Additive
Mostrando 1-12 de 2360 artigos, teses e dissertações.
-
1. Influence of Refinery Asphalt Residue Addition on Flow: A Study Using Waxy Model-System
One of the main phenomena causing problems in the oil industry is the precipitation of waxes, which can crystallize and form deposits, clogging lines and reducing flows. Many studies have been conducted seeking to overcome this problem, mainly through application of chemical to increase flow. Some studies have shown that the asphaltenes present in crude oil
Journal of the Brazilian Chemical Society. Publicado em: 2023
-
2. A review on the ceramic additive manufacturing technologies and availability of equipment and materials
Abstract Ceramic additive manufacturing allows the fabrication of small series of complex parts without the high costs of molds usually associated with traditional ceramic processing. Although research into ceramic 3D printing by all technologies started back in the 90s, its industrial application is still quite restricted when compared to polymers and metal
Cerâmica. Publicado em: 2022
-
3. Behavior of plaster with water-repellent additive under natural aging
Abstract This research evaluates the behavior of plaster with a water-repellent additive when submitted to a natural aging process. Casting plaster and silane/siloxane-based water-repellent were used as materials. The water/plaster ratio was set at 0.7 and the contents of 0.2% and 0.4% of water-repellent were used, in relation to the plaster mass. Plaster pa
Cerâmica. Publicado em: 2022
-
4. Evaluation of the use of blast furnace slag as an additive in mortars
Abstract Clinker is the raw material used in the manufacture of cement. However, this material is very harmful to the environment, since it is estimated that for every ton of clinker produced, about 1.0 ton of CO2 is released into the atmosphere. For this reason, alternatives were sought for the use of other materials that are less harmful to the environment
REM - International Engineering Journal. Publicado em: 2022
-
5. Additive Manufacturing towards the Fabrication of Greener Electrochemical Sensors for Antioxidants
Additive manufacturing is an emerging tool that has contributed to the sustainable fabrication of devices in several areas based on the concept of “zero waste”. Considering extrusion-based manufacturing (or 3D printing), polylactic acid (PLA) has been highlighted due to its biodegradability, obtention from renewable sources, and compatibility for 3D prin
Journal of the Brazilian Chemical Society. Publicado em: 2022
-
6. Seleno- and Telluro-Functionalization of Quinones: Molecules with Relevant Biological Application
Quinones and organochalcogens are classes of compounds with great biological applicability, such as antioxidant, anticancer, anti-Alzheimer, and antidepressant activities, among others. Thus, the combination of these two classes of compounds is important to obtain new hits with biological activities that are additive or synergistic. Several methodologies for
Journal of the Brazilian Chemical Society. Publicado em: 2022
-
7. Development of a ceramic membrane for emulsion water-diesel treatment
Abstract The purpose of this study was the development of a low-cost ceramic tubular membrane, using inexpensive materials, namely natural clay, and graphite as a porogenic agent. Such a low-cost membrane can be used as filters or porous supports for the preparation of multilayer ceramic membranes. Extrusion was used as a shape-forming method for this purpos
Cerâmica. Publicado em: 2022
-
8. Impact assessment of emergency care units on hospitalizations for respiratory system diseases in Brazil
Resumo As Unidades de Pronto Atendimento 24h (UPAs) compõem a Política de Atenção a Urgências e Emergências (PNAU) implementada pelo Governo Federal. São componentes pré-hospitalares fixos do SUS, cujo objetivo é o atendimento resolutivo de urgência a pacientes que sofrem quadros clínicos agudos, e o primeiro atendimento em casos cirúrgicos. Desd
Ciência & Saúde Coletiva. Publicado em: 2022
-
9. Collector mixtures and their synergistic effect on quartz floatability
Abstract Sinergy is the interaction of two or more agents to produce a combined effect greater than the sum of their separate effects. Etherdiamine yields superior results for quartz floatability in a Hallimond tube and higher selectivity in the reverse bench scale cationic flotation of an iron ore, when compared to ethermonoamine. Blending these collectors
REM - International Engineering Journal. Publicado em: 2022
-
10. The A allele of the rs759853 single nucleotide polymorphism in the AKR1B1 gene confers risk for diabetic kidney disease in patients with type 2 diabetes from a Brazilian population
ABSTRACT Objective: The AKR1B1 gene encodes an enzyme that catalyzes the reduction of glucose into sorbitol. Chronic hyperglycemia in patients with diabetes mellitus (DM) leads to increased AKR1B1 affinity for glucose and, consequently, sorbitol accumulation. Elevated sorbitol increases oxidative stress, which is one of the main pathways related to chronic
Archives of Endocrinology and Metabolism. Publicado em: 2022
-
11. Effect of Lippia grata essential oil as a feed additive on the performance of tambatinga juveniles
RESUMO Lippia grata (previamente conhecida como Lippia gracillis) é uma planta aromática nativa do Brasil, com folhas ricas em óleos essenciais que possuem atividades biológicas significativas. Avaliamos o efeito do óleo essencial de L. grata (OELG) como aditivo alimentar sobre o crescimento, índices somáticos e parâmetros bioquímicos de juvenis (5,
Acta Amazonica. Publicado em: 2022
-
12. Utilization of the Corncob Agro-Industrial Residue as a Potential Adsorbent in the Biosorption of Bisphenol-A
The presence of plastic waste in water bodies has led to a growing concern due to the impact on human health. Among the most important plastic additive molecules is bisphenol-A (BPA). On the other hand, micro-pollutant removal processes that make use of agro-industrial waste have aroused the interest of researchers. This is because the accumulation of lignoc
J. Braz. Chem. Soc.. Publicado em: 2021-07