Micro Hardness
Mostrando 1-12 de 95 artigos, teses e dissertações.
-
1. Effect of TiC Particles Concentration on Microstructure and Properties of Ni-TiC Composite Coatings
A kind of novel anti-wear Ni-TiC composite coatings was deposited successfully on 42CrMo steel by pulsed electrodeposition method with various TiC particles concentration. The effect of TiC concentration on morphologies and properties of Ni-TiC composite coatings were investigated and the optimum concentration of TiC particle was obtained. Results demonstrat
Mat. Res.. Publicado em: 20/01/2020
-
2. Caracterização Mecânica da Região Soldada de Tailor Welded Blanks (TWB) a Partir do Perfil de Microdureza
Resumo No Tailor Welded Blank (TWB) são soldadas chapas de especificações distintas, antes da conformação. Sua caracterização, na região soldada, por métodos convencionais de tração, pode ser dificultada pelo estreito comprimento da solda. Novas metodologias e alternativas são analisadas. Este trabalho visou caracterizar mecanicamente a região s
Soldag. insp.. Publicado em: 02/12/2019
-
3. Mechanical behavior of PVD coatings deposited on ADI
ABSTRACT In this work, the mechanical behavior of the coated ADI system is studied. For this purpose, single layer Ti and bilayer Ti/TiN and TiAl/TiAlN coatings, with different thicknesses, were deposited by the PVD technique of cathodic arc deposition on high strength ADI substrates using industrial and experimental devices. The characterization of the coat
Matéria (Rio J.). Publicado em: 25/11/2019
-
4. Roasting soybeans in a microwave for manufacturing chocolate dragées
RESUMO: Este estudo objetivou avaliar o efeito do tempo de torra no micro-ondas para diferentes tamanhos de grãos de soja tipo alimento de tegumento preto, de forma a atingir a melhor crocância, sabor e dureza, e em seguida caracterizar o seu confeito, estruturado na forma de núcleo e camadas de cobertura de chocolate (drageados), em relação ao valor n
Cienc. Rural. Publicado em: 05/09/2019
-
5. Effects of Gas Nitriding on Fatigue and Crack Initiation of Ti6Al4V produced by Selective Laser Melting
Selective laser melting (SLM) is an additive manufacturing technique which permits fabrication of three dimensional parts by selectively melting consecutive layers of metallic powder. This allows the production of parts with high geometrical complexity. Titanium alloy Ti-6Al-4V (Ti64) is widely used in industry due to its high strength-to-mass ratio, corrosi
Mat. Res.. Publicado em: 15/07/2019
-
6. Microstructure and Wear Resistance of ZrC-ZrB2 /Ni Composite Coatings Prepared by Plasma Transferred Arc Cladding
The ZrC-ZrB2/Ni metal matrix composite coatings were in-situ synthesized from a mixture of Ni, Zr and B4C by plasma transferred arc (PTA) cladding process. Microstructures and phase constituents of the coatings were characterized by electron probe micro-analyzer (EPMA) and X-ray diffraction (XRD). Microhardness and wear resistance of the coatings were system
Mat. Res.. Publicado em: 06/05/2019
-
7. Influence of Forging Pressure on Microstructural and Mechanical Properties Development in Linear Friction Welded Al-Cu Dissimilar Joint
Abstract Dissimilar AA5083 and C101 pure copper linear friction welds were prepared using different forging pressures (60 MPa, 80 MPa, and 110 MPa) to investigate the influence of the forging pressure on the microstructural and mechanical properties development using optical microscopy (OM), scanning electron microscopy (SEM), hardness measurements, and ten
Soldag. insp.. Publicado em: 18/04/2019
-
8. Optimization of Multiple Performance Characteristics of Friction Stir Welded Joint with Grey Relational Analysis
In the present work, multi-objective optimization of the input welding parameters influencing the quality of weld joint of AA 5052 H32 aluminium alloy by FSW process is investigated using response surface methodology and grey relational analysis. The quality of the welded joint is measured based on the higher value of tensile strength and hardness of the joi
Mat. Res.. Publicado em: 08/11/2018
-
9. Characterization of Phase Transformations and Microstructural Changes in an API 5CT L80 Steel Grade During Ni Alloy Laser Cladding
The superficial coatings in micro-alloyed steel pipes has been a pointed way to decrease the corrosion problems in oil and gas industry. However, little emphasis has been given to the substrate. The effects of the deposition method on the steel microstructure and properties are still not well described. In this context, this work studied the effect of Ni sup
Mat. Res.. Publicado em: 26/07/2018
-
10. Production of Ba2AlNbO6 Ceramics and Study of their Stability in Crude Petroleum for the Conservation of Metallic Sensing Elements Used in Petroleum Extraction
In the present work niobium based complex cubic perovskite oxide Ba2AlNbO6 ceramics were produced, characterized and their stability in crude petroleum environment was studied for inert ceramic embedding used in petroleum extraction. Ba2AlNbO6 ceramic powder was prepared by means of thermo-mechanical processing. Structural characteristics of calcined materia
Mat. Res.. Publicado em: 26/07/2018
-
11. Boro-Austempering Treatment of Ductile Cast Irons
Samples of ductile cast irons alloyed with Cu, Cu-Ni and Cu-Ni-Mo were austempered, borided and boro-austempered and characterized for hardness and micro-adhesive wear behavior. The kinetics of layer formation was also studied. The boriding method used was molten borax bath, in periods of 2 and 4 hours at temperatures of 850, 900 and 950 ºC. The direct aust
Mat. Res.. Publicado em: 16/07/2018
-
12. The influence of Nano-TiO2 and Nano-Al2O3 Particles in Silicate Based Electrolytes on Microstructure and Mechanical Properties of Micro Arc Coated Ti6Al4V Alloy
Ceramic oxide coatings were fabricated on Ti6Al4V alloy by micro arc oxidation (MAO) in silicate electrolytes, with nano-TiO2 and nano-Al2O3 and without nano-additives. Effects of nano additives on the structural and mechanical properties of the MAO coatings were analysed. The MAO coatings were investigated by scanning electron microscopy (SEM), Energy-Dispe
Mat. Res.. Publicado em: 18/06/2018