Thermal Recovery
Mostrando 1-12 de 160 artigos, teses e dissertações.
-
1. Novel Design of a Hybrid Superconducting Fault Current Limiter with Controlled Solid-State Device
Abstract Fault current limiters are essential devices used to protect the power system and its equipment against high levels of fault current, which are growing up due to the increase of new power sources. This paper proposes a novel design of a Hybrid Superconducting Fault Current Limiter (Hybrid SFCL), which is composed basically by thyristors in series wi
J. Microw. Optoelectron. Electromagn. Appl.. Publicado em: 2021-06
-
2. On the Use of a TiO2 Sol-Gel for Horseradish Peroxidase Enzyme Immobilization for Development of an Amperometric Biosensor
The sol-gel technique has drawn considerable attention in the area of biomolecules immobilization by virtue of its intrinsic properties including chemical inertness, thermal stability, and good biocompatibility. The present work reports the development of a bio-sensing methodology which involves the immobilization of horseradish peroxidase enzyme (HRP) on pe
J. Braz. Chem. Soc.. Publicado em: 2021-06
-
3. Development and Validation of a Gas Chromatographic Method for the Quantification of Minor Alkaloids in Cocaine
The quantification of minor alkaloids in seized cocaine can provide information for drug profiling and law enforcement initiatives. This work presents the development and validation of an analytical method to quantitate minor alkaloids in cocaine samples using gas chromatography with flame ionization detector, after derivatization. The method was validated i
J. Braz. Chem. Soc.. Publicado em: 2021-04
-
4. DISRUPTION OF Nannochloropsis gaditana (EUSTIGMATOPHYCEAE) RIGID CELL WALL BY NON-THERMAL PLASMA PRIOR TO LIPID EXTRACTION AND ITS EFFECT ON FATTY ACID COMPOSITION
Abstract This study assessed the effect of non-thermal plasma (NTP) on Nannochloropsis gaditana cell rupture and subsequent lipid extraction. Micrograph images showed that the surface of original N. gaditana cells appeared smooth and had no apparent holes, whereas after NTP the cells showed a non-uniform apparently fractured surface with many pores and large
Braz. J. Chem. Eng.. Publicado em: 13/01/2020
-
5. Avaliação energética de um edifício de serviços: Escola Superior Aveiro Norte, Portugal
Resumo O objetivo deste trabalho é realizar uma avaliação energética da Escola Superior Aveiro Norte (ESAN), situada no município de Oliveira de Azeméis (Portugal). Esse edifício possui tecnologias de climatização pouco convencionais em Portugal, como bombas de calor geotérmicas associadas a piso radiante e ventilação, com pré-aquecimento de ar,
Ambient. constr.. Publicado em: 03/10/2019
-
6. Análise da geração de energia elétrica por meio da utilização de conversores do tipo TEG em lingotamento contínuo de aços
RESUMO A fabricação do aço é um processo que requer enormes quantidades de recursos, como por exemplo combustíveis, minério de ferro, carvão, entre outros. Com a crescente preocupação com o meio ambiente, seja pelas cargas ambientais ou pelo aquecimento global, cresce também a necessidade do desenvolvimento de novas tecnologias que possibilitem um
Matéria (Rio J.). Publicado em: 16/09/2019
-
7. Effect of Processing Parameters on Hot Deformation Behaviour and Microstructural Evolution of PM Ti-5553 Alloy at a Moderate-high Strain Rate
Isothermal compression tests of Ti-5553 (Ti-5Al-5V-5Mo-3Cr) alloy, produced by a fast consolidation approach from blended elemental powder mixture, were performed on a Gleeble® 3800 thermal-physical simulator to investigate its hot deformation behaviour. The samples were compressed in a wide temperature range from 700 ºC to 1150 ºC and a moderate-high str
Mat. Res.. Publicado em: 10/06/2019
-
8. Damping of Fe-Al Alloy Electrodeposited in an Ionic Liquid
Iron-Aluminium alloys were produced by the electro-deposition of iron-aluminium on a copper substrate. The electro-deposition process was done in the ionic liquid 1-butyl-1-methylpyrrolidinium trifluoromethylsulfonate, [Py1,4]TfO. A solution of (0.2 M FeCl2 + 2.75 M AlCl3)/ [Py1,4] TfO was used at a temperature of T=363 K because this mixture is solid at roo
Mat. Res.. Publicado em: 11/10/2018
-
9. The Influence of Microstructure and Mechanical Resistance on the Shape Memory of Ecae Processed Stainless Fe-Mn-Si-Cr-Ni-Co Steel
In the current work, XRD, SEM, EBSD and TEM techniques were used to evaluate the microstructure of stainless Fe-Mn-Si-Cr-Ni-Co shape memory steel processed by ECAE and annealed for one hour at temperatures ranging from 650ºC to 950ºC. The results were then correlated with the mechanical and shape-memory properties of the steel. It was observed that the sam
Mat. Res.. Publicado em: 09/08/2018
-
10. Transition from Thermokinetic to Chemical Instabilities in a Modified Sal’nikov Model
Traditionally, thermokinetic and chemical oscillations have been studied independently, but in cellular media recent studies have shown that cell’s temperature is not uniform. Thus, on this context it is possible to inquire about the influence of thermal effects on chemical oscillatory behavior and vice versa. To this end, in this paper we propose a dynami
J. Braz. Chem. Soc.. Publicado em: 2018-07
-
11. Modification of thermal and rheological behavior of asphalt binder by the addition of an ethylene-methyl acrylate-glycidyl methacrylate terpolymer and polyphosphoric acid
Abstract This study evaluated the modification effects of adding ethylene-methyl acrylate-glycidyl methacrylate terpolymer (EMGMA) in the presence of polyphosphoric acid (PPA) to an asphalt binder graded as 50/70 (0.1mm) in the Brazilian penetration grade specification (AC 50/70). The EMGMA terpolymer has been presented as a new alternative to modify asphalt
Polímeros. Publicado em: 2017-12
-
12. Application of polyester derived from biomass in petroleum asphalt cement
Abstract This study evaluated the effects of the incorporation of a new additive to asphalt cement oil (CAP). A polyol product was obtained through the oxypropylation reaction of sugarcane bagasse. This polyol was polymerised with pyromellitic anhydride in order to obtain a polyester (BCP) to test its suitability in terms of the material properties to be app
Polímeros. Publicado em: 29/06/2017