Nitride
Mostrando 13-24 de 162 artigos, teses e dissertações.
-
13. Surface Integrity Analisys in the Hard Turning of Cemented Steel AISI 4317
This work was based on the surface integrity analysis of hardened steel, AISI 4317 case carburized, quenched and tempered with 58 HRC, obtained by a turning operation executed with CBN (cubic boron nitride) tool, varying three basic cutting parameters (cutting speed, feed rate and cutting depth). The surface integrity characterization was conducted analyzing
Mat. Res.. Publicado em: 26/07/2018
-
14. Fatiga de contacto por rodadura en acero SAE 1050 recubierto con TiN, posteriormente templado
ABSTRACT The use of ceramic coatings of the nitride, carbide, or diamond type on steel substrates promotes the improvement of tribology properties. Nevertheless, high hardness gradients and adhesion problems may deteriorate the performance of these coatings when subjected to Rolling Contact Fatigue (RCF). Some studies on steels with ceramic coatings were car
Matéria (Rio J.). Publicado em: 19/07/2018
-
15. Evaluation of the oil flow using the MQL technique applied in the cylindrical plunge grinding of AISI 4340 steel with cbn grinding wheel
Abstract The grinding process is defined as an abrasive cutting action of a tool known as grinding wheel, which is submitted to high rotations, promoting excellent finishing and accuracy in dimensions, respecting the parameters established in each project. During the machining, the cutting edges of the abrasive grains undergo wearing and this increases the c
REM, Int. Eng. J.. Publicado em: 2018-07
-
16. Mechanical Loss Angle Measurement for Stressed thin Film Using Cantilever Ring-Down Method
Mechanical loss of the coating materials, and hence thermal noise from the mirror coatings, is a limiting factor for the sensitivity of the laser interferometer gravitational waves detector at its most sensitive frequency range. Mechanical loss of the thin films are often measured using the cantilever ring-down method. But when the thin film is under stress,
Mat. Res.. Publicado em: 28/05/2018
-
17. Investigation on Friction and Wear Properties of High-Temperature Bearing Steel 9Cr18Mo
This paper presented a study of friction and wear on 9Cr18Mo when rubbed against other materials (steel-304, steel-440C, steel-GCr15 or silicon nitride ceramic ball) at high temperature conditions. Friction and wear tests were carried out with universal a friction and wear testing machine. The wear morphology was analyzed by a Nanovea three-dimensional profi
Mat. Res.. Publicado em: 05/04/2018
-
18. Synthesis of Gallium Nitride and Related Oxides Via Ammonobasic Reactive Sublimation (ARS)
Ammonobasic reactive sublimation (ARS) is proposed as a novel method to synthesize GaN and related oxides. Results indicate that GaN growth occurs by a nitriding process of Ga and related oxides, establishing a direct dependence on NH4OH amount added as a primary chemical reactive. The samples were grown on p-type Si (111) substrates inside a tube furnace, e
Mat. Res.. Publicado em: 28/09/2017
-
19. AVALIAÇÃO DE DIFERENTES ROTAS DE ESFOLIAÇÃO LÍQUIDA PARA OBTENÇÃO DE NANOLAMELAS DE NITRETO DE BORO HEXAGONAL
Hexagonal boron nitride (h-BN), graphite analogous structure, has many interesting applications due to its excellent thermal, electrical and mechanical properties. In this study, different routes of liquid exfoliation using solvent and ultrasound were used to obtain two-dimensional (2D) nanosheets of h-BN. The efficiency of the exfoliative routes was evaluat
Quím. Nova. Publicado em: 2017-09
-
20. Análisis de falla de los bujes del tornillo de una extrusora utilizada para procesar pintura en polvo
ABSTRACT This article aims to present the failure analysis of extruder screw bushings used for the manufacture of powder paint. Two bushings, one from the transition zone and one from the metering zone were selected to carry out the study. Chemical composition and microstructural analysis, hardness testing and a detailed analysis of the failed surfaces by vi
Matéria (Rio J.). Publicado em: 22/06/2017
-
21. The correlation between tribological properties of nanostructure TiN coatings and deposition process parameters in PACVD system
ABSTRACT Titanium base coatings are being used extensively for improving wear characteristics at the surface of different parts. Titanium nitride was deposited by Plasma Assisted Chemical Vapor Deposition (PACVD) techniques with purpose improve interface with substrate, as this can increase wearing of the entire part in spite of desirable wear behavior of Ti
Matéria (Rio J.). Publicado em: 22/06/2017
-
22. Incorporation of N in the TiO2 Lattice Versus Oxidation of TiN: Influence of the Deposition Method on the Energy Gap of N-Doped TiO2 Deposited by Reactive Magnetron Sputtering
N-doped TiO2 can be deposited by reactive magnetron sputtering by two methods: incorporation of nitrogen particles in the TiO2 lattice or incorporation of oxygen particles in the TiN lattice (oxidation). This paper investigates both procedures by experimental and numerical methods in order to establish the best way for incorporation of substitutional nitroge
Mat. Res.. Publicado em: 02/03/2017
-
23. Finite Element Modeling and Experimental Verification of Nitriding Process in S30C Steel
A mathematical model has been developed to simulate the nitriding process of plain carbon steel, considering the simultaneous diffusion of nitrogen in different iron-nitrogen (Fe-N) phases and the precipitation dynamics of γ' and ε iron-nitride. The model can predict the distribution of nitrogen concentration, volume fraction of Fe-N phases and hardness. F
Mat. Res.. Publicado em: 16/02/2017
-
24. Corrosion Behavior Analysis of Plasma-assited PVD Coated Ti-6Al-4V alloy in 2 M NaOH Solution
The work aims the study of the corrosion behavior of nitride plasma-assisted PVD coated Ti-6Al-4V alloy in 2 M NaOH at 25 and 60°C, using open-circuit potential (OCP) versus time measurements, potentiodynamic polarization and electrochemical impedance spectroscopy (EIS). The uncoated Ti-6Al-4V alloy showed a passive behavior. The TiN and TiAlN/TiAlCrN coate
Mat. Res.. Publicado em: 06/02/2017