Ultrasonic Testing
Mostrando 1-12 de 29 artigos, teses e dissertações.
-
1. Estimação da profundidade de fissuras em concreto através da velocidade de ondas ultrassônicas
RESUMO As fissuras são as manifestações patológicas mais recorrentes no concreto, devido as diferentes formas de exposição que o material está sujeito. Neste cenário, é importante que as edificações passem por inspeções através de diferentes métodos, dentre os quais os ensaios não destrutivos (END) aparecem como ferramenta alternativa. Dentre
Matéria (Rio J.). Publicado em: 25/11/2019
-
2. Tempo de Voo da Onda Difratada (ToFD) Auxilia na Garantia da Qualidade da Produção de Peças e Estruturas Mecânicas
Resumo A Técnica Tempo de Voo da Onda Difratada (ToFD) é uma técnica de ensaio não destrutivo por ultrassom utilizada para a detecção de falhas e descontinuidades em diferentes componentes, garantindo a qualidade, confiabilidade e segurança. É amplamente utilizada na indústria, principalmente na avaliação de peças e estruturas mecânicas. É lar
Soldag. insp.. Publicado em: 14/11/2019
-
3. Mejora en la calidad de imágenes ultrasónicas aplicando métodos de composición espacial y empleando sistemas de Phased Array
ABSTRACT The Phased Array Ultrasonic Technique (PAUT) has become a widely used imaging tool for the Nondestructive Testing in the industrial field. The PAUT allows making deflections and focusing the ultrasound beam at different depths within the material, through an electronic control of each one of the N elements that make up the array transducer. Thus, se
Matéria (Rio J.). Publicado em: 19/07/2018
-
4. Nondestructive ultrasonic testing in rod structure with a novel numerical Laplace based wavelet finite element method
Abstract Rod structure has been widely used in aerospace engineering and civil engineering. Nondestructive testing is a very important method applied to detect unseen flaws in structures, ultrasonic wave nondestructive testing has been used in many areas. Finite Element Method is one of the most widely used numerical methods but would have a high cost when d
Lat. Am. j. solids struct.. Publicado em: 16/07/2018
-
5. Push-out bond strength of different tricalcium silicate-based filling materials to root dentin
Abstract: The aim of this study was to evaluate the bond strength of different triccalcium silicate cements to retrograde cavity using a push out test. Thirty maxillary central incisors were shaped using #80 hand files and sectioned transversally. Root slices were obtained from the apical 4 mm after eliminating the apical extremity. The specimens were embedd
Braz. oral res.. Publicado em: 08/03/2018
-
6. Monitoring Heat Treatments in Steels by a Non Destructive Ultrasonic Method
In order to determine if heat treatments can be discerned by nondestructive ultrasonic testing, samples of SAE 1045 and SAE 4140 steels were subjected to the classical heat treatments of annealing, normalizing, quenching, and quenching and tempering, and their elastics constants, Young's, shear and Poisson's moduli, were monitored by ultrasound. Results show
Mat. Res.. Publicado em: 24/08/2017
-
7. Controlled Pre-Corrosion Attack and Ultrasonic Fatigue Endurance of Titanium Alloy Ti-6Al-4V
Abstract Ultrasonic fatigue tests were carried out on titanium alloy Ti-6Al-4V on the base material and the pre-corroded specimen to assess the pre-corrosion effect on the fatigue life of this alloy. The pre-corrosion was obtained by immersion of specimens in an acid solution: hydrochloric acid with 1.4 of pH during 8 and 16 minutes. All ultrasonic fatigue t
Lat. Am. j. solids struct.. Publicado em: 2017-03
-
8. Rheological behavior of acrylic paint blends based on polyaniline
Abstract The rheological properties of acrylic paints and polyaniline (PAni) blends, with different contents of PAni doped by dodecyl benzene sulphonic acid (DBSA) and, dispersed by mechanical stirrer and ultrasonic, were investigated by controlled shear rate testing ramps. The results showed that the commercial acrylic paint had tended to deliver the requir
Polímeros. Publicado em: 18/08/2016
-
9. A flexible multichannel FPGA and PC-Based ultrasound system for medical imaging research: initial phantom experiments
IntroductionIn this paper, we present the initial results of a fully programmable 128-channel FPGA and PC-based system that has been developed for medical ultrasound (US) imaging research in our University laboratory (Federal University of Technology - Paraná, Brazil).MethodsIn order to demonstrate the feasibility of the US research system, two applications
Res. Biomed. Eng.. Publicado em: 29/09/2015
-
10. Mechanical and thermal behavior of polyvinyl alcohol reinforced with aligned carbon nanotubes
ABSTRACTIn recent years, due to their high specific mechanical properties, the polymer matrix composites have been widely used. In particular, carbon nanotubes (CNTs) have been used as reinforcement due to its exceptional mechanical and electrical properties. In this work the mechanical behavior of polyvinyl alcohol (PVA) reinforced with different percentage
Matéria (Rio J.). Publicado em: 2015-09
-
11. Micro-shear bond strength and surface micromorphology of a feldspathic ceramic treated with different cleaning methods after hydrofluoric acid etching
Objective: The aim of this study was to evaluate the effect of feldspathic ceramic surface cleaning on micro-shear bond strength and ceramic surface morphology. Material and Methods: Forty discs of feldspathic ceramic were prepared and etched with 10% hydrofluoric acid for 2 minutes. The discs were randomly distributed into five groups (n=8): C: no tre
J. Appl. Oral Sci.. Publicado em: 2014-04
-
12. Simulação da propagação de ondas ultrassônicas longitudinais em materiais estruturais aeroespaciais / Simulating the propagation of longitudinal ultrasonic waves in aerospace structural materials
The use of composite materials in the aerospace industry is increasing due to its low ratio between density and mechanical strength. To perform non-destructive testing using ultrasound, it is necessary to know the sound velocity in these materials. It is not always possible to manufacture physical prototypes during the development of a project because of tim
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 10/08/2012