Boron Alloys
Mostrando 1-12 de 22 artigos, teses e dissertações.
-
1. Integrated Experimental Approach for Alloying of Surface Layer Ti6Al4V+B4C Metal Matrix Composites using Laser Treatment
Surface engineering applications have brought the titanium and its alloys into the limelight in the manufacturing industries such as the aerospace, automobile, marine, chemical processing industry, nuclear power and biomedical. Despite the growths experienced in the use of this material, it is plagued with poor wear behaviour, especially when in contact with
Mat. Res.. Publicado em: 17/01/2019
-
2. Evolución microestructural in-situ a alta temperatura de depósitos de soldadura de aceros 9Cr con diferentes contenidos de boro
ABSTRACT New alloys have been developed for enhancing the performance of the equipment used in thermoelectric power generation industry. With the objective of increasing the creep resistance of these materials, changes in the content of some microalloying elements were carried out. Boron bearing in creep strength enhanced 9Cr steel (CSE9Cr) welds improved ma
Matéria (Rio J.). Publicado em: 19/07/2018
-
3. Optimization of the Deposition Parameters of HVOF FeMnCrSi+Ni+B Thermally Sprayed Coatings
AbstractHVOF thermal spray process produces coatings with low porosity and low oxide content, as well as high substrate adhesion. Small variations on the parameters of the HVOF process can generate coatings with different characteristics and properties, which also is chemical composition depended of the alloy. FeMnCrSi alloy is a cavitation resistant class o
Soldag. insp.. Publicado em: 2015-06
-
4. Study of Ti-7.5Si-22.5B alloys produced by powder metallurgy
Refractory alloys with silicides and borides have been used in high temperature applications because their elevated melting point, good oxidation resistance and high strength-to-weight ratio. The present study approaches the preparation of Ti-7.5Si-22.5B (at.-%) alloys through high-energy ball milling and sintering. The powders and compacts obtained in these
Mat. Res.. Publicado em: 03/06/2014
-
5. Isothermal section of the Ti-Si-B system at 1250 ° C in the Ti-TiSi2-TiB2 region
A partial isothermal section (Ti-TiSi2-TiB2 region) of the ternary Ti-Si-B system at 1250 ° C was determined from heat-treated alloys prepared via arc melting. Microstructural characterization has been carried out through scanning electron microscopy (SEM), x-ray diffraction (xRD) and wavelength dispersive spectrometry (WDS). The results have shown the stab
Mat. Res.. Publicado em: 22/10/2013
-
6. Microstructure and wear resistance of spray-formed supermartensitic stainless steel
Since the early 90's the oil industry has been encouraging the development of corrosion and wear resistant alloys for onshore and offshore pipeline applications. In this context supermartensitic stainless steel was introduced to replace the more expensive duplex stainless steel for tubing applications. Despite the outstanding corrosion resistance of stainles
Mat. Res.. Publicado em: 25/02/2013
-
7. On Ti-18Si-6B and Ti-7.5Si-22.5B powder alloys prepared by high-energy ball milling and sintering
Recently, a new ternary phase was discovered in the Ti-Si-B system, located near the Ti6Si2B composition. The present study concerns the preparation of titanium alloys that contain such phase mixed with α-titanium and other intermetallic phases. High-purity powders were initially processed in a planetary ball-mill under argon atmosphere with Ti-18Si-6B and
Mat. Res.. Publicado em: 09/10/2012
-
8. Microstructural characterization of as-cast hf-b alloys
An accurate knowledge of several metal-boron phase diagrams is important to evaluation of higher order systems such as metal-silicon-boron ternaries. The refinement and reassessment of phase diagram data is a continuous work, thus the reevaluation of metal-boron systems provides the possibility to confirm previous data from an investigation using higher puri
Materials Research. Publicado em: 14/02/2012
-
9. Estudo experimental do sistema Ta-Ge e da região rica em Ta do ternário Ta-Ge-B / Experimental Investigation of the Ta-Ge System and of the Ta Rich Region of Ta-Ge-B Ternary System.
Jet engines are important and complex engineering devices, whose efficiency and performance are directly related to the operating temperature of the combustion chamber, the higher the gas temperature in this region, the greater the overall efficiency of the process, resulting in economy of fuel and more efficiency. Ni-based superalloys are currently used in
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 22/05/2011
-
10. Obtenção e evolução da fase icosaedral quasicristalina em ligas Al-Cu-Fe e Al-Cu-Fe-B por Melt-Spinnin / OBTAINING AND EVOLUTION OF PHASE ICOSAHEDRAL QUASICRISTALINA IN ALLOYS Al-Cu-Fe AND Al-Cu-Fe-B BY MELT-SPINNING
Melt spinnng processing is one of the most common processes to obtaining quasicrystaline structures. This is because of the fast cooling rate it imposes on the system, favoring such type of structure. This work deals with the production of quasycristaline phases (Al60Cu27,5Fe12,5 e Al57Cu27,5Fe12,5B3) via melt-spinning. The alloys were initially cast via ind
Publicado em: 2009
-
11. Electroless cobalt alloys: magnetic and catalytic properties / Ligas à base de cobalto depositadas quimicamente: propriedades magnéticas e catalíticas
A influência de variáveis do banho na composição, microestrutura e nas propriedades magnéticas de filmes de CoB preparados por deposição química foi estudada. Dois diferentes tipos de agentes complexantes foram utilizados: citrato de sódio e Glicina. Filmes com menor teor de boro foram obtidos com o uso de Glicina como complexante. A deposição de
Publicado em: 2009
-
12. Estudo da influência da temperatura nas propriedades magnéticas e na microestrutura nos ímãs permanentes à base de Pr-Fe-B-Nb-Co obtidos com hidrogênio / Study of the influence of the temperature in the magnetic properties and in microstructure in the permanent magnets Pr-Fe-B-Nb-Co based obtained by hydrogen
Pós magnéticos foram produzidos utilizando o processo de hidrogenação, desproporção, dessorção e recombinação (HDDR). A primeira parte deste trabalho envolveu o estudo do efeito da adição de Co na liga Pr14FebalCoxB6Nb0.1 (x= 0, 4, 8, 10, 12, 16) variando a de temperatura de dessorção/ recombinação de 800° a 900°C, com o objetivo de otimiza
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 23/11/2007