Viscoplastic
Mostrando 1-12 de 36 artigos, teses e dissertações.
-
1. Rheology of mine tailings deposits for dam break analyses
Abstract This article deals with the rheology of tailings deposits related to dam break analysis. The material used was a fine tailings from iron ore processing. Geotechnical and rheological characterization of these tailings were performed. The rheological characterization consisted of rotational and oscillatory tests. It was observed that the rheological p
REM, Int. Eng. J.. Publicado em: 2021-06
-
2. NUMERICAL STUDY OF VISCOPLASTIC FLOW IN A T-BIFURCATION: IDENTIFICATION OF STAGNANT REGIONS
Abstract Identification of stagnant regions of viscoplastic fluid flows in production lines and equipment is of paramount importance owing to potential material degradation and process contamination. The present work introduces an assessment strategy to identify, classify and quantify unyielded regions with the objective of optimizing the flow conditions wit
Braz. J. Chem. Eng.. Publicado em: 09/12/2019
-
3. Hardening and Dynamic Recovery During Hot Compression Test of Copper Simulated as Viscoplastic Material
The Norton-Bailey equation was used to simulate by finite elements the hardening and dynamic recovery of copper during the hot compression tests. The constants of Norton-Bailey equation were determined from the Voce-Kocks model. The simulation assumes a Mortar Contact with Coulomb friction and axial symmetry. Numerical results were compared with experiments.
Mat. Res.. Publicado em: 05/12/2019
-
4. Analytical solution of circular tunnel in elastic-viscoplastic rock mass
Abstract This paper deals with a deep circular tunnel excavated in infinite homogeneous and isotropic elasto-viscoplastic rock mass subjected to a hydrostatic initial stresses. The tunnel is divided into the initial plastic, viscoplastic, and elastic zones. By combining the generalized Bingham model with Mohr-Coulomb yield criteria, analytical solutions of t
Lat. Am. j. solids struct.. Publicado em: 29/07/2019
-
5. A Two-Surface Viscoplastic Model for the Structural Steel
Abstract As extension of the previous two-surface model in plasticity, a two-surface model for viscoplasticity is presented herein. In order to validate and investigate the performance of the proposed model, several numerical simulations are undertaken especially for structural steel under monotonic and cyclic loading cases, where experimental results and nu
Lat. Am. j. solids struct.. Publicado em: 2017-06
-
6. Matrix consolidation mechanism in 1D-Ti/SiC/C composites produced by continuous binder-powder coating
In this workmatrix consolidation mechanism has been investigated in 1D-Ti/SiC/C composites produced by Continuous Binder-Powder Coating - CBPC. Titanium metal matrix composites reinforced with continuous SiC/C filaments were analysed in different densification conditions. The results show that during processing, densification occurs by several mechanisms inc
Mat. Res.. Publicado em: 28/01/2013
-
7. Aproximações estabilizadas de escoamentos de fluidos viscoplásticos através de uma expansão seguida de uma contração axissimétrica
The effect of inertia in the flow of viscoplastic fluids through an expansion followed by a contraction is analyzed. The mechanical behavior is modeled by the Generalized Newtonian Fluid constitutive equation, with the viscosity function given by the SMD equation (de Souza Mendes and Dutra, 2004). The conservation equations of mass and momentum, together wit
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 2012
-
8. RESTARTABILITY OF VISCOPLASTIC MATERIALS IN PIPES / REINÍCIO DE ESCOAMENTO DE MATERIAIS VISCOPLÁSTICOS EM UM TUBO
On of the main problems in the operation of subsea pipelines that convey paraffin oils is the flow startup after long stoppages. Along the path from the reservoir to the platform, the oil experiences significant heat losses, especially to the low-temperature water at the sea bottom. When there is no flow, the oil may reach very low temperatures. Cooling indu
Publicado em: 2011
-
9. Modelagem mecânica e investigação numérica de escoamentos de fluidos SMD empregando um método multi-campos de galerkin mínimos-quadrados
A maioria dos líquidos encontrados na natureza são não-Newtonianos e o estudo do seu comportamento tem uma importância significante em diferentes áreas da engenharia. Entre eles, uma larga classe de materiais que exibem pequena ou nenhuma deformação quando sujeitos a um nível de tensões inferiores a uma tensão limite de escoamento – chamado de co
Publicado em: 2011
-
10. A numerical investigation of inertia flows of Bingham-Papanastasiou fluids by an extra stress-pressure-velocity galerkin least-squares method
This article is concerned with finite element approximations for yield stress fluid flows through a sudden planar expansion. The mechanical model is composed by mass and momentum balance equations, coupled with the Bingham viscoplastic model regularized by Papanastasiou (1987) equation. A multi-field Galerkin least-squares method in terms of stress, velocity
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2010-12
-
11. Escoamento de fluídos pseudoplásticos e viscoplásticos: avaliação analítica e aproximação por elementos finitos / Pseudoplastic and viscoplastic fluids flow: analitic avaliation and finit element aproximation
O presente trabalho objetiva a investigação teórica e numérica da dinâmica dos escoamentos dos fluidos industriais. A grande maioria destes fluidos, ao escoarem apresentam um comportamento reológico bem diverso dos apresentados pelos líquidos Newtonianos - sendo, portanto, conhecidos na literatura como fluidos não-Newtonianos. Neste trabalho são des
Publicado em: 2010
-
12. Efeito dos materiais do backing bar na geometria e dureza de juntas soldadas por FSW em ligas de alumínio 6013 e 2024
Solid-state joining techniques such as Friction Stir Welding (FSW) are a natural choice to produce weld low heat input, limited slight distortion and low microstructural and mechanical degradation. Great effort has currently been devoted to the joining of Al-Cu-Mg and the Al-Mg-Si alloys because of their high strength, improved formability, and application i
Publicado em: 2009