Aisi H13
Mostrando 1-12 de 34 artigos, teses e dissertações.
-
1. EXTRATO DE HIBISCO-COLIBRI COMO INIBIDOR VERDE DE CORROSÃO DO AÇO-CARBONO EM ÁCIDO SULFÚRICO
For this work, a hydroalcoholic extract was prepared from the aerial parts of the Malvaviscus arboreus (Malvaceae) species, popularly known as hibisco-colibri in Brazil; and then, investigated by infrared and NMR spectroscopy. A class of special metabolites containing a porphyrin skeleton and pyrrole units was determined by typical absorption spectra, mainly
Quím. Nova. Publicado em: 26/08/2019
-
2. Validação de um Sistema Robotizado Recém Desenvolvido para a Soldagem pelo Processo Friction Stir Welding por meio da União e Caracterização de Juntas da Liga de Alumínio 5052 H34
Resumo Este projeto trata da validação de um sistema recém desenvolvido para a soldagem pelo processo friction stir welding, que foi adaptado a um robô antropomórfico com capacidade de 500 kg e seis graus de liberdade. Para garantir que o sistema projetado é capaz de soldar materiais pelo processo FSW, ou seja, garantir que possui rigidez, resistência
Soldag. insp.. Publicado em: 21/12/2017
-
3. Effect of Processing Route on the Microstructure and Mechanical Properties of Hot Work Tool Steel
Powder metallurgy is a growing sector in industrial production, as it offers outstanding energy, cost and material savings in comparison with established processing routes such as casting. Hot work toll steels are usually produced by ingot metallurgy, but also by powder metallurgy, namely hot isostatic pressing and powder forging routes. In this paper we inv
Mat. Res.. Publicado em: 21/08/2017
-
4. Micro-Scale Abrasive Wear Testing of CrN Duplex PVD Coating on Pre-Nitrided Tool Steel
Specific wear rates were calculated from a series of micro-scale abrasive tests by means of the calotte-grinding method. The tested material was a CrN coating deposited by arc evaporation on ion-nitrided AISI H13 steel. Characterizations included: phase analysis, chemical composition, metallography, microhardness, micro-scratch resistance and nano-indentatio
Mat. Res.. Publicado em: 22/06/2017
-
5. Study of the nitrided layer obtained by different nitriding methods
In this study, plasma nitriding, gas nitriding and solid nitriding were performed in AISI H13, AISI P20 and N-8550 tool steels. The aim of the study was compare the acquired properties after the thermochemical treatments and evaluate the efficiency of the solid nitriding treatment. The samples were analyzed using a microhardness tester and a scanning electro
Matéria (Rio J.). Publicado em: 2015-06
-
6. Acquired Properties Comparison of Solid Nitriding, Gas Nitriding and Plasma Nitriding in Tool Steels
Plasma nitriding, gas nitriding and solid nitriding were applied in tool steels (AISI H13, AISI P20 and N-8550). The acquired properties were compared and evaluated on these three processes with the aim to verify the solid nitriding performance. In order to promote the solid nitriding, the samples were surrounded by a solid compound with the Fe4KCN stoichiom
Mat. Res.. Publicado em: 2015-02
-
7. Influência da variação do tamanho de grão austenítico na qualidade superficial no processo de microfresamento do aço AISI H13 endurecido
O foco deste trabalho foi o estudo da influência do tamanho de grão austenítico na qualidade superficial durante o processo de micro fresamento de aços endurecidos. Corpos de prova com durezas de 46 HRC e com diferentes tamanhos de grão foram fresados com micro fresas de topo com 0,5 mm de diâmetro. Nos testes experimentais foram empregadas duas veloci
Matéria (Rio J.). Publicado em: 2014-09
-
8. Estudo do comportamento tribológico do aço AISI H13 submetido a tratamento termoquímico de boretação / Study of tribological behavior of AISI H13 steel subjected to boriding thermochemical treatment
In this work, solid boriding thermochemical treatment was carried out using Ekabor 1-V2 and one blend as boriding agents and heat treatment of quenching and tempering of AISI H13 tool steel in order to compare and evaluate the tribological behavior and the properties acquired for four studied conditions, that were: Ekabor powder boriding, Ekabor powder borid
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 18/06/2012
-
9. Influence of the microstructure on the electrochemical properties of Al-Cr-N coatings deposited by co-sputtering method from a Cr-Al binary target
In the present paper, aluminum chromium nitride (Al-Cr-N) films were deposited onto AISI H13 steel substrates by a reactive d.c magnetron co-sputtering system in an atmosphere of Ar/N2 (90/10) gas mixture from a binary target composed of chromium (99.95%) and aluminum (99.99%). Different powers (40, 50, 60, and 70 W) were applied to the target, in order to s
Mat. Res.. Publicado em: 04/12/2012
-
10. Estudo da integridade superficial e seu efeito na fadiga de contato de um aço ferramenta. / The effect of surface integrity on the contact fatigue resistance of a tool steel.
Os processos de manufatura, bem como os parâmetros de processamento utilizados produzem diferentes resultados com relação à integridade de uma superfície. Estas alterações se refletem em mudança das propriedades da superfície, as quais podem influenciar o desempenho dos componentes. O presente trabalho estuda o efeito da integridade superficial gera
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 19/09/2011
-
11. Estudo da influência do tratamento criogênico no aço AISI H13 / Study of the influence of cryogenic treatment in AISI H13 steels
Há alguns anos, diversos estudos da influência dos parâmetros do tratamento térmico vêm sendo desenvolvidos, para a obtenção de propriedades que permitam atingir os requisitos de trabalho e que gerem ferramentas de vida útil estendida. Nesse contexto, tem sido demonstrado que o tratamento criogênico não só provoca a transformação da austenita re
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 21/02/2011
-
12. Caracterização e avaliação tribológica de superfícies resistentes ao desgaste para aplicação em ferramentas de conformação a frio
O desgaste é o fator que causa a maior parte das falhas e a redução na vida útil de ferramentas de conformação, além de resultar em produtos com condições superficiais intoleráveis. A crescente demanda da indústria por menores custos, maior produtividade e melhor qualidade estão entre as justificativas para que se busquem maneiras de incrementar
Publicado em: 2011