Punching
Mostrando 13-24 de 28 artigos, teses e dissertações.
-
13. Análise crítica dos critérios normativos de dimensionamento à punção em lajes lisas
The Brazilian code NBR 6118/2003 introduces significant changes in the criteria for the punching shear strength of reinforced and prestressed concrete flat slabs. In this scenario, the objective of this work is to evaluate these punching shear design procedures in terms of safety, precision and economy with respect to test results of reinforced and prestress
Publicado em: 2008
-
14. Punção em lajes cogumelo de concreto protendido com cabos não-aderentes na ligação laje-pilar de borda / Punção em lajes cogumelo de concreto protendido com cabos não-aderentes na ligação laje-pilar de borda / Punching shear in prestressed concrete flat slabs with slabedge column connections / Punching shear in prestressed concrete flat slabs with slabedge column connections
São investigados o comportamento estrutural e a resistência última à punção de ligações lajepilar de borda, em edifícios em lajes cogumelo de concreto protendido com cabos nãoaderentes, tendo como principal variável a excentricidade da força cortante, dada pela variação da relação M(momento transferido ao pilar) / V(força cortante). Foram en
Publicado em: 2008
-
15. Gestão dos acidentes de trabalho com instrumentos perfurocortantes: estudo em um hospital público de emergência na cidade de Salvador. / Management of labor accident with punching and cutting instruments: a study in an emergency public hospital in the city of Salvador-Bahia.
Acidente de trabalho é um importante problema de saúde pública no Brasil por representar custos sociais elevados e por apresentar conseqüências desastrosas sobre o processo saúde/doença dos trabalhadores. Dados do Centro de Testagem e Aconselhamento da Bahia apontam que no período de 2004 a 2006, o setor público e a cidade de Salvador apresentaram m
Publicado em: 2008
-
16. Estudo de nós soldados tipo K de treliças planas constituídas por seções tubulares circulares de aço
The trusses of circular hollow sections, should be checked about last limit states of plastification and punching shear of chord wall. The standards AWS D1.1: 2002, ANSI /IACS 360-05 and EN 1993-1-8:2005 have virtually identical procedures for the verification of these limits states, based mainly in the works of Wardenier et al. (1991) and Packer and Henders
Publicado em: 2008
-
17. Experimental nervuradas smooth flagstone analysis of reinforcement concrete with shear armor / Análise experimental de lajes lisas nervuradas de concreto armado com armadura de cisalhamento
Two-way waffle flat slabs are structural elements of reinforced concrete supported directly on columns, under bending moments over the two directions, they improve the speed of the execution and save moulds and concrete and, consequently, labor. This work seeks to contribute for the study of the behavior of this kind of slab, as the shear resistance of the r
Publicado em: 2007
-
18. Análise experimental de lajes lisas unidirecionais de concreto armado com pilares retangulares ao puncionamento / Experimental unidirectional smooth flagstone analysis of armed concrete with rectangular pillars to the puncionamento
Foram analisadas experimentalmente 8 (oito) lajes lisas de concreto armado sem armadura de cisalhamento, variando-se a taxa de armadura de flexão secundária e a maior dimensão dos pilares (cmax). As lajes de dimensões (1.800 x 1.800 x 110) mm, mesma armadura flexão principal, menor dimensão dos pilares (cmin) constante e igual a 85 mm, resistência à
Publicado em: 2007
-
19. Punching and broaching combos - a newstamping tool
The crescent searches for the reduction in time production are a factor that stimulates the improvement of the existent manufacturing techniques (Von Steeg 2002 and Waurzyniak 2002). Nowadays, the new researched processes should make possible the fabrication of pieces in a smaller time with a better use of the material resources and equipments (Klein 2002).
Journal of the Brazilian Society of Mechanical Sciences and Engineering. Publicado em: 2006-03
-
20. Punção em lajes cogumelo : estudo da retangularidade dos pilares
Eight reinforced concrete square flat slabs of reinforced concrete were tested. Slabs were 130mm thick with an 1800 mm side and were submitted to central loading, and the objective was to investigate the influence of column rectangularity coefficient. Column cross section dimensions (cmáx/cmín) varyied between 1 and 4, with a constant perimeter equal to 10
Publicado em: 2006
-
21. Punção em lajes cogumelo de concreto armado: análise experimental e numérica. / Punching in reinforced concrete flat slabs: experimental and numerical analysis.
Este trabalho descreve uma pesquisa experimental de lajes cogumelo de concreto armado com armadura de cisalhamento, sem envolver a armadura de flexão. Onze lajes cogumelo quadradas de concreto com 200 mm de espessura e 3000 mm de lado, com uma área central carregada de 200 mm de lado, foram testadas até a ruptura. O principal objetivo dos ensaios foi inve
Publicado em: 2006
-
22. Punção em lajes cogumelo : estudo da retangularidade dos pilares
São analisadas experimentalmente 8 (oito) lajes cogumelo de concreto armado quadradas com 1800 mm de lado e 130 mm de espessura, submetidas a carregamento central, com o objetivo de investigar a influência do índice de retanguralidade do pilar, sendo que a relação entre as dimensões da seção transversal do pilar (cmáx/cmín) variou entre 1 e 4, com
Publicado em: 2006
-
23. SISTEMA DE REGULAGEM DO ESFORÃO DE CORTE EM CHAPAS METÃLICAS COM VARIAÃÃO DE ESPESSURAS / SYSTEM OF REGULATION OF THE CUT EFFORT IN METALLIC PLATES WITH VARIATION IN THICKNESSES
This work presents the project of a system that can be applied under a punching operation with different thickness metal plates and the pressure variation, knowing that is one of the most used process in the mechanical industry conformation, it reaches the most efficient results applied to the studied process. The main is to consider a electropneumatic syste
Publicado em: 2005
-
24. Cálculo de lajes lisas com protensão parcial e limitada.
Flat slabs are associated with rationalization, better esthetic conditions and higher speed during construction. The use of post-tension can make this system viable since it strongly improves the structural performance in respect to punching and in case of extreme deflection of the slab. The durability of prestressed concrete elements is assured by meeting t
Publicado em: 2005