Roughness Parameters
Mostrando 13-24 de 161 artigos, teses e dissertações.
-
13. Surface Integrity Analisys in the Hard Turning of Cemented Steel AISI 4317
This work was based on the surface integrity analysis of hardened steel, AISI 4317 case carburized, quenched and tempered with 58 HRC, obtained by a turning operation executed with CBN (cubic boron nitride) tool, varying three basic cutting parameters (cutting speed, feed rate and cutting depth). The surface integrity characterization was conducted analyzing
Mat. Res.. Publicado em: 26/07/2018
-
14. Effect of Flame Spray Deposition Parameters on The Microstructure of Al2 O3 - 13 %TiO2 Coatings Applied Onto 7075 Aluminum Alloy
In this work, the effect of flame spraying parameters on physical, structural and microstructural characteristics of Al2O3 - 13 wt.% TiO2 (AT-13) coatings were studied. NiCrAl and AT-13 feedstock powders were used for spraying a bond coat (BC) and a top coat (TC), respectively, onto a 7075 aluminum alloy substrate. The effect of acetylene-to-oxygen ratio and
Mat. Res.. Publicado em: 10/07/2018
-
15. Using rodogram function to characterize hurst coefficient in rock profiles
Abstract Roughness is a fundamental feature to define rock deformability and resistance. A detailed characterization of discontinuity surface geometry is essential for understanding some of the rock’s mechanical behaviors. Fractal geometry has been used by several authors to correlate parameters such as the Hurst coefficient for JRC (Joint Roughness coeffi
REM, Int. Eng. J.. Publicado em: 2018-07
-
16. The Effect of Controlled Shot Peening on the Microstructure and Fatigue Behavior of Wet Copper-Based Powder Metallurgy Friction Plates
The effects of shot peening treatments on the microstructure and fatigue behavior of the teeth root in wet copper-based powder metallurgy friction plates were investigated and an efficient method for selecting optimal shot peening parameters for friction plates was proposed. Different experimental processes including microscopy observation, microhardness, ro
Mat. Res.. Publicado em: 07/05/2018
-
17. Effect of grinding and aging on subcritical crack growth of a Y-TZP ceramic
Abstract This study aimed to investigate slow crack growth (SCG) behavior of a zirconia ceramic after grinding and simulated aging with low-temperature degradation (LTD). Complementary analysis of hardness, surface topography, crystalline phase transformation, and roughness were also measured. Disc-shaped specimens (15 mm Ø × 1.2 mm thick, n = 42) of a ful
Braz. oral res.. Publicado em: 03/05/2018
-
18. Determination of the effective anticandidal concentration of denture cleanser tablets on some denture base resins
Abstract Objective Although the effectiveness of chemical cleansing against Candida albicans biofilm has been shown, the effective concentration of denture cleanser tablets has not been studied. The aim of this study was to assess the effect of three denture materials against Candida albicans biofilm and to determine effective concentrations of denture clea
J. Appl. Oral Sci.. Publicado em: 18/01/2018
-
19. Mechanical behavior of yttria-stabilized tetragonal zirconia polycrystal: Effects of different aging regimens
Abstract This study aimed to characterize and compare the effect of different aging regimens on surface characteristic (topography and roughness), structural stability (phase transformation) and mechanical performance (Weibull analysis) of a Y-TZP ceramic. Discs (15 × 1.2 mm; VITA In-Ceram YZ) were prepared according to ISO 6872-2015 for biaxial flexural st
Braz. oral res.. Publicado em: 07/12/2017
-
20. Application viability evaluation of the Minimum Quantity Lubrication coolant technique under different flow rates in Plunge Cylindrical Grinding of the ABNT 4340 steel with aluminum oxide wheel
Abstract The coolant delivery technique known as Minimal Quantity Lubrication (MQL) has been employed in machining since the end of the 20th Century and has gained considerable evidence in the last years as a viable alternative to the use of the conventional coolant technique (flood). Due to the low oil flow rate delivered by the MQL technique in grinding op
REM, Int. Eng. J.. Publicado em: 2017-12
-
21. Surface Characterization of NiTi Superelastic and Shape Memory Alloys After Electrolytic Polishing
For the biomedical application of NiTi alloys, an excellent surface finishing process is required to guarantee high corrosion resistance and biocompatibility, eliminating the allergenic and toxic effects associated with the release of nickel ions in the body. Electropolishing is a process that can reduce surface imperfections and form a thin protective layer
Mat. Res.. Publicado em: 09/11/2017
-
22. Effect of solvents on the morphology of PMMA films fabricated by spin-coating
Abstract A method to produce thin layer of PMMA (poly (methyl methacrylate) films by spin coating is reported. PMMA is dissolved in xylene, a mixture of MIBK-xylene and chloroform. Varying the PMMA concentration and spin-coating speeds controls the thickness of the PMMA films. Using chloroform as solvent evidenced thickness around 10 μm. This thickness is s
Polímeros. Publicado em: 21/09/2017
-
23. The correlation between tribological properties of nanostructure TiN coatings and deposition process parameters in PACVD system
ABSTRACT Titanium base coatings are being used extensively for improving wear characteristics at the surface of different parts. Titanium nitride was deposited by Plasma Assisted Chemical Vapor Deposition (PACVD) techniques with purpose improve interface with substrate, as this can increase wearing of the entire part in spite of desirable wear behavior of Ti
Matéria (Rio J.). Publicado em: 22/06/2017
-
24. COMPARATIVE STUDY OF THE INHIBITIVE ACTION BETWEEN THE BITTER ORANGE LEAF EXTRACT AND ITS CHEMICAL CONSTITUENT LINALOOL ON THE MILD STEEL CORROSION IN HCL SOLUTION
Bitter orange, Citrus Aurantium (CA), extract and one of its chemical constituents, Linalool, have been evaluated as a corrosion inhibitor for mild steel in 0.5 mol L-1 hydrochloric acid (HCl) solution using potentiodynamic polarization, electrochemical impedance, Fourier transform infrared spectroscopy (FTIR), and atomic force spectroscopy (AFM) techniques.
Quím. Nova. Publicado em: 2017-05