Residual Strength
Mostrando 1-12 de 153 artigos, teses e dissertações.
-
1. Mechanical properties and fractography of cement-based composites reinforced by natural piassava and jute fibers
Abstract Today’s demand for environmentally friendly and energy-efficient solutions to the construction industry has driven researchers to match natural resources with traditional technics to develop new building technologies. However, there are literature limitations about the correlation of fiber-matrix interface with the failure of natural fibers in mor
Cerâmica. Publicado em: 2022
-
2. Concurrent Validity of the Static and Dynamic Measures of Inspiratory Muscle Strength: Comparison between Maximal Inspiratory Pressure and S-Index
Abstract Objective: To verify the concurrent validity between the inspiratory muscle strength (IMS) values obtained in static (maximal inspiratory pressure [MIP]) and dynamic (S-Index) assessments. Methods: Healthy individuals were submitted to two periods of evaluation: i) MIP, static maneuver to obtain IMS, determined by the Mueller’s maneuver from res
Braz. J. Cardiovasc. Surg.. Publicado em: 2020-08
-
3. Stabilization of sandy soil with high content of asphalt emulsion
Abstract The purpose of this article is to evaluate the shear strength parameters of mixtures of sandy soil with high asphalt emulsion contents for their use in geotechnical structures, such as zoned earth dams, embankments, etc. The methodology adopted consisted of: collecting and characterizing samples of sandy soil to be laboratory tested; compacting the
REM, Int. Eng. J.. Publicado em: 2020-06
-
4. Discrimination of pores and cracks in iron ore pellets using deep learning neural networks
Abstract The discrimination between pores and cracks is an important step in the microstructural analysis of iron ore pellets. While the porosity is fundamental during the reduction process in blast furnaces, cracks are strongly detrimental to the mechanical strength. The usual image processing tools cannot automatically discriminate between these two types
REM, Int. Eng. J.. Publicado em: 2020-06
-
5. Concurrent Validity of the Static and Dynamic Measures of Inspiratory Muscle Strength: Comparison between Maximal Inspiratory Pressure and S-Index
Abstract Objective: To verify the concurrent validity between the inspiratory muscle strength (IMS) values obtained in static (maximal inspiratory pressure [MIP]) and dynamic (S-Index) assessments. Methods: Healthy individuals were submitted to two periods of evaluation: i) MIP, static maneuver to obtain IMS, determined by the Mueller’s maneuver from res
Braz. J. Cardiovasc. Surg.. Publicado em: 13/01/2020
-
6. Impacto nas Propriedades Mecânicas e Tensões Residuais do Material ASTM A572 Grau 50 Soldado por Arco Submerso com Alívio de Tensões Térmico
Resumo O aço ASTM A572 Grau 50 é utilizado na fabricação de conjuntos soldados para aerogeradores, por este motivo, a realização de alívio de tensões é de grande importância para correção dos impactos causados pelos processos de soldagem, bem como, o conhecimento das propriedades finais obtidas com a realização deste processo. O objetivo desse
Soldag. insp.. Publicado em: 02/12/2019
-
7. Mechanical behavior of PVD coatings deposited on ADI
ABSTRACT In this work, the mechanical behavior of the coated ADI system is studied. For this purpose, single layer Ti and bilayer Ti/TiN and TiAl/TiAlN coatings, with different thicknesses, were deposited by the PVD technique of cathodic arc deposition on high strength ADI substrates using industrial and experimental devices. The characterization of the coat
Matéria (Rio J.). Publicado em: 25/11/2019
-
8. Caracterização e aproveitamento dos resíduos de argila e argilito provenientes da extração de gipsita no município de Araripina-Brasil como matérias-primas para cerâmica vermelha
Resumo O objetivo deste trabalho foi a caracterização e o aproveitamento dos resíduos de duas argilas (B e C, coletadas em diferentes camadas do capeamento) e argilito, gerados da extração da gipsita no município de Araripina, para a aplicação em cerâmica vermelha. Foram preparados os corpos de prova cerâmicos utilizando as argilas residuais com a
Cerâmica. Publicado em: 14/11/2019
-
9. Experimental study of concrete mixtures to produce UHPRC using sustainable brazilians materials
Abstract An experimental study is presented to produce Ultra High Performance Reinforced Concrete (UHPRC) with sustainable materials produced in Brazil. A complete factorial arrangement was defined and five controllable factors were selected based on the literature review. Cylindrical specimens were tested at 7, 14 and 28 days of curing, with and without hea
Rev. IBRACON Estrut. Mater.. Publicado em: 23/09/2019
-
10. Influência da composição do gás de proteção nas tensões residuais de juntas de aço DP600 soldadas pelo processo GMAW
RESUMO A indústria automobilística vem investindo em novos processos de fabricação que melhoram a produtividade sem perda da qualidade. Entretanto, a presença de tensões residuais, geradas em todos os processos de fabricação, constitui um dos grandes problemas encontrados na indústria metal mecânica, pois estas podem se somar às tensões de carreg
Matéria (Rio J.). Publicado em: 16/09/2019
-
11. Influence of a Femtosecond Laser Surface Modification on the Fatigue Behavior of Ti-6Al-4V ELI Alloy
The objective of this investigation was to evaluate the influence of surface modification by femtosecond laser (with average fluence of 0.6 J/cm2 and scanning speed of 0.1 mm/s) on the fatigue resistance of Ti-6Al-4V ELI alloy. A significant reduction in the fatigue strength of the material modified by laser was observed. Residual tensile stresses generated
Mat. Res.. Publicado em: 01/07/2019
-
12. Inelastic second-order analysis of steel columns under minor-axis bending
Abstract The inelastic second-order behavior of steel structural columns under minor-axis bending is presented in this article. To study this behavior, a nonlinear frame element formulation is adopted in which the steel's plasticity process is accompanied at the nodal points of each finite element through the refined plastic-hinge method (RPHM). A tangent mo
REM, Int. Eng. J.. Publicado em: 19/06/2019