Bending Behaviour
Mostrando 1-12 de 26 artigos, teses e dissertações.
-
1. Evaluation of the stiffening mechanism based on micro-sized particle inclusions in laminated composites
Rigid particles have been incorporated into laminated composites, especially to enhance their bending performance attributed to the stiffening of the matrix phase (i) and the increased interlaminar shear resistance (ii). In order to better evaluate the improvement mechanism provided by the particulate inclusions, this work investigates the incorporation of m
Mat. Res.. Publicado em: 17/10/2019
-
2. Characterization of hibiscus sabdariffa fiber as potential reinforcement for denture acrylic resins
ABSTRACT This study aimed to determine the characteristics of Hibiscus sabdariffa as a fiber-reinforcement material for denture acrylic resins. The Hibiscus sabdariffa fiber was extracted by hot water retting. The fiber was treated at room temperature in aqueous solution of NaOH for 8 hours at 8% concentration. Micrometre gauge and Field emission scanning el
Matéria (Rio J.). Publicado em: 06/12/2018
-
3. Mechanical behaviour of steel fiber reinforced concrete with stone powder
ABSTRACT Nowadays, there is an increasing interest in the development of eco-friendly materials. Thus, environmental challenges due to the necessity of reducing worldwide levels of CO2 emissions, to limit the energy consumption and to use industrial waste are promoting an increasing effort to find viable alternatives to minimize pollution from the main produ
Matéria (Rio J.). Publicado em: 20/07/2017
-
4. Non-Linear Three Dimensional Finite Elements for Composite Concrete Structures
Abstract The current investigation focused on the development of effective and suitable modelling of reinforced concrete component with and without strengthening. The modelling includes physical and constitutive models. New interface elements have been developed, while modified constitutive law have been applied and new computational algorithm is utilised. T
Lat. Am. j. solids struct.. Publicado em: 2017-03
-
5. Acoustic Emission Analysis of Cement Mortar Specimens During Three Point Bending Tests
Abstract This work discusses the experimental results of Acoustic Emission (AE) recordings during repetitive loading/unloading loops of cement mortar beams subjected to three point bending. Six repetitive loading cycles were conducted at a gradually higher load level until the failure of the specimens. The experimental results clearly show the existence and
Lat. Am. j. solids struct.. Publicado em: 2016-12
-
6. Influence of local raw materials on the mechanical behaviour and fracture process of PVA-SHCC
This paper addresses the results of an investigation on the influence of the Brazilian raw materials on the mechanical performance of Strain Hardening Cementitious Composites (SHCC). The mixtures were produced with variations of fly ash/cement and sand/cement proportions and with different maximum sand particle. Mechanical properties were evaluated by direct
Mat. Res.. Publicado em: 08/10/2013
-
7. Normalizing effect on fatigue crack propagation at the heat-affected zone of AISI 4140 steel shielded metal arc weldings
The fractography and mechanical behaviour of fatigue crack propagation in the heat-affected zone (HAZ) of AISI 4140 steel welded using the shielded metal arc process was analysed. Different austenitic grain size was obtained by normalizing performed at 1200 °C for 5 and 10 hours after welding. Three point bending fatigue tests on pre-cracked specimens along
Mat. Res.. Publicado em: 02/04/2013
-
8. Flexural behavior of Sisal/Castor oil-Based Polyurethane and Sisal/Phenolic Composites
Natural fibers used as reinforcement of polymeric composites are interesting research subjects in polymer technology. Nowadays, these materials are being considered as a way to reinforce timber structures improvement. Fibers with larger structural applications are glass and carbon fibers, however, the use of natural fibers is an economic alternative and pres
Materials Research. Publicado em: 24/02/2012
-
9. An extension of coupled beam method and its application to study ship's hull-superstructure interaction problems
This paper describes an extended formulation for the coupled beam method (CBM). The method is originally developed for elastic bending response analysis of passenger ships with large multi-deck superstructures. The extension is mainly performed to enable the available method in order to study elastic bending behaviour of ships fitted with superstructures of
Latin American Journal of Solids and Structures. Publicado em: 2011-09
-
10. Experimental study of structural behavior of curved bars. / Estudo experimental do comportamento estrutural de barras curvas.
This dissertation deals with an experimental study on the structural behavior of bars supported on a helical cylindrical surface and subject to compressive loads. A special experimental apparatus was designed and built for this purpose. The design, as well as the adjustment of such an apparatus is described in details. The device allows one adjusting the bar
Publicado em: 2009
-
11. Avaliação do comportamento mecânico ao cisalhamento de conectores de barras de aço com ganchos em vigas mistas de madeira laminada colada e concreto
The main objective of this work was to propose a reference specimen for the push-out test of rod-type fasteners in timber-concrete connections. The following experimental tests have been performed in order to achieve the goals of this research: pull-out tests of bonded-in steel rods in wood specimens, pull-out tests of bonded-in steel rods in concrete specim
Publicado em: 2008
-
12. Design of an experimental flutter mount system
Aeroelastic instabilities may occur in aircraft surfaces, leading then to failure. Flutter is an aeroelastic instability that results in a self-sustained oscillatory behaviour of the structure. A two-degree-of-freedom flutter can occur with coupling of bending and torsion modes. A flexible mount system has been developed for flutter tests in wind tunnels. Th
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2007-09