Thermal Behaviour
Mostrando 1-12 de 122 artigos, teses e dissertações.
-
1. PHYSICAL, MECHANICAL AND THERMAL BEHAVIOUR OF ADOBE STABILIZED WITH THE SLUDGE OF WASTEWATER TREATMENT PLANTS
ABSTRACT The need for treated water is essential for life. With the constant increase in population, the most common way to purify surface water is through conventional water treatment plants (WTPs). The high volume of residue (sludge) generated in this process is most often returned to the catchment site, negatively affecting the ecosystem. The sludge of WT
Eng. Agríc.. Publicado em: 09/12/2019
-
2. Reduction Behavior of Low Grade Iron Ore at Reducing Conditions Simulating Different Zones of Blast Furnace
Representative technological samples for Baharia iron ore are collected from El-Gedida iron ore mines at the western desert of Egypt. Baharia iron ore was fired at 1000ºC for 3 hours, then the green and fired samples was isothermally reduced by different ratios of H2/CO/CO2/N2 which closely represent the theoretical reduction conditions in different zones o
Mat. Res.. Publicado em: 02/09/2019
-
3. Effect of Processing Parameters on Hot Deformation Behaviour and Microstructural Evolution of PM Ti-5553 Alloy at a Moderate-high Strain Rate
Isothermal compression tests of Ti-5553 (Ti-5Al-5V-5Mo-3Cr) alloy, produced by a fast consolidation approach from blended elemental powder mixture, were performed on a Gleeble® 3800 thermal-physical simulator to investigate its hot deformation behaviour. The samples were compressed in a wide temperature range from 700 ºC to 1150 ºC and a moderate-high str
Mat. Res.. Publicado em: 10/06/2019
-
4. PCL/ZnO Bio-friendly Films as Food Packaging Material.Thermal and morphological analysis
ABSTRACT Films of Poly(?-caprolactone) (PCL) and PCL/Zinc Oxide (ZnO) were obtained by solution processing. Thermal behaviour and morphological structure were analysed by means of Thermogravimetry (TGA), Differential Scanning Calorimetry (DSC), Optical Microscopy (OM) and Scanning Electron Microscopy (SEM). The addition of ZnO to PCL decreased the degradatio
Matéria (Rio J.). Publicado em: 06/12/2018
-
5. Characterization of hibiscus sabdariffa fiber as potential reinforcement for denture acrylic resins
ABSTRACT This study aimed to determine the characteristics of Hibiscus sabdariffa as a fiber-reinforcement material for denture acrylic resins. The Hibiscus sabdariffa fiber was extracted by hot water retting. The fiber was treated at room temperature in aqueous solution of NaOH for 8 hours at 8% concentration. Micrometre gauge and Field emission scanning el
Matéria (Rio J.). Publicado em: 06/12/2018
-
6. Experimental study of brass properties through perforation tests using a thermal chamber for elevated temperatures
Abstract Experimental analysis on standard brass alloy has been carried out using a high pressure gas gun. Perforation tests have been performed for a variety of impact velocities from 40 to 120 m/s in order to study the material behaviour and to define failure modes. The main aim of the study has been to provide results using an innovative thermal chamber t
Lat. Am. j. solids struct.. Publicado em: 22/10/2018
-
7. Biology, distribution and geographic variation of loliginid squids (Mollusca: Cephalopoda) off southwestern Atlantic
ABSTRACT The biology and ecology of southwestern Atlantic loliginid squids have been intensively researched in the last few decades, mostly off the Brazilian southern coast. However, information gathered by scientific research cruisers, either past or recent, is limited. Three species of loliginid squids - the warm-tempered Doryteuthis sanpaulensis (Brakonie
Zoologia (Curitiba). Publicado em: 18/10/2018
-
8. Effect of Heat Input on the Mechanical Behaviour of Al-Cu FSW Lap Joints
Dissimilar Al-Cu joints are desirable due to the combination of the good electrical and thermal properties of copper with the economic advantages of aluminium. However, different chemical, mechanical and thermal properties turn dissimilar welding into a challenge with traditional fusion welding techniques. Friction stir welding appears to be a good alternati
Mat. Res.. Publicado em: 28/05/2018
-
9. Liposomes as potential carriers for ketorolac ophthalmic delivery: formulation and stability issues
ABSTRACT Drug delivery to treat ocular disorders locally is a challenging endeavor. Traditional ocular dosage form - eye drops - exhibits poor availability, consequently inefficient therapeutic response. The objective of the study was to formulate and characterize a ketorolac tromethamine ocular system with a prolonged release pattern based on liposomes as a
Braz. J. Pharm. Sci.. Publicado em: 22/06/2017
-
10. Slow Cook-Off Simulation of PBX Based on RDX
ABSTRACT: Cook-off tests are commonly used to assess thermal behaviour of energetic materials under external thermal stimuli. Numerical simulation became a powerful tool to reduce the costs with experimental tests. However, numerical simulations are not able to predict the violence of thermal response, but instead accurately reproduce radial heat flow in the
J. Aerosp. Technol. Manag.. Publicado em: 2017-06
-
11. Studies on Growth, Spectral, Thermal, Mechanical and Optical Properties of 4-Bromoanilinium 4-Methylbenzenesulfonate Crystal: A Third Order Nonlinear Optical Material
Abstract 4-Bromoanilinium 4-methylbenzenesulfonate (4BPTS) single crystal was successfully grown from ethanol by slow evaporation method at room temperature. The structure of grown crystal was confirmed by single crystal X-ray diffraction studies. The presence of functional groups of grown crystal was confirmed by the Fourier transform infrared spectroscopy
Mat. Res.. Publicado em: 18/07/2016
-
12. Investigations on Preparation and Characterization of Certain Copolyesters
In this paper, we report on the synthesis and characterization of high molecular weight copolyesters from Terephthalic acid, 1, 4 butane diol and Succinic acid /Sebacic acid through a two step process of melt polycondensation using titanium tetra butoxide as catalyst. The synthesized aromatic-aliphatic random copolyesters were characterized by means of FTIR,
Mat. Res.. Publicado em: 26/02/2016