Cad Software
Mostrando 13-24 de 180 artigos, teses e dissertações.
-
13. Análise da microdureza Vickers de zircônia Y-TZP pré-sinterizada para a usinagem e posterior aplicação como copings
RESUMO A zircônia Y-TZP é muito utilizada na confecção de coping como material estrutural para próteses odontológicas devido à sua cor branca/perolada opaca e resistência mecânica. Estas próteses são confeccionadas por usinagem com apoio de um software de CAM (Computer Aided Manufacturing), a partir de blocos prensados e pré-sinterizados. A pré-
Matéria (Rio J.). Publicado em: 22/06/2017
-
14. ASPECTOS PRODUTIVOS DA MELANCIEIRA SOB IRRIGAÇÃO COM DÉFICIT E DIFERENTES COBERTURAS UTILIZANDO O MODELO ISAREG
RESUMO Objetivou-se avaliar a resistência de polpa e os sólidos solúveis dos frutos, e a produtividade da melancieira, sob diferentes proposições de irrigação (geradas pelo ISAREG) e condições de cobertura do solo; e seus efeitos de interação. Após pesquisa de campo junto aos irrigantes foram realizados dois experimentos na UEPE (Unidade de Ensin
Rev. Caatinga. Publicado em: 2017-06
-
15. Marginal and internal fit of zirconia copings obtained using different digital scanning methods
Abstract The objective of this study was to evaluate the marginal and internal fit of zirconia copings obtained with different digital scanning methods. A human mandibular first molar was set in a typodont with its adjacent and antagonist teeth and prepared for an all-ceramic crown. Digital impressions were made using an intraoral scanner (3Shape). Polyvinyl
Braz. oral res.. Publicado em: 10/10/2016
-
16. Comparative in vitro evaluation of CAD/CAM vs conventional provisional crowns
ABSTRACT Objective This study compared the marginal gap, internal fit, fracture strength, and mode of fracture of CAD/CAM provisional crowns with that of direct provisional crowns. Material and Methods An upper right first premolar phantom tooth was prepared for full ceramic crown following tooth preparation guidelines. The materials tested were: VITA CA
J. Appl. Oral Sci.. Publicado em: 2016-06
-
17. 3D virtual planning in orthognathic surgery and CAD/CAM surgical splints generation in one patient with craniofacial microsomia: a case report
Objetivo: neste relato de caso, de um paciente com microssomia craniofacial, testou-se a viabilidade e a precisão do planejamento virtual tridimensional (3D) utilizando o software Nemoceph 3D-OS (Software Nemotec SL, Madri, Espanha) para prever os resultados pós-operatórios em tecidos duros e produzir splints cirúrgicos CAD/CAM. Métodos: o protocolo
Dental Press J. Orthod.. Publicado em: 2016-02
-
18. Effect of software version and parameter settings on the marginal and internal adaptation of crowns fabricated with the CAD/CAM system
Objective This study investigated the marginal and internal adaptation of individual dental crowns fabricated using a CAD/CAM system (Sirona’s BlueCam), also evaluating the effect of the software version used, and the specific parameter settings in the adaptation of crowns. Material and Methods Forty digital impressions of a master model previously pre
J. Appl. Oral Sci.. Publicado em: 2015-10
-
19. A finite element study on the mechanical behavior of reciprocating endodontic files
AIM: To evaluate the mechanical behavior of reciprocating endodontic files, comparing nickel-titanium NiTi and stainless steel 316L St.St. 316L as manufacturing material for such instruments. METHODS: A three-dimensional finite element model was designed for this study. The simplified instrument model geometry was created on commercial CAD/CAM software. Rea
Braz. J. Oral Sci.. Publicado em: 2015-03
-
20. A systematic review on the evaluation and characteristics of computer-aided diagnosis systems
INTRODUCTION: One of the challenges in developing Computer-Aided Diagnosis (CAD) systems is their accurate and comprehensive assessment. This paper presents the conduction and results of a systematic review (SR) that aims to verify the state of the art regarding the assessment of CAD systems. This survey provides a general analysis of the current status of t
Rev. Bras. Eng. Bioméd.. Publicado em: 2014-12
-
21. Image analysis software versus direct anthropometry for breast measurements
PURPOSE: To compare breast measurements performed using the software packages ImageTool(r), AutoCAD(r) and Adobe Photoshop(r) with direct anthropometric measurements. METHODS: Points were marked on the breasts and arms of 40 volunteer women aged between 18 and 60 years. When connecting the points, seven linear segments and one angular measurement on ea
Acta Cir. Bras.. Publicado em: 2014-10
-
22. ARQUITECTURA HARDWARE-SOFTWARE PARA DISEÑO, ANÁLISIS Y CONTROL DE ROBOTS
This work presents a design and control methodology in real time using low cost hardware, working on a real robot as well as on a simulation, in a coordinated way. The methodology starts in the design phase using a CAD tool and generates the model of the robot in Matlab and Simulink as integration platforms, which are widely used tools in design and control
Publicado em: 02/06/2014
-
23. Evaluation of the adaptation of zirconia-based fixed partial dentures using micro-CT technology
The objective of the study was to measure the marginal and internal fit of zirconia-based all-ceramic three-unit fixed partial dentures (FPDs) (Y-TZP - LAVA, 3M-ESPE), using a novel methodology based on micro-computed tomography (micro-CT) technology. Stainless steel models of prepared abutments were fabricated to design FPDs. Ten frameworks were produced wi
Braz. oral res.. Publicado em: 2013-09
-
24. Nondestructive evaluation of wood decayed by xylophagous organisms
The aim of this study was to investigate the effects of attack by xylophagous organisms on the physicomechanical properties of Araucaria angustifolia wood from the floor of a historic house in Pelotas, Southern Brazil using two nondestructive methods. To achieve this, samples were collected from the floor for visual assessment by photography in metric scale.
Mat. Res.. Publicado em: 02/07/2013