstructure and Abrasion Resistance of Fe-Cr-C and Fe-Cr-C-Nb Hardfacing Alloys Deposited by S-FCAW and Cold Solid Wires
Abstract This work assesses the wear resistance behavior of different high Cr and Nb alloyed hardfacing deposits carried out by Self-shielded Flux Cored Arc Welding, considering the resulting microstructures as base for the analysis. To obtain non-commercial alloys, an “in-situ” technique was employed with addition of cold wire into the weld pool. Six co
Soldag. insp.. Publicado em: 2016-09
-
10. Effects of coronal substrates and water storage on the microhardness of a resin cement used for luting ceramic crowns
Composite resin and metallic posts are the materials most employed for reconstruction of teeth presenting partial or total destruction of crowns. Resin-based cements have been widely used for cementation of ceramic crowns. The success of cementation depends on the achievement of adequate cement curing. Objectives: To evaluate the microhardness of Variolink
J. Appl. Oral Sci.. Publicado em: 2014-07
-
11. Effect of the mechanical properties and mode loading on the mechanical behaviour of weldment: a numerical analysis
Welding is used to realize permanent assembly in mechanical structures to assure the continuity of the parts to be assembled contrary to the other assembly techniques which have physical or chemical discontinuities. Generally, crack evolution depends on several intrinsic and extrinsic parameters of material. The aim of this work is to analyse the severity of
Mat. Res.. Publicado em: 07/05/2013
-
12. Modelagem numérica da interface tubulação/revestimento em poços de petróleo / NUMERICAL SIMULATION OF TUBING/COATING INTERFACE IN OIL-WELLS
O petróleo tornou-se uma das principais fontes de energia do mundo contemporâneo e garantir que sua extração seja feita sem que haja perdas de produção e com poços estruturalmente confiáveis é fundamental. Os revestimentos cimentícios dos poços de petróleo são utilizados no intuito de garantir suporte estrutural aos poços e proteção contra co
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 13/08/2012