Polypropylene Composites
Mostrando 1-12 de 64 artigos, teses e dissertações.
-
1. Grafting polypropylene over hollow glass microspheres by reactive extrusion
Abstract Hollow glass microspheres HGM are light, round, hollow, hydrophilic microspheres used to produce polyolefin composites with reduced density. To maintain mechanical strength, it is necessary to improve the adhesion between the polymer matrix and the microspheres, which is done by a compatibilizer. For polypropylene composites a maleic anhydride graft
Polímeros. Publicado em: 10/10/2019
-
2. Influence of coupling agents on the adhesion force of dissimilar overmolded polymers: a digital image correlation analysis
ABSTRACT The increase in the technical and functional requirements of plastic items has led the development of multimaterials. To achieve a good performance in the adhesion of dissimilar materials, in this case, polypropylene and coconut fiber composites, it is fundamental to understand the phenomena related to the specific interface. This work aims to evalu
Matéria (Rio J.). Publicado em: 16/09/2019
-
3. THE MULTIROLE OF MODIFIED NATURAL GUMS FOR MULTICOMPONENT POLYMERS: AS COUPLING AGENTS FOR POLYMERS REINFORCED WITH CELLULOSIC FIBERS OR COMPATIBILIZERS FOR BIODEGRADABLE POLYMER BLENDS
In this work, the capability to use pine rosin as a biodegradable coupling agent/compatibilizer is studied. To formulate composites, post-consumer polypropylene and discarded agave fibers (as reinforcing agent) are coupled with pine rosin (in pure or maleated form). Besides, poly(lactic acid) (PLA) with poly(butylene adipate-co-terephthalate) (PBAT) are comp
Quím. Nova. Publicado em: 02/05/2019
-
4. Application of ashes as filling in reprocessed polypropylene: thermomechanical properties of composites
Abstract The life cycle of a product depends to a great extent on its reuse and ease of recycling. This work had developed of composite materials of reprocessed polypropylene composites with rice husk ash (RHA) and sugarcane bagasse ash (SBA) through the coextrusion and injection processes as main purpose. The polymeric matrix was reprocesed until six gener
Polímeros. Publicado em: 28/03/2019
-
5. Improvement of Polypropylene Adhesion by Kraft Lignin Incorporation
Low surface energy and poor adhesion are well-known characteristics of polypropylene (PP). Surface treatments such as plasma, corona, and laser are usually applied to overcome these limitations. However, current studies highlight the incorporation of hydrophilic or amphiphilic polymers into hydrophobic low-surface-energy polymers as an alternative for increa
Mat. Res.. Publicado em: 25/02/2019
-
6. Efeito da adição de fibras híbridas na durabilidade de compósitos cimentícios avançados em ambientes úmidos e agressivos
ABSTRACT Reactive powder concrete (RPC) is one type of advanced cementitious composite that has been increasingly used. Its high mechanical strength enables the application of the composite in bolder structures. Considering its recent history of use, there is a lack of knowledge about this materials durability. Therefore, this paper aimed to evaluate the beh
Matéria (Rio J.). Publicado em: 18/10/2018
-
7. Effect of compatibiliser on the properties of polypropylene/glass fibre/nanoclay composites
Abstract Glass fibre (GF), nanoclay (NC) and hybrid composites compatibilised with maleic anhydride polypropylene (MAPP) were prepared by extrusion and injection moulding. The fourier transform infra-red spectra revealed the characteristic absorption peaks of MAPP in the compatibilised GF and NC composites. A decrement in the peak intensity of X-ray diffrac
Polímeros. Publicado em: 21/05/2018
-
8. Behavior of fiber reinforced mortar composites under impact load
Abstract This paper presents results of the experimental study on the behavior of plain and fiber reinforced cement mortars with different fibers under static and impact compressive load. Glass, polypropylene and carbon fibers were used in equal dosage by mass. The impact test was conducted using an impact tower with drop hammer, which represented the modif
Lat. Am. j. solids struct.. Publicado em: 26/04/2018
-
9. An Evaluation of the Dielectric Barrier Discharge Treatment on the Mechanical, Structural and Morphological Properties of Carbon Fibers
ABSTRACT: Carbon fibers (CFs) have been widely applied in the manufacture of polymeric composites. The mechanical properties of these composites depend on the adhesion in the matrix/CF interface. Since the CFs have poor adhesion properties, a surface treatment of the CFs becomes necessary. The plasma process used in this work was the dielectric barrier disch
J. Aerosp. Technol. Manag.. Publicado em: 29/03/2018
-
10. Layer-by-Layer technique employed to construct multitask interfaces in polymer composites
Abstract The properties of glass fiber-reinforced polymer composites are closely related to the fiber-matrix interface. Interfacial treatments to improve mechanical properties are usually limited to enhance interfacial adhesion. In this work, Layer-by-Layer (LbL) technique was introduced to build a novel interface in polymer composites. Different numbers of
Polímeros. Publicado em: 2017-12
-
11. Polypropylene Composites Manufactured from Recycled Carbon Fibers from Aeronautic Materials Waste
Carbon fiber composites are used in several industries such as, aerospace, automotive, civil engineering, sports goods and technical applications due to its low-weight, strength and stiffness. However, the technology of recycling of these thermosetting polymer composites remains an engineering challenge because of their cross-linked structures that impede th
Mat. Res.. Publicado em: 23/10/2017
-
12. Manufacturing and Characterization of Jute/PP Thermoplastic Commingled Composite
The commingled technology is a promising technique for the manufacture of composites reinforced with natural fibers. This study presents the development, processing and basic characterization of a long fiber Jute/Polypropylene (Jute/PP) commingled composite. The Jute/PP fabric was produced in a handloom and the composite was consolidated by compression moldi
Mat. Res.. Publicado em: 19/10/2017