Polymer Surface
Mostrando 13-24 de 444 artigos, teses e dissertações.
-
13. Modification of Chitosan by Zincke Reaction: Synthesis of a Novel Polycationic Chitosan-Pyridinium Derivative
Chitosan is a biodegradable aminopolysaccharide produced by deacetylation of acetamide groups of chitin, one of the most abundant organic materials in nature. Many different types of organic reactions have been described to modify the functional groups of chitosan and produce materials with applications in a large number of areas. However, the Zincke reactio
J. Braz. Chem. Soc.. Publicado em: 24/10/2019
-
14. Grafting polypropylene over hollow glass microspheres by reactive extrusion
Abstract Hollow glass microspheres HGM are light, round, hollow, hydrophilic microspheres used to produce polyolefin composites with reduced density. To maintain mechanical strength, it is necessary to improve the adhesion between the polymer matrix and the microspheres, which is done by a compatibilizer. For polypropylene composites a maleic anhydride graft
Polímeros. Publicado em: 10/10/2019
-
15. Construction and Evaluation of a Graphene Oxide Functionalized Aminopropyltriethoxy Silane Surface Molecularly Imprinted Polymer Potentiometric Sensor for Dipyridamole Detection in Urine and Pharmaceutical Samples
A dipyridamole (DIP) based surface molecularly imprinted polymer (MIP) was synthesized and applied as a sensing agent in a sensing layer of a new modified potentiometric carbon paste electrode (CPE). The potentiometric modified CPEs (GO@SiO2-NH2-MIP/MWCNTs/CPE, where GO is graphene oxide and MWCNTs is multi-walled carbon nanotubes) showed an improved perform
J. Braz. Chem. Soc.. Publicado em: 16/09/2019
-
16. Influence of coupling agents on the adhesion force of dissimilar overmolded polymers: a digital image correlation analysis
ABSTRACT The increase in the technical and functional requirements of plastic items has led the development of multimaterials. To achieve a good performance in the adhesion of dissimilar materials, in this case, polypropylene and coconut fiber composites, it is fundamental to understand the phenomena related to the specific interface. This work aims to evalu
Matéria (Rio J.). Publicado em: 16/09/2019
-
17. Effect of stem cells combined with a polymer/ceramic membrane on osteoporotic bone repair
Abstract Cell therapy associated with guided bone regeneration (GBR) can be used to treat bone defects under challenging conditions such as osteoporosis. This study aimed to evaluate the effect of mesenchymal stem cells (MSCs) in combination with a poly(vinylidene-trifluoroethylene)/barium titanate (PVDF-TrFE/BT) membrane on bone repair in osteoporotic rats.
Braz. oral res.. Publicado em: 09/09/2019
-
18. Influence of the incorporation of triclosan methacrylate on the physical properties and antibacterial activity of resin composite
Abstract The incorporation of antimicrobials in the composites as an attempt to reduce bacterial adhesion without jeopardizing mechanical properties is a challenge for Dentistry. Objective: To evaluate the bacterial adhesion and physical properties of a composite containing the methacrylate triclosan- derivative monomer (TM). Methodology: TM was synthesize
J. Appl. Oral Sci.. Publicado em: 09/09/2019
-
19. An Anchorage System for Enhanced Bond Behavior between Carbon Fiber Reinforced Polymer Sheets and Cracked Concrete
Abstract The contribution of CFRP wraps, as an anchorage system, to enhancing bond behavior between CFRP sheet and cracked concrete, was investigated. Thirty six concrete blocks (150 x 150 x 200 mm) were cast with 3ϕ12 mm steel bars embedded laterally at different spacing along the 200-mm-dimension. Half of the moist-cured blocks were subjected to a cyclic
Lat. Am. j. solids struct.. Publicado em: 05/09/2019
-
20. Investigation of the Wettability Using Contact Angle Measurements of Green Polyethylene Flat Films and Expanded Vermiculite Clay Treated by Plasma
Polyethylene (PE) is a polymer that has a low adhesion property, which is related to its low surface energy. However, the plasma treatment aims the modification of the surface properties without affecting the polymer structure. In this sense, the objective of this work was to prepare biocomposite films via flat extrusion with Green PE matrix and Expanded Ver
Mat. Res.. Publicado em: 22/08/2019
-
21. Study on influence of polymer and surfactant on in vitro performance of biodegradable aqueous-core nanocapsules of tenofovirdisoproxil fumarate by response surface methodology
The major objective of this study was to investigate the effect of biodegradable polymer type and surfactant concentration on various characteristics viz. particle size, entrapment efficiency and drug release rate constant of aqueous core nanocapsules (ACNs) containing tenofovirdisoproxil fumarate. In this study, the nanocapsules were prepared by modified mu
Braz. J. Pharm. Sci.. Publicado em: 12/08/2019
-
22. Influence of temperature on the adhesion of fibre reinforced polymers to timber surface
Resumo Os reforços de compósitos poliméricos com fibras de carbono (CFRP) e de vidro (GFRP) têm sido largamente usados em estruturas de madeira, onde eles podem estar expostos a condições adversas de temperatura. Para serem usados adequadamente, são necessárias informações sobre a sua adesão ao substrato. O objetivo desta pesquisa é avaliar a inf
Ambient. constr.. Publicado em: 10/06/2019
-
23. Mechanical and bioactivity assessment of wollastonite/PVA composite synthesized from bentonite clay
Resumo Os compósitos de vidro/polímero podem imitar a estrutura natural do osso possuindo uma configuração fibra-matriz que proporciona propriedades físicas e biológicas apropriadas. As cerâmicas de wollastonita são conhecidas por suas bioatividade e biocompatibilidade promissoras quando aplicadas na regeneração óssea. O álcool polivinílico (PVA
Cerâmica. Publicado em: 06/06/2019
-
24. Avaliação do efeito do tratamento corona na performance de estabilizadores de UV em filmes de PEBD
RESUMO A indústria de polímeros tem passado por muitos avanços na última década, dentre eles, podem-se citar as inovações em processamento e no uso de aditivos, o que permite que eles sejam utilizados em diversas aplicações, especialmente quando expostos ao ambiente externo. Porém, para algumas aplicações específicas, o polímero precisa ser sub
Matéria (Rio J.). Publicado em: 20/05/2019