Thermal Conductivity
Mostrando 25-36 de 276 artigos, teses e dissertações.
-
25. PHYSICAL, MECHANICAL AND THERMAL BEHAVIOR OF ADOBE STABILIZED WITH “SYNTHETIC TERMITE SALIVA”
ABSTRACT Adobe is an efficient construction material for several reasons, such as its thermal comfort, sustainability, and lower energy cost, as well as the simplicity of its production and execution. However, challenges such as water absorption, capillarity, and compressive strength should be investigated to improve its physical and mechanical properties. �
Eng. Agríc.. Publicado em: 25/04/2019
-
26. Synthetic granite composite for precision equipment structures
ABSTRACT The structure is a component that plays an extremely important role in the equipment’s performance, it must withstand efforts without compromising the function, receive and transfer heat, dampen vibrations and position the elements, as well as promote ergonomics and aesthetics. In lightweight and precision equipment’s the raw material used must
Matéria (Rio J.). Publicado em: 06/12/2018
-
27. Sustainable Glass Foams Produced from Glass Bottles and Tobacco Residue
In this work, discarded soda-lime-silica glass bottles and tobacco residue (after oil extraction to produce biodiesel) were prepared in different formulations to obtain glass foams. The formulated compositions were homogenized and uniaxially compacted at 40 MPa then fired at 850 ºC and 900 ºC for 60 min to investigate the effects of tobacco residue and tem
Mat. Res.. Publicado em: 03/12/2018
-
28. The Effect of Rapid Microwave Sintering Process on the Electrical Conductivity, Thermal Conductivity and Mechanical Properties of Al-TiC Composites
In this research, electrical conductivity, thermal conductivity and mechanical properties of the Al-TiC composites which were sintered via microwave-assisted process were investigated. The specimens were sintered for 3, 5 and 8 minutes. The results have shown that the sample which contains 4 vol. % TiC and was sintered for 8 minutes, has the highest electric
Mat. Res.. Publicado em: 11/10/2018
-
29. Study of Microstructure and Thermal Properties of the Low Melting Bi-In-Sn Eutectic Alloys
Beside their technological importance in soldering, the low melting eutectic alloys based on bismuth and indium have potential for commercial application in the field of phase-change materials (PCMs). In this respect, the knowledge of their microstructure and thermal properties such as melting temperature, latent heat of melting, supercooling tendency, therm
Mat. Res.. Publicado em: 11/10/2018
-
30. Propiedades físicas y cristalinas del Cd1-xZnxTe (0 ≤ x ≤ 1)
ABSTRACT Cd1-xZnxTe (0 ≤ x ≤ 1) and ZnTe are II-VI semiconductors, which are used in single crystalline structure to improve their crystalline and electrical properties. The CZT and ZnTe must possess high crystalline and electrical quality to be used, the first in x or γ-ray detectors, and as substrates for suitable epitaxial films for detecting IR radi
Matéria (Rio J.). Publicado em: 19/07/2018
-
31. Nafion/sulfonated poly(indene) polyelectrolyte membranes for fuel cell application
Abstract Sulfonated poly(indene) (SPInd), with 35% and 45% degree of sulfonation, was blended with Nafion to prepare blended membranes with 10, 15 and 20 wt.% of SPInd. Membranes were evaluated by infrared spectroscopy, thermogravimetric analysis, differential scanning calorimetry, scanning electron microscopy and X-ray diffraction. Water uptake (WU), ion ex
Polímeros. Publicado em: 10/07/2018
-
32. Preparation and Ablation Performance of Lightweight Phenolic Composite Material under Oxyacetylene Torch Environment
ABSTRACT The present study investigates the influence of fiber content on thermal properties of short silica fiber (SSF) reinforced modified resole resin (MRR) composites. For this purpose, different SSF loading composites were prepared: 40, 55, and 65 wt.%. The ablation resistance related to mass loss parameters was quantified by testing under an oxyacetyle
J. Aerosp. Technol. Manag.. Publicado em: 21/06/2018
-
33. Superhydrophobic Copper Foam Supported Phase Change Composites with High Thermal Conductivity for Energy Storage
Superhydrophobic and superoleophilic oxidized copper foam (OCF) was prepared by oxidation of copper foam using (NH4)2S2O8 to generate rough surface then followed by modification with low surface energy substance polydimethylsiloxane (PDMS) and stearic acid (SA). Based on sperwetting, form-stable phase change materials (PCMs) composites were obtained by facil
Mat. Res.. Publicado em: 22/03/2018
-
34. Cashew nut shell liquid, a valuable raw material for generating semiconductive polyaniline nanofibers
Abstract Cashew nut shell liquid (CNSL) is an abundant and renewable by-product of the cashew nut industry. It appears to be a valuable raw material for generating semiconductive polyaniline (PAni) nanomaterial with enhanced thermal stability and well-defined nanofiber morphology following a polymerization dispersion process. This study confirms that CNSL a
Polímeros. Publicado em: 15/03/2018
-
35. Modeling of the temperature field generated by the deposition of weld bead on a steel butt joint by FEM techniques and thermographic images.
The aim of this work is to predict the temperature field generated by welding a steel butt joint (API 5L X80). The prediction was modeled by finite element software Abaqus where the subroutine was developed in Fortran so that heat source motion may be included. The motion was based on the Goldak's double ellipsoid. In the model material nonlinearities were i
Mat. Res.. Publicado em: 23/02/2018
-
36. Birefringence, Photo luminous, Optical Limiting and Third Order Nonlinear Optical Properties of Glycinium Phosphite (GlP) Single Crystal: A potential Semi Organic Crystal for Laser and Photonics Applications
Glycinium Phosphite (GlP) has been synthesized and characterized successfully. The fluorescence spectrum of the compound showed one broad peak at 282 nm. Linear absorption value was calculated by Optical Limiting method. Birefringence study was carried out and the birefringence of the crystal is found to be depending on the wavelength in the entire visible r
Mat. Res.. Publicado em: 11/01/2018