Necking
Mostrando 1-12 de 15 artigos, teses e dissertações.
-
1. Numerical and experimental investigation of forming limit diagrams of 6063 aluminum alloy sheets using Ayada ductile fracture criterion and the second derivative of large strain criterion at increased temperatures
Abstract The present study investigated the forming limit diagrams (FLDs) of aluminum alloy 6063 sheets using numerical and experimental methods at increased temperatures. In the numerical section, for the first time, the Ayada ductile fracture criterion and the second derivative of the large strain criterion were used. ABAQUS finite element (FE) analysis so
Lat. Am. j. solids struct.. Publicado em: 17/09/2018
-
2. Métodos temporales para determinar deformaciones límite en chapas metálicas
ABSTRACT The forming limit diagram (FLD) –broadly used to characterize sheet-metal formability– is made by means of strain measurement over the surface of stretched samples and the subsequent determination of limit-strain values associated with the onset of necking. Currently, researchers can make strain measurements with digital image-correlation analys
Matéria (Rio J.). Publicado em: 19/07/2018
-
3. Efecto del cambio en el camino de deformación en la formabilidad de chapas de acero DP-780 y zinc Zn20
ABSTRACT The Forming Limit Diagram (FLD), frequently used to characterize the formability of sheet metals, is determined by assuming proportional loading histories up to the onset of necking. However, the limit strains are highly affected by strain-paths changes, which are very usual in real metal forming processes. The aim of this work is to analyze the eff
Matéria (Rio J.). Publicado em: 19/07/2018
-
4. Determination of Forming Limit Diagrams Based on Ductile Damage Models and Necking Criteria
Abstract In this paper, forming limit diagrams (FLDs) for an aluminum alloy are predicted through numerical simulations using various localized necking criteria. A comparative study is conducted for the FLDs determined by using the Lemaitre damage approach and those obtained with the modified Gurson-Tvergaard-Needleman (GTN) damage model. To this end, both d
Lat. Am. j. solids struct.. Publicado em: 2017-10
-
5. Experimental and Numerical Investigation of the Dynamic Behavior of Clamped Thin Panel Subjected to Underwater Impulsive Loading
Abstract The dynamic response and failure mechanism of clamped thin aluminum alloy plates subjected to underwater impulsive loading are investigated by laboratory experiments and finite element (FE) simulations. The effects of plate thickness, impulsive loading and fluid-structure interaction on failure modes in clamped thin aluminum plates are comprehensive
Lat. Am. j. solids struct.. Publicado em: 2017-06
-
6. Photodegradation of UHMWPE Filled with Iron Ore Fine
Ultra high molecular weight polyethylene (UHMWPE) is one of the most important engineering materials owing to outstanding properties like impact strength and abrasion resistance. However, the relatively low Young´s modulus restricts some application and the use of fillers may be a suitable way to overcome this. The fillers can influence the photo stabilizat
Mat. Res.. Publicado em: 23/01/2017
-
7. Influence of the Yield Surface Curvature on the Forming Limit Diagrams Predicted by Crystal Plasticity Theory
Abstract The aim of this paper is to investigate the impact of the microscopic yield surface (i.e., at the single crystal scale) on the forming limit diagrams (FLDs) of face centred cubic (FCC) materials. To predict these FLDs, the bifurcation approach is used within the framework of rate-independent crystal plasticity theory. For this purpose, two micromech
Lat. Am. j. solids struct.. Publicado em: 2016-12
-
8. Effect of Necking Behavior and of Gap Size on the Cooling Rate in Hot Stamping
In this study, a tailored die quenching experimental method using low closing pressures and an aluminum flat die was developed in order to evaluate the effects of the gap size on the cooling rate in the hot stamping process of a 22MnB5 steel grade. Initially, the necking behavior in hot stamping was investigated by deforming the specimens to different strain
Mat. Res.. Publicado em: 29/08/2016
-
9. Estudo da influência dos parâmetros no processo de soldagem GMAW - arco pulsado
Pulsed gas metal arc welding describes the metal transfer mode involving oscillation (pulsing) of the welding current from a high pulse current in which level drop growth, necking of wire tip and detachment occur, and a low background current, which is applied to maintain the arc. The advantages of the process are: metal transfer without spatter formation an
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 29/09/2011
-
10. High-speed camera analysis of rupture of polypropylene specimens in tensile tests / Análise das imagens de ruptura de corpos de prova de polipropileno em ensaio de tração obtidas através de câmera de alta velocidade
Injection-molded isotactic polypropylene, iPP, samples present different properties variation as a function of the injection parameters. One of these properties is the rupture propagation on the material, which was studied with the use a high-speed camera adjusted to capture from 18,000 to 45,000 frames per second. The injection molding parameters modified w
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 29/07/2011
-
11. Influence of the lubricant use in the process of deep drawing with thick steel sheeet metals / Influencia do uso de lubrificantes no processo de estampagem profunda com chapas espessas de aço
The objective of this work was to evaluate the influence of the lubrication on the process and product during the deep drawing of metallic cups, as Brazilian standard ABNT NBR 5906:1984, degree EPA to thickness 3,5mm and to understand the causes of the cracking during deep drawing, on specific conditions of this process. Occurrences of defects as crack, unde
Publicado em: 2007
-
12. Construção e testes de máquina de ensaio de torção plástica para levantamento do comportamento plástico de metais
A computerized prototype machine for cold torsion testing has been developed, constructed and tested in the Laboratory of Metal Forming at UDESC (University the State the Santa Catarina) - Joinville. The equipment consists of a horizontal torsion machine, employing an electric motor, a wheel, a horizontal axle and a control and acquisition data system. The g
Publicado em: 2004