Veneer
Mostrando 13-24 de 42 artigos, teses e dissertações.
-
13. Inorganic filler content of resin-based luting agents and the color of ceramic veneers
Abstract The influence of inorganic filler content of resin-based luting agents (RBLAs) on color change (ΔE00), CIEL*a*b* (individual color coordinates), and translucency parameters (TP) of simulated ceramic laminate veneer (CLV) was investigated. RBLAs with low, intermediate, and high inorganic filler content (55%, 65%, and 75% mass fractions, respectively
Braz. oral res.. Publicado em: 07/06/2018
-
14. Influence of Photoinitiator on Accelerated Artificial Aging and Bond Strength of Experimental Resin Cements
Resumo O objetivo deste estudo foi avaliar in vitro o efeito do fotoiniciador fenilpropanodiona (PPD), isoladamente ou em associação com a CQ, sobre a estabilidade de cor de cimentos resinosos fotoativados e sua resistência de união adesiva à cerâmica, por teste de microcisalhamento. Foram utilizados 4 cimentos resinosos, sendo um comercial (RelyX Vene
Braz. Dent. J.. Publicado em: 2018-02
-
15. Effect of Ceramic Interposition and Post-activation Times on Knoop Hardness of Different Shades of Resin Cement
Resumo O objetivo deste estudo foi avaliar a dureza Knoop de diferentes cores de um cimento resinoso fotoativado diretamente ou através da interposição de um disco de cerâmica, medindo 15 min ou 24 h após exposição à luz, em diferentes profundidades. Amostras do cimento resinoso (Variolink Veneer) em sete cores foram fabricados num molde de elastôme
Braz. Dent. J.. Publicado em: 2018-02
-
16. The marginal fit of lithium disilicate crowns: Press vs. CAD/CAM
Abstract: This study aimed to compare the vertical marginal gap of teeth restored with lithium disilicate crowns fabricated using CAD/CAM or by pressed ceramic approach. Twenty mandibular third molar teeth were collected after surgical extractions and prepared to receive full veneer crowns. Teeth were optically scanned and lithium disilicate blocks were used
Braz. oral res.. Publicado em: 22/01/2018
-
17. Pre-sintered Y-TZP sandblasting: effect on surface roughness, phase transformation, and Y-TZP/veneer bond strength
Abstract Sandblasting is a common method to try to improve the Y-TZP/veneer bond strength of dental prostheses, however, it may put stress on zirconia surfaces and could accelerate the t→m phase transformation. Y-TZP sandblasting before sintering could be an alternative to improve surface roughness and bonding strength of veneering ceramic. Objectives. Th
J. Appl. Oral Sci.. Publicado em: 2017-12
-
18. Citotoxicidade de três cimentos resinosos fotopolimerizáveis sobre fibroblastos 3T3
Resumo Introdução Cimentos resinosos fotopolimerizáveis são materiais de eleição para a cimentação de facetas laminadas. Devem ser biocompatíveis oferencendo riscos mínimos ao uso clínico em pacientes. Objetivo O objetivo desse trabalho foi avaliar in vitro a citotoxicidade de três cimentos resinosos: Variolink II (Ivoclar Vivadent), Allcem Ven
Rev. odontol. UNESP. Publicado em: 10/08/2017
-
19. Effect of the Cooling Rate on the Properties of Veneer Porcelain for Zirconia Dental Prosthesis
To solve chipping of veneer porcelain in zirconia dental prosthesis it has been studied different cooling rates in firing schedules to control residual stresses generated by differences in thermal properties between the ceramics. However, cooling rates may affect the porcelain, irrespectively of interaction with zirconia. This study analyzed the effect of co
Mat. Res.. Publicado em: 07/08/2017
-
20. Degree of conversion and bond strength of resin-cements to feldspathic ceramic using different curing modes
Abstract Resin cements have led to great advances in dental ceramic restoration techniques because of their ability to bond to both dental structures and restorative materials. Objective The aim of this study was to assess the performance of resin cements when different curing modes are used, by evaluating the degree of conversion and bond strength to a ce
J. Appl. Oral Sci.. Publicado em: 2017-02
-
21. Production and Properties of a New Wood Laminated Veneer/High-Density Polyethylene Composite Board
AbstractThe paper aimed at evaluating the feasibility and the properties of a new product which combines wood veneer and high-density polyethylene (HDPE) from post-consuming plastic bags. Three HDPE amounts were evaluated: 150g/m2, 250 g/m2 e 350 g/m2. The boards were manufactured using a single-opening hot-press under such conditions: 140ºC, for 20 minutes
Mat. Res.. Publicado em: 2015-10
-
22. Influência de diferentes combinações de lâminas de Eucalyptus saligna e Pinus taeda em painéis LVL
Investigou-se a influência do posicionamento de lâminas de madeira de Eucalyptus saligna e Pinus taeda nas camadas de painéis Laminated Veneer Lumber (LVL). As composições foram manufaturadas em seis diferentes combinações de cinco lâminas de 3,2 mm de espessura, coladas com adesivo fenol-formaldeído, resultando em tratamentos compostos de madeira d
Ciênc. Florest.. Publicado em: 2015-03
-
23. Strength of 3Y-TZP and feldspathic porcelain subjected to different cooling methods
AIM: To investigate the effect of the cooling rate on flexural strength of monolayer and bilayer porcelain/zirconia (Y-TZP) bars. METHODS: Forty-five specimens were made for each design group: (PM) monolithic specimens of veneer porcelain Vita VM9 (Vita, Germany); (ZM) monolithic specimens of zirconia (ZiHP; ProtMat, Brazil); (PB) bilayer specimens zir
Braz. J. Oral Sci.. Publicado em: 2014-04
-
24. Degree of Conversion of a Resin Cement Light-Cured Through Ceramic Veneers of Different Thicknesses and Types
Durante a cimentação de facetas cerâmicas, a polimerização de cimentos resinosos pode ser comprometida se a cerâmica atenuar a irradiância do aparelho fotopolimerizador. O objetivo deste estudo foi avaliar o efeito de diferentes tipos e espessuras de facetas cerâmicas sobre o grau de conversão de um cimento resinoso fotopolimerizável (RelyX Veneer)
Braz. Dent. J.. Publicado em: 2014-01