Top Cross
Mostrando 13-24 de 85 artigos, teses e dissertações.
-
13. Analog Models of Flanking Structures and a Natural Example in the Quadrilátero Ferrífero, Minas Gerais
ABSTRACT The aim of this study is to present analog models of flanking structures and to analyze the Fábrica Nova synform, Quadrilátero Ferrífero, Minas Gerais, from a geometric point of view. We set up seven models using a linear viscous silicone and produced flanking structures with a shear velocity of 2 cm h-1. At different initial orientations with re
An. Acad. Bras. Ciênc.. Publicado em: 31/07/2017
-
14. Experimental Study of the Compressive Strength of Multi-Coat Renders
Mortar compressive strength is a standard requirement and should be tested on stand-ardized specimens with a 40 mm square cross section. However, these specimens with only one type of mortar (base-coat layer) do not represent the render traditionally ap-plied to façades since that must consist of at least two layers (base coat and top coat, with different f
Mat. Res.. Publicado em: 13/07/2017
-
15. Heterose e capacidade de combinação de traços fisiológica qualidade de single cross Vs. a três híbridos de sorgo
RESUMO. O objetivo desta pesquisa foi comparar parâmetros genéticos para características relacionadas com germinação das sementes e vigor de plântulas de cruzamentos simples (SCH) vs. três vias (TWH) híbridos de sorgo. O estudo foi realizado em substrato a base de areia em estufa; 67 genótipos (4 pares de linhas A- e B-, 4 linhas R-, 13 SCH e 42 TWH
Acta Sci., Agron.. Publicado em: 2017-06
-
16. Impact analysis of critical success factors on the benefits from statistical process control implementation
Abstract The Statistical Process Control - SPC is a set of statistical techniques focused on process control, monitoring and analyzing variation causes in the quality characteristics and/or in the parameters used to control and process improvements. Implementing SPC in organizations is a complex task. The reasons for its failure are related to organizational
Prod.. Publicado em: 02/03/2017
-
17. Capacidade combinatória de linhagens recombinadas de mamoeiro oriundas de retrocruzamento para conversão sexual
RESUMO Os objetivos deste trabalho foram gerar estimativas de capacidade combinatória de 22 linhagens de mamoeiro com testadores do grupo 'Solo' e 'Formosa' em esquema de top cross e identificar híbridos agronomicamente superiores. As linhagens foram selecionadas em gerações de retrocruzamentos para conversão sexual, tendo como genitor recorrente, o gen
Rev. Ciênc. Agron.. Publicado em: 2017-03
-
18. Poly(Vinyl Alcohol) Gate Dielectric Treated With Anionic Surfactant in C60 Fullerene-Based n-Channel Organic Field Effect Transistors
We report on the preparation and performance enhancement of n-type low-voltage organic field effect transistors (FETs) based on cross-linked poly(vinyl alcohol) (cr-PVA) as gate dielectric and C60 fullerene as channel semiconductor. Transistors were prepared using bottom-gate top-contact geometry and exhibited field-effect mobility (µFET) of 0.18 cm2V-1s-1.
Mat. Res.. Publicado em: 19/09/2016
-
19. Bending, Vibration and Buckling of Laminated Composite Plates Using a Simple Four Variable Plate Theory
Abstract In the present study, a simple trigonometric shear deformation theory is applied for the bending, buckling and free vibration of cross-ply laminated composite plates. The theory involves four unknown variables which are five in first order shear deformation theory or any other higher order theories. The in-plane displacement field uses sinusoidal fu
Lat. Am. j. solids struct.. Publicado em: 2016-03
-
20. Produtividade do minimilho em função das adubações nitrogenada e potássica
Há grande carência de informações quanto à adubação com Nitrogênio e Potássio para a produção de minimilho. Quando colhido antes do início da formação de grãos, as quantidades de nutrientes exigidas podem ser diferenciadas. Por essa razão, o presente trabalho teve por objetivo avaliar a resposta do minimilho às adubações nitrogenada e pot�
Rev. Ceres. Publicado em: 2014-02
-
21. Thermal flexural analysis of cross-ply laminated plates using trigonometric shear deformation theory
Thermal stresses and displacements for orthotropic, two-layer antisymmetric, and three-layer symmetric square cross-ply laminated plates subjected to nonlinear thermal load through the thickness of laminated plates are presented by using trigonometric shear deformation theory. The in-plane displacement field uses sinusoidal function in terms of thickness co-
Lat. Am. j. solids struct.. Publicado em: 2013-09
-
22. Flexural analysis of cross-ply laminated beams using layerwise trigonometric shear deformation theory
In the present work, a layerwise trigonometric shear deformation theory is used for the analysis of two layered (90/0) cross ply laminated simply supported and fixed beams subjected to sinusoidal load. The displacement field of the present theory consists of trigonometric sine function in terms of thickness coordinate to take into account the effect of trans
Lat. Am. j. solids struct.. Publicado em: 2013-07
-
23. Divergência genética em genótipos de milho, no estado do Tocantins
Este trabalho objetivou avaliar a divergência genética em genótipos de milho no sul do estado do Tocantins. O experimento foi realizado no município de Gurupi - TO. As populações foram obtidas de 70 híbridos top cross pelo cruzamento de linhagens S6 com um testador, utilizando-se 11 cultivares como testemunha, totalizando 81 genótipos. O delineamento
Revista Ciência Agronômica. Publicado em: 2012-09
-
24. Avaliacao genotipica de progenies de meios-irmaos do composto dentado (Zea mays L.) para condicoes de safrinha.
O presente trabalho foi conduzido na FCAV-UNESP, Campus de Jaboticabal, na safrinha do ano agricola de 1991. Foram avaliados 100 progenies de hibridos interpopulacionais obtidos do cruzamento em top-cross entre as populacoes do Composto Dentado e Composto Flint. Os caracteres analisados foram: danos de Spodoptera frugiperda, dias ate o florescimento, altura
Pesquisa Agropecuaria Brasileira. Publicado em: 2011