Aluminium Alloy
Mostrando 1-12 de 69 artigos, teses e dissertações.
-
1. Tensile and fatigue properties, machinability and machined surface roughness of Al-Si-Cu alloys
ABSTRACT In this paper, the aim was to determine if ASC91 (9 % Al, 1 % Cu) could be replaced with ASC73 (7 % Al, 3 % Cu) aluminium alloy, with presumably improved machinability due to lower silicon content (9 to 7 %) and retained mechanical properties due to a higher copper content (1 to 3 %). The test samples were excised from cylinder heads produced by the
Matéria (Rio J.). Publicado em: 16/09/2019
-
2. Mechanical Properties and Metallurgical Characterization of LM25/ZrO2 Composites Fabricated by Stir Casting Method
ABSTRACT Zirconia (ZrO2) dispersed aluminum alloy metal matrix composites produced by stir casting techniques. Using stir casting techniques, aluminium based composites with varying amounts of 3%, 6%, 9%, and 12% of zirconia by weight are fabricated. The prepared samples were subjected to physical, mechanical,tribiology and microstructure investigation. The
Matéria (Rio J.). Publicado em: 16/09/2019
-
3. Effect of Extrusion and Heat Treatment on Microstructure and Mechanical Properties of Hypereutectic A390-0.3wt%Nd Alloy
An hypereutectic aluminium alloy with a composition of 16-18wt%Si, 4-5wt%Cu, 0.45-0.65wt%Mg, 0.3wt%Nd and Al balance (A390-0.3wt%Nd alloy) was processed by extrusion and aging at 200ºC for 10 hours. The effect of the thermomechanical processing and heat treatment on microstructure and mechanical properties was investigated for A390-0.3wt%Nd alloy. It was sh
Mat. Res.. Publicado em: 10/06/2019
-
4. Corrosion and Micro-abrasive Wear Behaviour of 2524-T3 Aluminium Alloy with PAni-NPs/PSS LbL Coating
In this paper, we present an alternative method to obtain thin films for coating protection on the surface of the AA2524-T3 Al-alloy by using the Layer-by-Layer (LbL) technique. The LbL films were fabricated by alternated immersion of the Al-alloy into a poly(styrene sulfonate) (PSS) and polyaniline nanoparticles (PAni-NPs) solutions, obtaining a PAni-NPs/PS
Mat. Res.. Publicado em: 06/06/2019
-
5. On the Global and Localised Corrosion Behaviour of the AA2524-T3 Aluminium Alloy Used as Aircraft Fuselage Skin
The aim of this work was to study the corrosion process of new aluminium alloy AA2524-T3 (Solution Heat Treated and Cold Worked), which is a promising substitute of the base line AA2024-T3 for aircrafts fabrication, by global and localised techniques in sodium chloride medium (0.05 mol L-1 NaCl). The open circuit potential results revealed a stochastic evolu
Mat. Res.. Publicado em: 14/01/2019
-
6. Optimization of Multiple Performance Characteristics of Friction Stir Welded Joint with Grey Relational Analysis
In the present work, multi-objective optimization of the input welding parameters influencing the quality of weld joint of AA 5052 H32 aluminium alloy by FSW process is investigated using response surface methodology and grey relational analysis. The quality of the welded joint is measured based on the higher value of tensile strength and hardness of the joi
Mat. Res.. Publicado em: 08/11/2018
-
7. Submerged Friction Stir Welding of 6061-T6 Aluminium Alloy under Different Water Heads
The aim of this paper is to determine the feasibility of submerged friction stir welding of 6061-T6 aluminium alloy on different water heads through macrostructuralanalysis.In this work, aluminium 6061-T6 alloy was friction stir welded under normal and submerged conditions at different rotational speeds of 400 rpm, 800 rpm, 1200 rpm, 1600 rpm. The water head
Mat. Res.. Publicado em: 01/11/2018
-
8. Damping of Fe-Al Alloy Electrodeposited in an Ionic Liquid
Iron-Aluminium alloys were produced by the electro-deposition of iron-aluminium on a copper substrate. The electro-deposition process was done in the ionic liquid 1-butyl-1-methylpyrrolidinium trifluoromethylsulfonate, [Py1,4]TfO. A solution of (0.2 M FeCl2 + 2.75 M AlCl3)/ [Py1,4] TfO was used at a temperature of T=363 K because this mixture is solid at roo
Mat. Res.. Publicado em: 11/10/2018
-
9. Effect of Solidification Processing Parameters and Silicon Content on the Dendritic Spacing and Hardness in Hypoeutectic Al-Si Alloys
Aluminium with silicon as alloying element, form a class of material providing the most significant part of all material casting manufactured materials. These alloys have a wide range of applications in the automotive and aerospace industries. It is widely recognized that moderate addition of silicon to aluminum, significantly improves the resulting mechanic
Mat. Res.. Publicado em: 17/09/2018
-
10. Study of friction stir spot welding on AA6063 aluminium alloy used in the ship building industry
ABSTRACT Friction stir spot welding (FSSW) is a novel process of metal joining. In the present work, the authors analysed the possibility of using this process to solve current problems in shipbuilding industry regarding small vessels by replacing the current arc welding techniques with the aforementioned process. Numerical simulation was carried out by the
Matéria (Rio J.). Publicado em: 19/07/2018
-
11. Rheo-Squeeze Casting of High-Silicon Aluminium Alloy Pipes with Gradient Structures and Their Mechanical Properties
Three different compositions of high-Si Al alloy pipe, with a gradient structure, were produced through semi-solid rheological squeeze casting, the microstructural characteristics of which were investigated. The mechanism of gradient structure formation and the effect of acicular Fe-rich phases on liquid segregation were revealed. Meanwhile, the crystal stru
Mat. Res.. Publicado em: 11/06/2018
-
12. Microstructural and Electrochemical behaviour of Aluminium Alloy Composites Produced Using Different Sintering Techniques
Present research work analyses the effect of heating modes on the densification, microstructure and mechanical properties of aluminum alloys [65Al-20Cu-15Mn] fabricated through powder metallurgy route. Sintering of compacts using conventional, microwave and spark plasma sintering methods has been carried out at 525°C. From the results, it has been observed
Mat. Res.. Publicado em: 12/03/2018