Metallic Film
Mostrando 1-12 de 59 artigos, teses e dissertações.
-
1. Morphology Behavior of Copper Films Deposited after Wet Surface Treatment on Polished Alumina
In this paper, a pre-treatment process for electroless copper (Cu) deposition on the polished alumina (Al2O3) 99.9% and the behavior of Cu plating by electroless process after Al2O3 surface treatment were explored. Our work was carried out by changing the roughness of Al2O3 through micro-etching (coarsening), nucleation its surface by a two-step method (sens
Journal of the Brazilian Chemical Society. Publicado em: 2022
-
2. Boosting the Photocurrent of the WO3/BiVO4 Heterojunction by Photoelectrodeposition of the Oxy-Hydroxide-Phosphates Based on Co, Fe, or Ni
Here we investigated the photoelectrodeposition of oxygen-evolving catalysts (OECs) based on oxy-hydroxides-phosphates of Co, Fe, or Ni (CoPi, FePi, and NiPi) on the WO3/BiVO4 heterojunction and their activity in water oxidation. The OECs were deposited by cycles of (i) open-circuit potential (OCP) and (ii) applying a potential positive enough to oxidize the
Journal of the Brazilian Chemical Society. Publicado em: 2022
-
3. A SIMPLE GREEN REDUCTION STRATEGY TO SUBSTITUTE CADMIUM IN ANALYTICAL REDUCTION OF NITRATE IN GRIESS–ILOSVAY METHOD
Nitrate is an abundant ion that is present in many industrialized products and the environment. Various analytical methods have been described using the Griess-Ilosvay reagent for the determination of nitrate in different matrices after its reduction to nitrite, in most cases with metallic cadmium as the reducer. This work proposes a new method using aluminu
Quím. Nova. Publicado em: 2021-02
-
4. Metallic Phthalocyanines: impact of the film deposition method on its supramolecular arrangement and sensor performance
Abstract This short review gives a concise overview of the impact of deposition methods on the supramolecular arrangement of metallic phthalocyanine films and their applications. Primarily, an introduction about the possible phthalocyanine molecular structures and derivatives obtained from modification on the phthalocyanine rings was presented. The possibili
An. Acad. Bras. Ciênc.. Publicado em: 25/11/2019
-
5. Avaliação dos processos de fratura em filmes finos através da simulação de ensaios de indentação com penetradores esféricos
RESUMO Recentes trabalhos propõem a utilização dos ensaios de indentação como uma ferramenta capaz de avaliar características mecânicas de filmes finos, assim como avaliar possíveis falhas em sistemas que conjugam filmes de alta dureza depositados em substratos metálicos em solicitações tribológicas. Entretanto, a implementação da técnica de i
Matéria (Rio J.). Publicado em: 25/11/2019
-
6. Effect of High-pressure Torsion on Corrosion Behavior of a Solution-treated Al-Mg-Sc Alloy in a Saline Solution
The effect of the increase in crystalline defects in the structure generated by high-pressure torsion (HPT) on the corrosion behavior of metallic materials is not well understood. This report evaluates the influence of HPT on the corrosion behavior of a solution treated Al-3wt% Mg-0.2wt% Sc alloy in a 3.5 wt./v.% NaCl solution. The electrochemical behavior o
Mat. Res.. Publicado em: 04/11/2019
-
7. A New Conductive Ink for Microstrip Antenna and Bioinspired FSS Designs on Glass and Fiberglass Substrates
Abstract This paper describes an investigation of the possibility of using a new conductive ink, insted of copper clad laminates, in the manufacturing of microstrip patch antennas on glass and fiberglass substrates and of bioinspired frequency selective surfaces (FSSs) on fiberglass substrates for wireless communication systems. The new conductive ink is dev
J. Microw. Optoelectron. Electromagn. Appl.. Publicado em: 19/06/2019
-
8. Comportamento da corrosão microbiológica do aço duplex com aplicação de sais de quaternário de amônio
RESUMO A corrosão microbiológica tem causado diversos prejuízos para variados segmentos industriais que utilizam os materiais metálicos em seus sistemas. Uma forma de minimizar e até mesmo controlar os problemas causados pela corrosão microbiológica tem sido a aplicação de biocidas nestes sistemas. Neste trabalho, a corrosão microbiológica do aço
Matéria (Rio J.). Publicado em: 20/05/2019
-
9. Influência da densidade de potência e da porcentagem de N2 na atmosfera de deposição na dureza e no módulo de Young em filmes de aço inoxidável AISI 316 depositados por pulverização catódica
RESUMO O processo de recobrimento por pulverização catódica é uma técnica amplamente utilizada para produção de revestimentos metálicos e cerâmicos, devido a versatilidade no controle das propriedades com pequenas mudanças nos parâmetros de processo, como densidade de potência aplica ao cátodo magnetron e atmosfera de trabalho. Sendo assim, as p
Matéria (Rio J.). Publicado em: 20/05/2019
-
10. Al-doping and Properties of AZO Thin Films Grown at Room Temperature: Sputtering Pressure Effect
Aluminum zinc oxide (AZO) thin films were synthesized on glass substrates by radio frequency (rf) magnetron sputtering from a metallic Zn-Al (5 at. %) target at room temperature. The morphological, structural, electrical and optical properties of the films were studied as a function of the sputtering pressure, which was varied from 0.1 to 6.7 Pa. X-ray diffr
Mat. Res.. Publicado em: 09/05/2019
-
11. Efecto de la concentración del silano MTMO sobre la protección contra la corrosión de acero electrocincado
ABSTRACT Superficial pretreatments based on silanes are one of the prominent alternatives to replace chromates as temporary protectors from the action of aggressive environments to metallic substrates. The barrier effect afforded by the silane film makes porosity, thickness and film homogeneity important issues in the protective effect. In the present work,
Matéria (Rio J.). Publicado em: 19/07/2018
-
12. Determination of Film Thickness Through Simulation of Vickers Hardness Testing
In recent decades, changes in the surface properties of materials have been used to improve their tribology characteristics. However, this improvement depends on the process, treatment time and, essentially, the thickness of this surface film layer. Physical vapor deposition (PVD) has been used to increase the surface hardness of metallic materials. The aim
Mat. Res.. Publicado em: 13/04/2017