Amorphous Coatings
Mostrando 1-12 de 26 artigos, teses e dissertações.
-
1. Dependence of Wear and Mechanical Behavior of Nitrocarburized/CrN/DLC Layer on Film Thickness
Diamond-like carbon (DLC) films are amorphous metastable carbon form that provide interesting mechanical and tribological properties. The role of film thickness influence upon wear and mechanical properties is of interest and not yet fully reported. In this study, two samples of previously plasma nitrocarburized, quenched and tempered H13 steel were duplex t
Mat. Res.. Publicado em: 31/01/2019
-
2. Tribological behavior of hydrogenated W-C/a-C:H coatings deposited by three different sputtering techniques
Abstract The evolution of structure, mechanical properties and friction behavior of DC magnetron sputtered (DCMS), high power impulse magnetron sputtered (HiPIMS) and high target utilization sputtered (HiTUS) W-C:H coatings was investigated as a function of the addition of acetylene and hydrogen into Ar atmosphere. The gradual addition of reactive gases caus
Cerâmica. Publicado em: 2019-01
-
3. Influencia de los tratamientos térmicos en recubrimientos anódicos nanotubulares de TiO2
ABSTRACT TiO2 is a semiconductor widely used in heterogeneous photocatalysis processes for water decontamination. Several studies indicate that ordered nanostructures in anatase phase improve the photocatalytic properties with respect to other morphologies and crystal structures of TiO2. The aim of the present work is to evaluate the influence of different t
Matéria (Rio J.). Publicado em: 19/07/2018
-
4. Efectos de tratamientos térmicos post-alcalinos sobre las propiedades superficiales de titanio para implantes dentales con diferentes recubrimientos
ABSTRACT Titanium is widely used as dental implant since it is bio-inert and osseointegratable. However, provided that this material cannot induce bone growth from its surface, it is usual to carry out different surface treatments in order to develop bioactive coatings that increase both the initial rate of bone development and the biological anchorage of im
Matéria (Rio J.). Publicado em: 19/07/2018
-
5. Surface, microstructural, and adhesion strength investigations of a bioactive hydroxyapatite-titanium oxide ceramic coating applied to Ti-6Al-4V alloys by plasma thermal spraying
Ti-6Al-4V alloy is employed in implants because of its good mechanical strength, excellent biocompatibility, and good resistance to corrosion in biological environments. Herein, a composite (HAp-TiO2, 50% by volume of both components) coating surface employing Ti-6Al-4V was characterized. Samples were analyzed post fabrication and post heat treatment to anal
Mat. Res.. Publicado em: 28/05/2018
-
6. Microstructure and Flight Behaviors of Droplet and its Solidification in Twin-Wire Arc Sprayed Ni-Al Composite Coatings
Droplet flight and solidification behaviors during twin-wire arc sprayed (TWAS) composite coatings were systematically investigated. Both theoretical model and numerical method were established for calculating the droplet deformation, breakup and solidification process in air flow based on the volume of fluid (VOF) dual-phase flow model jointed with the stan
Mat. Res.. Publicado em: 19/03/2018
-
7. Laser Cladding of Fe-based Metallic Glass/MoS2 Self-lubricating Composites: Effect of Power and Scanning Speed
MoS2 powder has been used to form "self-lubricating" composite coatings, which are very useful to increase the lifetime of machines where liquid lubricants cannot be used. In this work, amorphous overspray powder of Fe60Cr8Nb8B24 (at%) alloy was mixed with 5wt.% MoS2 powder and it was used to produce single tracks on AISI 1020 steel substrates by laser cladd
Mat. Res.. Publicado em: 01/02/2018
-
8. Thermal Spraying Processes and Amorphous Alloys: Macro-Indicators of Patent Activity
Thermal spraying processes allows high cooling rates and can favor the formation of amorphous microstructures. Amorphous metallic coatings can result in superior mechanical and functional properties. To follow new technological development and innovation paths, indicators based on patent data can be assembled to support technological forecasting assessments
Mat. Res.. Publicado em: 04/12/2017
-
9. Metallic Glass Formation Upon Rapid Solidification of Fe60Cr8Nb8B24 (at%) Alloy through LASER Cladding and Remelting
Fe60Cr8Nb8B24 (at%) amorphous powder and ingot were submitted to LASER cladding and remelting process, respectively. Fe-based coatings were produced using different LASER processing parameters and characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and Vickers microhardness. All coatings obtained by LASER cladding (LC) and layers obt
Mat. Res.. Publicado em: 17/11/2017
-
10. Assessing Collaboration and Knowledge Flow on Coatings of Metallic Glasses Obtained From Thermal Spraying Processes Using Bibliometrics and Science Mapping
Coatings of amorphous metallic alloys can be obtained using different thermal spraying processes, such as HVOF, plasma spraying, cold spraying and others. Although many studies focused on investigating scientific issues concerning apply amorphous metallic coatings using thermal spraying, less attention have been paid to evaluate how research institutes and c
Mat. Res.. Publicado em: 13/11/2017
-
11. Wear Behaviour of Electroless heat Treated Ni-P Coatings as Alternative to Electroplated hard Chromium Deposits
In this present study was evaluated the influence of heat treatment on the wear resistance of electroless high phosphorus nickel coating (9-10% P wt.). In addition, both untreated and treated Ni-P deposits were then compared to electroplated hard chromium coatings in terms of wear behaviour. Three different heat treatment conditions were performed at tempera
Mat. Res.. Publicado em: 24/07/2017
-
12. Films Deposited from Reactive Sputtering of Aluminum Acetylacetonate Under Low Energy Ion Bombardment
Films were deposited from aluminum acetylacetonate (Al(acac)3) using a methodology involving reactive sputtering and low energy ion bombardment. The plasma was generated by the application of radiofrequency power to the powder containing electrode and simultaneously, negative pulses were supplied to the electrode where the substrates were attached. It was in
Mat. Res.. Publicado em: 10/04/2017