Surface Temperature
Mostrando 1-12 de 2381 artigos, teses e dissertações.
-
1. Study of rhombohedral tricalcium phosphate in hexagonal crystal structure family on the sample prepared by the sol-gel route and the effect of calcination temperature
Abstract The effect of the calcination temperature at 800 and 1000 °C on the stable formation of the tricalcium phosphate with rhombohedral structure in the system of the hexagonal crystal family was determined, while its precursor was made from limestone obtained from nature in the Lumajang district, Indonesia. The rhombohedral tricalcium phosphate samples
Cerâmica. Publicado em: 2023
-
2. Morphology Behavior of Copper Films Deposited after Wet Surface Treatment on Polished Alumina
In this paper, a pre-treatment process for electroless copper (Cu) deposition on the polished alumina (Al2O3) 99.9% and the behavior of Cu plating by electroless process after Al2O3 surface treatment were explored. Our work was carried out by changing the roughness of Al2O3 through micro-etching (coarsening), nucleation its surface by a two-step method (sens
Journal of the Brazilian Chemical Society. Publicado em: 2022
-
3. PLANEJAMENTO FATORIAL NA SÍNTESE DO OLEATO DE ETILA CATALISADA PELA LIPASE NATIVA DE Aspergillus niger
This work reports the use of the Octave, a free computational software, to optimize the experimental design in the synthesis of ethyl oleate from oleic acid and ethanol catalyzed by a native lipase from Aspergillus niger. The central composite factorial design (CCD) was performed with 2 levels and 3 variables (temperature, mass of native A. niger lipase and
Química Nova. Publicado em: 2022
-
4. The Influence of the Platinum Weight Percentage in the Catalyst Formulation on the Performance of a High Temperature Ethanol Electroreformer Based on H3PO4 Doped Polybenzimidazole for Green Hydrogen Production
A vapor-fed high temperature proton exchange ethanol electroreformer has been developed based on the use of a H3PO4-doped polybenzimidazole membrane to produce green hydrogen. As a key parameter, this article describes the influence of platinum weight percent (wt.%) in the catalyst formulation from different commercial catalysts (20, 40, 60, 80 wt.% Pt/C and
Journal of the Brazilian Chemical Society. Publicado em: 2022
-
5. Iron Cobaltite (FeCo2O4) Nanocatalysts for Water-Oxidation: Effects of Annealing Temperature on Catalytic Properties
The development of efficient, stable, and non-precious metal water oxidation catalysts (WOCs) is a matter of importance for sustainable energy research. In this work, iron cobaltite (FeCo2O4) nanoparticles were prepared by the coprecipitation method, and we present the effect of heat treatment (250, 350, 450, 650 and 900 °C) on the catalytic properties. Cat
Journal of the Brazilian Chemical Society. Publicado em: 2022
-
6. Evaluation of the self-healing capacity of ceramics produced with alumina and silicon carbide
Abstract The self-healing capacity of a ceramic material produced by uniaxial pressing with alumina (Al2O3), silicon carbide (SiC), and magnesium oxide (MgO) was evaluated. To assess self-healing, a discontinuity was generated on the surface of the specimens. The healing time in the oven, at a temperature of 1000 ºC, was 1, 30, and 60 min. The specimens wer
Cerâmica. Publicado em: 2022
-
7. Optimization of potato starch gel formulation as green alternative of animal-sourced gelatin
Abstract This study was aimed at optimization of potato starch gel preparation process by response surface methodology and various process parameters were optimized for textural, gelation and sensory properties. 3D response surface and contour plots showed that independent variables, such as extraction time, extraction temperature and potato starch concentra
Food Sci. Technol. Publicado em: 2021-09
-
8. Optimization of ultrasound-assisted extraction of turkish propolis and characterization of phenolic profile, antioxidant and antimicrobial activity
Abstract This study aimed to determine optimum conditions of the ultrasound assited extraction (UAS) parameters for different solvent types by using response surface methodology (RSM) and Box- Behnken design. The model parameters namely, time, temperature and ultrasound power significantly affected TPC value of the propolis extract (P < 0.05). The optimum pr
Food Sci. Technol. Publicado em: 2021-09
-
9. Multivariate Optimization Applied to the Synthesis of Meglumine Antimoniate with Low Levels of Trivalent Antimony
Meglumine antimoniate (MA) is a pentavalent antimony (SbV) drug recommended for the treatment of leishmaniasis. It is known that the trivalent antimony (SbIII) present as a residue in MA contributes to the drug side effects. In this article, multivariate optimization was used in the synthesis of MA in order to obtain a drug with low levels of SbIII. Four var
J. Braz. Chem. Soc.. Publicado em: 2021-08
-
10. Extraction optimization and antioxidant activity of Phyllanthus urinaria polysaccharides
Abstract Three extraction parameters including extraction time, material to solvent ratio, and extraction temperature for the extraction yield of Phyllanthus urinaria polysaccharides were optimized by response surface methodology. The results revealed that the optimal extraction process was extraction time of 5.3 h, extraction temperature of 93 °C, and mate
Food Sci. Technol. Publicado em: 2021-06
-
11. Microbial activity and studies on excavated megalithic micaceous potsherds from Peninsular India
Abstract The abundantly available mica flakes were added in raw materials to manufacture pottery in Central Peninsular India during the early Iron Age (700-300 BCE) for storage and glittering. The micaceous potsherds from the excavated megalithic site of Nagpur were studied for their composition, manufacturing techniques, microstructural features, microbial
Cerâmica. Publicado em: 2021-06
-
12. Optimization and Study of the Response Surface of Properties for the Synthesis of ZSM-5 Zeolites with Hierarchical Pore Structure Obtained by Desilication
Hierarchical ZSM-5 zeolites were prepared by alkali treatment (desilication) at two temperatures, two reaction times, and two NaOH concentrations. A 23 factorial design was used to study the effect of these variables on the crystallinity, microporosity, and mesoporosity of the zeolite due to the desilication treatment. The factorial design analysis showed th
J. Braz. Chem. Soc.. Publicado em: 2021-06