Reinforcement Tension
Mostrando 1-12 de 34 artigos, teses e dissertações.
-
1. Concrete block structural masonry beam shear design: theoretical and experimental analysis and recommendations to the brazilian standards
Resumo Vigas são submetidas à flexão e cisalhamento, sendo esse último esforço o tema desta pesquisa. O objetivo deste trabalho é analisar especificações para dimensionamento ao esforço cortante de vigas de alvenaria estrutural em blocos de concreto, a partir de extensa avaliação da literatura e de ensaios experimentais aqui relatados. A partir de
Rev. IBRACON Estrut. Mater.. Publicado em: 23/09/2019
-
2. Numerical Investigation of Tension Reinforcement Lap Length of Eurocode 2 Using a Four-Point Beam Loading System
Abstract This report presents a computational research on Eurocode 2 (EC2) tension lap lengths (lo) design in a normally reinforced concrete beam, using ANSYS Workbench simulation software program by simulating a laboratory 4-point beam loading test system under static loading(discrete model approach). A typical 4-point laboratory setup loading system was mo
Lat. Am. j. solids struct.. Publicado em: 27/06/2019
-
3. Study on impact of fiber hybridization in material properties of engineered cementitious composites
ABSTRATO Compósito Cimentício Projetado (ECC) é um tipo de compósitos cimentícios reforçados com fibras de alto desempenho melhorados com bom comportamento de tração, compressão e flexão. O ECC é conhecido por seu comportamento de endurecimento de tensão sob tensão e tem sido cada vez mais aplicado na prática de engenharia. O processo de adicio
Matéria (Rio J.). Publicado em: 10/06/2019
-
4. UNA CONCEPCIÓN INTEGRADORA DE LA MOTIVACIÓN HUMANA
RESUMO As teorias da motivação desenvolvidas no século XX são opostas. Requer-se uma que, sobre a base dos fatos, integre harmonicamente os resultados alcançados. Destacamos a aprendizagem das necessidades, baseado em determinantes orgânicos e adquiridos, mediante o reforço afetivo dos objetos do mundo exterior e das palavras em que se canalizam. Os r
Psicol. Estud.. Publicado em: 10/06/2019
-
5. Numerical study of the behaviour of loop bar splicing in joints of reinforced concrete structures
Resumo Emendas com barras retas ocupam muito espaço devido ao comprimento de traspasse necessário. Dessa forma, em situações em que há uma limitação de espaço para a emenda, uma armação que constitui uma solução interessante é a emenda por meio de laço, que, apesar de ter poucos estudos relacionados, vem sendo bastante difundida na construção
Rev. IBRACON Estrut. Mater.. Publicado em: 2019-02
-
6. Structural Behavior of RC Beams Containing a Pre- Diagonal Tension Crack
Abstract This study focuses the light on the shear behavior of pre-cracked beams, and examines the feasibility of applying fracture mechanics concepts to widen the understanding of shear behavior and mechanisms. The experimental program contains ten beam specimens of high strength concrete (HSC) and steel fiber reinforced concrete (SFRC). Pre-cracks were emb
Lat. Am. j. solids struct.. Publicado em: 16/07/2018
-
7. Static Limit Analysis of Reinforced Soil Structures by a Simple Finite Element and Second-Order Cone Programming
Abstract To discretize reinforced soil structures in plane strain and predict their collapse load, a simple three-node triangular finite element is formulated based on the static theorem of the limit analysis. The element satisfies the equilibrium equations and the mechanical boundary conditions in a weak sense. A modified Mohr-Coulomb yield surface is adopt
Lat. Am. j. solids struct.. Publicado em: 2017
-
8. Explicit expression for effective moment of inertia of RC beams
AbstractDeflection is an important design parameter for structures subjected to service load. This paper provides an explicit expression for effective moment of inertia considering cracking, for uniformly distributed loaded reinforced concrete (RC) beams. The proposed explicit expression can be used for rapid prediction of short-term deflection at service lo
Lat. Am. j. solids struct.. Publicado em: 2015-03
-
9. Calculation procedure, verification and detailing of longitudinal reinforcement in the cross section of prestressed elements / Procedimentos de cálculo, verificação e detalhamento de armaduras longitudinais na seção transversal em elementos protendidos
O presente trabalho apresenta métodos de cálculo, verificação e detalhamento de armaduras longitudinais protendidas nas seções transversais de elementos submetidos à flexão conceituando os sistemas de protensão e seus elementos constituintes, bem como, o desenvolvimento de exemplos práticos, calculados e detalhados de maneira didática, visando um
Publicado em: 2010
-
10. Fracture process characterization of fiber-reinforced dental composites evaluated by optical coherence tomography, SEM and optical microscopy
This study used optical coherence tomography (OCT) compared to scanning electron microscopy (SEM) and optical microscopy (OM) to evaluate qualitatively crack propagation and final fracture in restorative composite materials - Filtek Z250 and Filtek Z350 (3M ESPE) - with fiber reinforcement after cyclic loading. Samples were made using a split mold. Initially
Brazilian Dental Journal. Publicado em: 2010
-
11. Tensile behavior of lignocellulosic fiber reinforced polymer composites: Part II buriti petiole/polyester
The current interest for natural fibers as an environmentally correct composite reinforcement has motivated the investigation of new possibilities. For instance, the fibers extracted from the petiole of the buriti palm tree were recently found to have adequate mechanical properties to reinforce polymer composites. Therefore, the present work evaluates the te
Matéria (Rio de Janeiro). Publicado em: 2010
-
12. COMPÓSITOS À BASE DE RESINA EPÓXI REFORÇADOS COM FIBRA DE COCO / COMPOSITES BASED ON EPOXY RESIN REINFORCED WITH COCONUT FIBER
Polymer composites reinforced with fibers are of great interest in the automotive industry, with emphasis to epoxy resin reinforced with glass fibers However, these fibers exhibit abrasive behavior causing wear of equipment, making it susceptible to the loss of properties due to the breakdown of fibers during processing, high cost of manufacturing. In turn,
Publicado em: 2010