Slow Cooling
Mostrando 1-12 de 68 artigos, teses e dissertações.
-
1. Microstructural Adjustments and Tensile Properties of a Hot-Forged Ti−22Al−23Nb−3V−Y Alloy
Microstructures and tensile properties of a hot forged Ti−22Al−23Nb−3V−Y alloy were investigated systematically. Different heat treatments were performed to adjust the wrought microstructure to optimize tensile properties. It was found that features of O phase precipitates and its volume fraction was rather sensitive to the cooling rate after the sol
Mat. Res.. Publicado em: 19/08/2019
-
2. Durability of Concrete After Fire Through Accelerated Carbonation Tests
Degradation of mechanical properties and durability of reinforced concrete structures occur when they are subjected to fire situations, depending on the characteristics of the material, fire duration and the ways of fire extinguishing. Mechanical properties such as compressive strength, tensile strength and elasticity modulus are some examples of typically a
Mat. Res.. Publicado em: 18/07/2019
-
3. Delayed carcass chilling improves tenderness of the beef gluteus medius muscle
Resumo: O objetivo deste trabalho foi avaliar os efeitos de uma taxa de resfriamento mais lenta sobre as características físico-químicas da alcatra (M. gluteus medius) de touros F1 Angus x Nelore, maturada por 14 dias. Carcaças leves e magras (n = 30) foram divididas em meias carcaças e selecionadas para controle (2°C por 24 horas) e tratamento (10°C
Pesq. agropec. bras.. Publicado em: 06/05/2019
-
4. Influence of heat treatments on the microstructure and degree of sensitization of base metal and weld of AISI 430 stainless steel
ABSTRACT AISI 430 is a non-stabilized ferritic stainless steel grade with carbon content lower than 0.12%.After hot and cold rolling this material is annealed. The slow cooling after soaking at temperatures between 900oC and 1000oC promotes the formation of a high quantity of carbides and nitrides, while the rapid cooling partially suppresses the formation o
Matéria (Rio J.). Publicado em: 08/01/2018
-
5. Effect of the Cooling Rate on the Properties of Veneer Porcelain for Zirconia Dental Prosthesis
To solve chipping of veneer porcelain in zirconia dental prosthesis it has been studied different cooling rates in firing schedules to control residual stresses generated by differences in thermal properties between the ceramics. However, cooling rates may affect the porcelain, irrespectively of interaction with zirconia. This study analyzed the effect of co
Mat. Res.. Publicado em: 07/08/2017
-
6. Characterization of basic oxygen furnace slag and granite waste mixtures to Portland cement production
Abstract The aim of this paper is to analyze mixtures of basic oxygen furnace slag and granite waste in order to produce Portland cement. X-ray patterns were carried out in both the basic oxygen furnace slag and granite waste. Then, mixtures were prepared to obtain the binary basicity of 0.5, 0.9 and 1.2. The mixtures were melted at 1500ºC. Two cooling step
REM, Int. Eng. J.. Publicado em: 2016-12
-
7. Strength of 3Y-TZP and feldspathic porcelain subjected to different cooling methods
AIM: To investigate the effect of the cooling rate on flexural strength of monolayer and bilayer porcelain/zirconia (Y-TZP) bars. METHODS: Forty-five specimens were made for each design group: (PM) monolithic specimens of veneer porcelain Vita VM9 (Vita, Germany); (ZM) monolithic specimens of zirconia (ZiHP; ProtMat, Brazil); (PB) bilayer specimens zir
Braz. J. Oral Sci.. Publicado em: 2014-04
-
8. Desenvolvimento de protocolo para criopreservação de folículos ovarianos de peixes usando vitrificação / Development of cryopreservation protocol for fish ovarian follicles using vitrification
Cryopreservation of fish embryos has been under investigation for over two decades; however every protocol tested so far has failed. The use of oocytes has more recently been reported as an alternative, nevertheless most of the studies were carried out using a single technique - controlled slow cooling - and success also remains elusive. Vitrification is an
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 2012
-
9. Influência da diminuição da temperatura sobre o fuso meiótico de oócitos de camundongas e de mulheres maturados in vitro / Low temperature influence on meiotic oocyte spindle of mice and humans after maturation in vitro
Introduction: The meiotic spindle of most mammals is sensitive to cooling and depolymerizes even after a slight reduction in temperature. This is well described and studied on matured oocytes at metaphase II (MII). However, little is known about the influence of low temperatures under meiotic spindle of imature oocytes. In this way, we sougth to evaluate: 1)
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 14/06/2011
-
10. Influência das condições de resfriamento sobre as propriedades superficiais e eletroquímicas de anodos dimensionalmente estáveis
Surface and electrochemical properties of the dimensionally stable anode Ti/(Ru0.3Ti0.7)O2 were studied as a function of the annealing temperature using different conditions in order to perform the cooling process of the oxide films (conventional thermal shock and the slow cooling processes). It was found that surface and electrochemical properties for the o
Química Nova. Publicado em: 2011
-
11. Efecto de los ciclos térmicos sobre la ZAT de una soldadura multipasos de un acero inoxidable superdúplex SAF 2507
Thermal cycles experienced by a superduplex stainless steel SAF 2507 when is welded, can promote the precipitation of secondary phases which decrease the mechanical properties as well as the corrosion resistance. Due to the application of the duplex alloys in the petrochemical industry, the study of these alloys has become very important in order to predict
Soldagem & Inspeção. Publicado em: 2010-09
-
12. Evolução estrutural e térmica de um batólito sin-cinemático no orógenos Neoproterozóico Araçuaí (leste do Brasil) / Structural and thermal evolution of a synkinematic batholith from the Neoproterozoic Araçuaí hot orogen (eastern Brazil)
A faixa Araçuaí, de idade neoproterozóica, caracteriza-se por apresentar em seu domínio alóctone, uma grande quantidade de intrusões magmáticas, uma crosta parcialmente fundida e rochas de facies granulítica, características de uma geoterma elevada, configurando trata-se de um orógeno quente. A suíte tonalítica Galiléia, alojada em metassediment
Publicado em: 2010