X Ray Microtomography
Mostrando 1-12 de 26 artigos, teses e dissertações.
-
1. Discrimination of pores and cracks in iron ore pellets using deep learning neural networks
Abstract The discrimination between pores and cracks is an important step in the microstructural analysis of iron ore pellets. While the porosity is fundamental during the reduction process in blast furnaces, cracks are strongly detrimental to the mechanical strength. The usual image processing tools cannot automatically discriminate between these two types
REM, Int. Eng. J.. Publicado em: 2020-06
-
2. X-ray Microtomography to Quantify Morphological Sandstones Properties
Abstract The sandstones of the Furnas Formation in the State of Paraná, south of Brazil, are located in regions with great importance due to the natural heritage found in the rocky forms and associated flora and fauna. This paper presents a detailed analysis of the internal structure of diverse sandstones of the Furnas Formation. X-ray microtomography allow
Braz. arch. biol. technol.. Publicado em: 12/08/2019
-
3. X-ray microtomography in comparison to radiographic analysis of mechanically damaged maize seeds and its effect on seed germination
ABSTRACT. Among the most relevant aspects of seed production, mechanical damage may affect seed germination and reduce health and vigor. This study introduces a noninvasive high-resolution imaging procedure for evaluating the mechanical damage to maize seeds and the effects on seed germination. Seeds with different levels of mechanical damage were evaluated
Acta Sci., Agron.. Publicado em: 28/03/2019
-
4. Porosity Characterization of Iron Ore Pellets by X-Ray Microtomography
This work proposes a three-dimensional methodology to characterize porosity in iron ore pellets by X-ray Microtomography (microCT). An image analysis routine was developed to discriminate and quantify open/closed porosity. The results were compared to the traditional techniques of mercury intrusion porosimetry (MIP) and optical microscopy (OM). As expected,
Mat. Res.. Publicado em: 22/01/2018
-
5. Evaluation of Filler Effects on the Dynamic Mechanical Behavior of HTPB-Elastomer Used as Binder in Exemplary Composite Formulations
ABSTRACT: This study aims to evaluate the dynamic mechanical properties of a binder, used in composite propellants, with increasing amount of different solid fillers. Dynamic Mechanical Analysis (DMA) is performed to determine the region of glass-rubber transition temperature (Tg). Further parameters were obtained from the description of the loss factor curv
J. Aerosp. Technol. Manag.. Publicado em: 2017-09
-
6. Analyzing the compressive behavior of porous Ti6Al4V by X-ray microtomography
Samples with 40% vol. of pores and a pore size distribution between 100 and 500 µm were produced by powder metallurgy from Ti6Al4V alloy powders. Sintering was performed at 1300 °C during one hour in an inert Argon atmosphere in a vertical dilatometer. The compressive strength and the porosity of these samples was investigated before and after compression
Mat. Res.. Publicado em: 21/08/2017
-
7. Misfit and fracture load of implant-supported monolithic crowns in zirconia-reinforced lithium silicate
Abstract Zirconia-reinforced lithium silicate (ZLS) is a ceramic that promises to have better mechanical properties than other materials with the same indications as well as improved adaptation and fracture strength. Objective In this study, marginal and internal misfit and fracture load with and without thermal-mechanical aging (TMA) of monolithic ZLS and
J. Appl. Oral Sci.. Publicado em: 2017-06
-
8. A new species of Hoplomyzon (Siluriformes: Aspredinidae) from Maracaibo Basin, Venezuela: osteological description using high-resolution computed microtomography of a miniature species
ABSTRACT A new miniature species of banjo catfish of the genus Hoplomyzon is described from the Lake Maracaibo Basin in Venezuela. The new species is distinguished from all its congeners by the straight anterior margin of the mesethmoid (vs. a medial notch); a smooth and straight ventral surface of the premaxilla (vs. presence of bony knobs on the ventral su
Neotrop. ichthyol.. Publicado em: 30/03/2017
-
9. ACIDIC REMOVAL OF METALS FROM FLUIDIZED CATALYTIC CRACKING CATALYST WASTE ASSISTED BY ELECTROKINETIC TREATMENT
AbstractOne of the main uses of catalysts in the oil industry is in the fluidized catalytic cracking process, which generates large quantities of waste material after use and regeneration cycles and that can be treated by the electrokinetic remediation technique, in which the contaminant metals are transported by migration. In this study, deactivated FCC cat
Braz. J. Chem. Eng.. Publicado em: 2015-06
-
10. Two and three-dimensional morphometric analysis of trabecular bone using X-ray microtomography (µCT)
INTRODUCTION: Trabecular bones have a porous microstructure and can be modeled as linear elastic solids, heterogeneous and anisotropic. In the literature, few investigations have compared the two- dimensional (2D) and three-dimensional (3D) morphometric analyses of cancellous bone. METHODS: In this investigation eighteen cylindrical samples of cancellous bon
Rev. Bras. Eng. Bioméd.. Publicado em: 2014-06
-
11. Estudo da regeneração óssea guiada em mandíbula de ratos idosos / Advanced age impairs guided bone regeneration: a study in rat jaw model
Atualmente há um número crescente de idosos necessitando reabilitação com enxerto ósseo, no entanto pouco se sabe sobre o efeito do envelhecimento fisiológico sobre este processo. Este estudo teve como objetivo comparar a regeneração óssea guiada na mandíbula de ratos adultos e velhos. Ratos Wistar machos, com 9 meses (adultos) e 20 meses (velhos)
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 01/10/2012
-
12. Scaffolds baseados em nanopartículas de fosfatos de cálcio para engenharia tecidual óssea / Scaffolds based on calcium phosphate nanoparticles for bone tissue engineering
Tissue engineering associated with nanotechnology stood out because of its multidisciplinarity and results, in addition to targeting many areas of study in the field of regenerative medicine. For the process of bone regeneration to occur in appropriate form, the injured area must be organized. The reorganization of the 3D structure in the affected area shoul
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 13/07/2012