Vulcanization
Mostrando 1-12 de 28 artigos, teses e dissertações.
-
1. Sustainable blends of LDPE/NR and sugarcane bagasse ashes with PE-g-MA thermomechanical relationships
RESUMO As blendas poliméricas obtidas com resíduos que antes eram chamados de lixos vêm crescendo como uma solução viável, permitindo melhorias nas propriedades mecânicas e como alternativas sustentáveis. Este trabalho relata os efeitos de misturas de polietileno de baixa densidade (PEBD) e borracha natural(NR), com cinzas de bagaço de cana-de-açú
Matéria (Rio J.). Publicado em: 16/09/2019
-
2. Production of Medical Grade Silicone for Facial Prosthesis with Bactericidal Properties from the Inclusion of Poly (Diallyldimethylammonium Chloride): An in Vitro Study
Abstract Objective: To evaluate the inclusion capacity and bactericidal efficiency of diallyl dimethyl ammonium chloride (PDADMAC) diluted in tetrahydrofuran (THF) upon inclusion in the medical grade silicone polymer structure. Material and Methods: It was diluted the PDADMAC in THF at the concentration of 4wt%. It was included in the silicon paste during
Pesqui. Bras. Odontopediatria Clín. Integr.. Publicado em: 02/09/2019
-
3. Cellulose Nanocrystals and Jute Fiber-reinforced Natural Rubber Composites: Cure Characteristics and Mechanical Properties
A comparative study was conducted for three natural rubber (NR) composites: one containing raw jute fibers, one containing bleached jute fibers, and one containing cellulose nanocrystals (CNCs). The composites were prepared by adding each filler at 5 or 10 phr to the latex before chemical coagulation, and the composites were processed in a two-roll mixing mi
Mat. Res.. Publicado em: 26/08/2019
-
4. Effects of Rotor Speed on Peroxide/Bismaleimide Cured Polypropylene/Nitrile Rubber Thermoplastic Vulcanizates (TPVs)
Elastomer thermoplastics are a class of polymeric materials that received industry attention due to the possibility of joining the elastic of elastomers with the thermoplastics processability. The synergistic properties are linked to the appropriate processing. This study evaluated the effect of rotor speed during polymer mixing and the dynamic vulcanization
Mat. Res.. Publicado em: 09/08/2018
-
5. The Influence of Bleached Jute Fiber Filler on the Properties of Vulcanized Natural Rubber
There is growing interest in replacing the synthetic reinforcements used for natural rubber (NR) composites with natural fibers from renewable, environmentally sustainable sources. Jute fibers may be suitable reinforcements for NR because they have a high tensile strength, which is comparable to other fillers such as glass fibers. Thus, we studied the incorp
Mat. Res.. Publicado em: 30/10/2017
-
6. Devulcanization of Natural Rubber in Composites with Distinct Crosslink Densities by Twin-Screw Extruder
In this study, the effects of the devulcanization process realized by an intermeshing co-rotating twin-screw extruder (ICTSE) on three vulcanized Natural Rubber (NR) composites with different crosslink densities (CD) have been investigated. The extrusion parameters were fixed, as well as the initial material granulometry and auxiliary thermoplastic added to
Mat. Res.. Publicado em: 02/05/2017
-
7. SÍNTESE E CARACTERIZAÇÃO DE NOVOS ORGANOMETÁLICOS DE ESTANHO (IV) COM LIGANTES DITIOCARBIMATOS E SUA AÇÃO ACCELERADORA NA VULCANIZAÇÃO DE BORRACHA NITRÍLICA
This paper describes the synthesis of four new organotin compounds of general formula: (Ph4P)[Sn(Cy)3(RSO2N=CS2)] [Ph4P = tetraphenylphosphonium cation, Cy = cyclohexyl, R = C6H5 (1), 4-ClC6H4 (2), 4-BrC6H4 (3) and 4-IC6H4 (4)]. They were obtained by the reaction between four different potassium N-R-sulfonyldithiocarbimate salts and tricyclohexyltin chloride
Quím. Nova. Publicado em: 2016-08
-
8. Sugarcane bagasse ash: new filler to natural rubber composite
Waste recycling has been the subject of numerous scientific researches regarding the environmental care. This paper reports the redirecting of sugarcane bagasse ash (SBA) as new filler to natural rubber (NR/SBA). The NR/SBA composites were prepared using an opened cylinder mixer to incorporate the vulcanization agents and different proportions of residue (SB
Polímeros. Publicado em: 2014-12
-
9. Characterization of additives typically employed in EPDM formulations by using FT-IR of gaseous pyrolyzates
In this study, Fourier transform infrared spectroscopy (FT-IR) was employed to investigate the gaseous pyrolysis products of ethylene - propylene - diene rubber (EPDM). The objective was to evaluate the potential of FT-IR analysis of gaseous pyrolyzates (PY-G/FT-IR) for characterization of EPDM additives. Two EPDM formulations, containing additives typically
Polímeros. Publicado em: 27/05/2014
-
10. Líquidos iônicos como plastificantes em blendas de borracha nitrílica/polianilina
Two imidazolium-based ionic liquids (C4MIMTf2N and C4MIMBF4) were used to verify their influence on polyaniline (PANI) and nitrile rubber (NBR)/PANI blend properties and the vulcanization process. High conductivity values were observed for PANI-C4MIMTf2N samples and no interference was found for the C4MIMBF4 samples. These materials were added to NBR by mech
Quím. Nova. Publicado em: 2014
-
11. Compatibilization efficiency of carboxylated nitrile rubber and epoxy pre-polymer in nitrile/acrylic rubber blends
An investigation has been made of the effects from a compatibilizer, viz. carboxylated nitrile rubber (XNBR), on several properties of nitrile rubber (NBR) and acrylic rubber (ACM) blends, including curing characteristics, mechanical, dynamic mechanical and dielectric properties. The presence of XNBR until 10 phr resulted in an improvement of the ultimate te
Polímeros. Publicado em: 05/04/2013
-
12. Thermal and rheological behavior of reactive blends from metallocene olefin elastomers and polypropylene
Reactive blends of metallocene polyolefin elastomers (POE)/polypropylene (PP) with 60/40 composition were prepared with an organic peroxide, 2,5-dimethyl-2,5-di-(t-butylperoxy)hexane, and a bis-azide derivative, diphenyloxid-4,4'-bis(sulfonylazide) (BSA). Ethylene-1-butene (EB) and ethylene-1-octene (EO) copolymers and elastomeric polypropylene (ePP) were us
Polímeros. Publicado em: 05/06/2012