Surface Roughness
Mostrando 25-36 de 549 artigos, teses e dissertações.
-
25. Aplicação da técnica de CAMQL na retificação cilíndrica externa do aço AISI 4340 utilizando rebolo de CBN
RESUMO O processo de retificação possui como características o bom acabamento superficial e alta precisão dimensional e geométrica. Assim, peças usinadas por este processo possuem um alto valor agregado por se tratar de um processo de acabamento que é comumente realizado nas últimas etapas da fabricação. Um fator limitador do processo de retificaç
Matéria (Rio J.). Publicado em: 16/09/2019
-
26. Influence of the incorporation of triclosan methacrylate on the physical properties and antibacterial activity of resin composite
Abstract The incorporation of antimicrobials in the composites as an attempt to reduce bacterial adhesion without jeopardizing mechanical properties is a challenge for Dentistry. Objective: To evaluate the bacterial adhesion and physical properties of a composite containing the methacrylate triclosan- derivative monomer (TM). Methodology: TM was synthesize
J. Appl. Oral Sci.. Publicado em: 09/09/2019
-
27. Assessment of the Fatigue Behavior of Ti-6Al-4V ELI Alloy with Surface Treated by Nd:YAG Laser Irradiation
The effect of a surface treatment by Nd:YAG laser irradiation on the fatigue behavior of Ti-6Al-4V ELI was studied. Axial fatigue tests were performed to obtain S-N curves in polished and laser treated conditions. Roughness measurements and scanning electron microscopy were used to characterize the features of the modified surface. A reduction in the fatigue
Mat. Res.. Publicado em: 05/09/2019
-
28. Superhydrophobic silicon fabricated by phosphomolybdic acid-assisted electrochemical etching
Controllable geometry silicon surfaces with superhydrophobicity are difficult to be fabricated without photolithography techniques. Superhydrophobic silicon surfaces with water contact angle larger than 150º and sliding angle less than 10º have been successfully fabricated by electrochemical etching strategy. Squarelike hole arrays with controllable geomet
Quím. Nova. Publicado em: 26/08/2019
-
29. The effect of a 3% hydroxyapatite paste prophylaxis after different root-scaling procedures in periodontics
Resumo Introdução Procedimentos de raspagem na superfície radicular aumentam a rugosidade superficial durante a instrumentação. O uso de pasta profilática pode reduzir a rugosidade. Objetivo Este estudo avaliou a influência da profilaxia com pasta na rugosidade superficial da dentina radicular após instrumentação manual (IH), ultrassom (US) e ins
Rev. odontol. UNESP. Publicado em: 15/08/2019
-
30. Electrospinning synthesis and assessment of physicochemical properties and biocompatibility of cobalt nitrate fibers for wound healing applications
Abstract: The aim of this study was to develop polyurethane (PU) wound dressing incorporated with cobalt nitrate using electrospinning technique. The morphology analysis revealed that the developed composites exhibited reduced fiber and pore diameter than the pristine PU. The electrospun membranes exhibited average porosity in the range of 67% - 71%. Energy-
An. Acad. Bras. Ciênc.. Publicado em: 29/07/2019
-
31. Influence of Zirconia-Coated Bioactive Glass on Gingival Fibroblast Behavior
Resumo O objetivo deste estudo foi o desenvolvimento de um recobrimento de vidro bioativo sobre a zircônia (Zr) para modular o fenótipo de fibroblastos gengivais. Para este propósito, partículas de Biosilicato® (6 mg/mL) em um veículo a base de água/álcool isopropílico (1:1) foram aplicadas sobre discos de zircônia seguido por tratamento térmico a
Braz. Dent. J.. Publicado em: 22/07/2019
-
32. Influence of the Gas Pressure of Plasma Nitriding on the Structural, Mechanical and Tribological Surface Properties of AISI 316L
In this paper, the influence of gas nitriding (80% H2-20% N2) pressure (between 3 and 7 Torr) on the modification of surface properties of AISI 316L stainless steel is examined. The structural, mechanical, tribological and electrochemical properties of the layer produced in disk samples were studied. The samples’ characteristics were determined by scanning
Mat. Res.. Publicado em: 15/07/2019
-
33. Path coefficient analysis, a different approach to identify soil quality indicators
RESUMO Os indicadores de qualidade do solo relacionados à redução da erosão hídrica podem auxiliar no correto manejo do solo. Com o auxílio da análise de trilha, objetivou-se com a pesquisa identificar algumas variáveis que possam ser utilizadas como indicadores de qualidade do solo relacionados à redução da erosão hídrica. A pesquisa foi realiz
Rev. bras. eng. agríc. ambient.. Publicado em: 10/07/2019
-
34. Influence of a Femtosecond Laser Surface Modification on the Fatigue Behavior of Ti-6Al-4V ELI Alloy
The objective of this investigation was to evaluate the influence of surface modification by femtosecond laser (with average fluence of 0.6 J/cm2 and scanning speed of 0.1 mm/s) on the fatigue resistance of Ti-6Al-4V ELI alloy. A significant reduction in the fatigue strength of the material modified by laser was observed. Residual tensile stresses generated
Mat. Res.. Publicado em: 01/07/2019
-
35. Blood compatibility assessments of electrospun polyurethane nanocomposites blended with megni oil for tissue engineering applications
Abstract: Tissue engineering holds as a prominent technique to repair or replace the damaged human parts to recreate its native function. In this research, a novel scaffold based on polyurethane (PU) comprising megni oil was electrospun for tissue engineering applications. The obtained polyurethane blended with megni oil nanofibers were characterized by scan
An. Acad. Bras. Ciênc.. Publicado em: 19/06/2019
-
36. Análise do Desempenho do Modelo WRF num Episódio de Vento Intenso e Persistente num Grande Reservatório Tropical
Resumo O presente estudo apresenta uma aplicação do modelo de mesoescala WRF à simulação de um episódio de vento intenso e persistente que ocorre com frequência irregular no reservatório de Guapé, MG. Tal evento altera a rotina da população na região, fazendo com que, por exemplo, a embarcação que faz a travessia entre as cidades de Guapé e Ca
Rev. bras. meteorol.. Publicado em: 30/05/2019