Microstructure Of Titanium
Mostrando 1-12 de 59 artigos, teses e dissertações.
-
1. Effect of titanium and nitrogen inoculation on the microstructure, mechanical properties and abrasive wear resistance of Hadfield Steels
Abstract The effect of titanium and nitrogen addition on Hadfield steels was investigated. In order to do this, two grades of steels were produced in terms of titanium and nitrogen addition. The final samples had their microstructure characterized and their mechanical properties were evaluated by uniaxial tensile and Charpy impact tests. Furthermore, the wea
REM, Int. Eng. J.. Publicado em: 2020-03
-
2. Effect of Scanning Speed on the Surface Roughness of Laser Metal Deposited Copper on Titanium Alloy
This paper reports on the effect of scanning speed on the laser deposited Cu on titanium alloy substrate. The experiments were conducted by varying the scanning speed from 0.3 m/min to 1.2 m/min while the laser power, the powder feed rate and the gas flow rate were kept constant. The laser deposited Cu were characterized through the evolving microstructure a
Mat. Res.. Publicado em: 20/12/2019
-
3. Oxidation Behavior of Al-Y Coating on γ-TiAl at 900°C
ABSTRACT In this study, an Al-Y coating was applied to enhance the property of oxidation resistance on the surface of γ-TiAl alloys by rf magnetron sputtering. The isothermal oxidation tests were investigated at 900 °C for 100 h. The coating characteristics and microstructure of coating after isothermal oxidation were inspected by XRD and SEM methods respe
Matéria (Rio J.). Publicado em: 20/05/2019
-
4. Efeito da mesogeometria da broca e das condições de lubrirrefrigeração sobre o acabamento do furo em aço ARBL DIN S700MC
RESUMO O trabalho apresenta um estudo sobre os efeitos decorrentes da modificação da mesogeometria de uma broca helicoidal de metal-duro com revestimento de TiAlN sobre o acabamento superficial do aço de alta resistência e baixa liga DIN S700MC utilizando diferentes condições de aplicação de fluidos lubrirrefrigerantes (em abundância, em mínima qua
Matéria (Rio J.). Publicado em: 20/05/2019
-
5. Effect of Thermo-Mechanical Treatments on the Microstructure and Mechanical Properties of the Metastable β-type Ti-35Nb-7Zr-5Ta Alloy
In this work, theoretical composition design and thermo-mechanical treatments were combined in order to improve the mechanical compatibility of a biomedical β-type titanium alloy. By applying a composition design theory, cold rolling and low temperature aging, a metastable β-type Ti-35Nb-7Zr-5Ta (wt%) alloy with an elastic modulus of 47 GPa and a yield str
Mat. Res.. Publicado em: 29/10/2018
-
6. Effect of Hot Deformation on Microstructure, Hardness and Precipitation Kinetics in a C350 Maraging Steel Modified by Titanium Addition
Maraging steels are alloys with a good balance between strength and fracture toughness. These properties are obtained by quenching and aging treatments, where the precipitation of intermetallic compounds is promoted in a martensitic matrix. In this context, this paper aims to evaluate the effect of hot deformation on microstructure, kinetics and formation of
Mat. Res.. Publicado em: 17/09/2018
-
7. Estructuras de titanio con gradiente de porosidad – fabricación por el método de partículas espaciadoras y caracterización
ABSTRACT It has proposed the use of porous titanium to reduce the problem of mechanical incompatibility, which occurs between such material used in implants and bone. The pores introduction in titanium decreases its elastic modulus by bringing it closer to that of both cortical and trabecular bones. This paper describes titanium fabrication by powder metallu
Matéria (Rio J.). Publicado em: 19/07/2018
-
8. Estudio de la formabilidad en caliente de aleaciones de titanio a través del ensayo de torsión y su aplicación a la optimización de procesos de forja y extrusión
ABSTRACT In the development of hot metal forming, the metallic products must comply with the requirements imposed by current standards. In some cases, the required microstructure can only be obtained through thermomechanical processing. With titanium and its alloys, small ranges of good workability are an additional difficulty. In this work the hot-workabili
Matéria (Rio J.). Publicado em: 19/07/2018
-
9. Effect of heat cycling on melting and crystallization of PHB/TiO2 compounds
Abstract Compounds of poly(3-hydroxybutyrate) (PHB) and titanium dioxide (TiO2) with filler content between 1% and 10% were prepared in a laboratory internal mixer. The effect of heating and cooling rates on the crystallization and melting of PHB/TiO2 compounds was investigated by differential scanning calorimetry (DSC). Melt and cold crystallization rates
Polímeros. Publicado em: 21/05/2018
-
10. A Novel Porous Diamond - Titanium Biomaterial: Structure, Microstructure, Physico-Mechanical Properties and Biocompatibility
ABSTRACT With the aim of introducing permanent prostheses with main properties equivalent to cortical human bone, Ti-diamond composites were processed through powder metallurgy. Grade 1 titanium and mixtures of Ti powder with 2%, 5% and 10 wt% diamond were compacted at 100MPa, and then sintered at 1250°C/2hr/10-6mbar. Sintered samples were studied in the po
An. Acad. Bras. Ciênc.. Publicado em: 11/12/2017
-
11. Influence of Si Coating on Interfacial Microstructure of Laser Joining of Titanium and Aluminium Alloys
A common phenomenon in the dissimilar joints is the presence of brittle compounds in the joining interface region. The brittle phases can decrease by introduction of interlayers in the joining interface, such as silicon, that inhibits the formation of Al3Ti and AlTi3 phases in joining process between titanium and aluminium alloys. In the present work, the jo
Mat. Res.. Publicado em: 09/11/2017
-
12. Surface Modification of Ti6Al4V Alloy by Pulsed Lasers: Microstructure and Hydrophobic Behavior
In many aerospace applications, it is important to produce hydro-repellent surfaces because water and ice accumulation could lead to malfunctioning of the part or component with a potential critical failure. In this study, it was investigated the texturing of a titanium alloy (Ti6Al4V) by applying a pulsed Nd:YAG laser, aimed at the surface characterization
Mat. Res.. Publicado em: 21/09/2017