Backscatter
Mostrando 1-12 de 55 artigos, teses e dissertações.
-
1. Study of Mechanical Behavior and X-Ray Elastic Constants of Nickel Alloy Weld Overlay
The study of nickel-based alloy 625 clad (weld overlay) by X-ray diffraction (XRD) is difficult and often impossible because of its coarse and anisotropic microstructure. In this work, a sample preparation including machining, grinding, and annealing was proposed to avoid this negative effect in XRD analysis. Electron backscatter diffraction and hardness tes
Mat. Res.. Publicado em: 10/07/2019
-
2. Performance of the INCONEL 625 alloy weld overlay obtained by FCAW process
ABSTRACT Nickel-based weld overlays (cladding) are commonly used in oil & gas industry to extend the life of equipment under corrosive environment, as it improves the corrosion resistance without a significant increase in the manufacturing cost, when compared to a full nickel-based alloy equipment. Although there are extensive literature involving overlays a
Matéria (Rio J.). Publicado em: 20/05/2019
-
3. ANALYSIS OF THE TARGET DECOMPOSITION TECHNIQUE ATTRIBUTES AND POLARIMETRIC RATIOS TO DISCRIMINATE LAND USE AND LAND COVER CLASSES OF THE TAPAJÓS REGION
Resumo Este trabalho tem como objetivo analisar a capacidade dos atributos das técnicas de decomposição de alvos e dos atributos de retroespalhamento, provenientes das imagens polarimétricas do satélite ALOS/PALSAR-2, para discriminar as classes de uso e cobertura da terra na região da Floresta Nacional do Tapajós (FNT), estado do Pará. Três imagens
Bol. Ciênc. Geod.. Publicado em: 18/04/2019
-
4. EBSD Analysis of Orientation Gradients Developed near Grain Boundaries
The local misorientation and orientation gradient development near grain boundaries (GBs) are analyzed in a deep drawing quality steel sheet (AKDQ) subjected to interrupted tensile tests in a notched sample. The microstructure is studied using electron backscatter diffraction (EBSD) with subgrain-level spatial resolution. The evolution of misorientation accu
Mat. Res.. Publicado em: 10/01/2019
-
5. Analysis of the Crystallographic Microtexture of a UNS S32205 and a UNS S32304 Duplex Stainless Steels After Cold Rolling and Heat Treatment
Samples of duplex stainless steel 32205 (standard duplex) and 32304 (lean duplex) were investigated in the as-received state, cold rolling (with thickness reduction of 64 % and 62 % respectively) and after annealing at 1055ºC for 20 s soaking. Crystallographic microtexture was obtained via Electron BackScatter Diffraction (EBSD) technique. The results showe
Mat. Res.. Publicado em: 26/07/2018
-
6. Gradientes de orientación en cercanías del borde de grano estudiados por EBSD
ABSTRACT The goal of this study is the evaluation of local misorientation, its distribution and orientation gradient in the microstructural development of a deep drawing quality steel sheet (AKDQ). The microstructure is characterized at sub-grain level spatial resolution using Electron Backscatter Diffraction (EBSD) in samples submitted to interrupted uniaxi
Matéria (Rio J.). Publicado em: 19/07/2018
-
7. Evolución microestructural durante el envejecimiento a alta temperatura de una aleación 35Ni-25Cr-Nb
ABSTRACT The dendritic-type microstructure of the 35Ni-25Cr-Nb alloy, in the as-cast condition, consists of an austenitic matrix and two types of eutectic primary carbides; Nb-rich MC type and Cr-rich M23C6 type both presents in interdendritic edges and grain boundaries. During aging at 800ºC for different times, M23C6 type secondary carbides precipitate in
Matéria (Rio J.). Publicado em: 19/07/2018
-
8. Application of Friction Surfacing to the Production of Aluminum Coatings Reinforced with Al2O3 Particles
The aim of this work was to produce deposits of AA6351-T6, reinforced with alumina (Al2O3) particles, over a substrate of AA5052-H32 through friction surfacing. AA6351-T6 consumable rods were drilled with one and two holes, which were filled with Al2O3 particles posteriorly. To perform the deposition, a conventional KONE KFE-3/BR milling machine was used. Th
Mat. Res.. Publicado em: 13/11/2017
-
9. Microstructure, Texture and Microhardness Evolution during Annealing Heat Treatment and Mechanical Behavior of the Niobium-Stabilized Ferritic Stainless Steel ASTM 430 and Niobium-Titanium-Stabilized Ferritic Stainless Steel ASTM 439: a Comparative Study
A comparison of the influence of microstructure and texture on mechanical behavior between the niobium-stabilized ferritic stainless steel type ASTM 430, 430Nb, and the niobium-titanium-stabilized ferritic stainless steel type ASTM 439 was performed. The two steels were supplied as cold rolled thin sheets and the annealing was interrupted in different tempe
Mat. Res.. Publicado em: 18/09/2017
-
10. Characterization of the Austenite Reformation Mechanisms as a Function of the Initial Ferritic State in a UNS S32304 Duplex Stainless Steel
Aiming to better understand the effects of heat treatment parameters on Ferrite-Austenite phase transformation in a 2304 duplex stainless steel different thermal cycles were applied to this steel in a quenching dilatometer. The obtained microstructures were characterized by optical microscopy, transmission electron microscopy and electron backscatter diffrac
Mat. Res.. Publicado em: 17/08/2017
-
11. Evaluation of Intermediate Annealing on Nb-Stabilized Ferritic Stainless Steel
This study seeks to evaluate the effect of intermediate annealing on the microstructure, texture, and formability of Nb-stabilized ferritic stainless steel. Two routes - direct cold rolling and cold rolling with an intermediate annealing were performed. The total reduction was 80%, 3-0.6 mm and 3-1.2-0.6 mm. The characterization of the samples was conducted
Mat. Res.. Publicado em: 07/08/2017
-
12. Microstructural Stability of a Niobium Single Crystal Deformed by Equal Channel Angular Pressing
A [211]-oriented niobium single crystal was deformed by equal channel angular pressing (ECAP) at room temperature using the route Bc to a total strain of 9.2. A sharp cube texture develops after ECAP processing. The deformed samples were annealed in vacuum from 400ºC (673 K) to 900ºC (1173 K) for 1 h to evaluate their microstructural stability. Scanning el
Mat. Res.. Publicado em: 13/07/2017