Metallic Alloys
Mostrando 1-12 de 133 artigos, teses e dissertações.
-
1. Morphology, Crystalline Structure and Chemical Composition Of MAO Treated Ti-15Zr-Mo Surfaces Enriched with Bioactive Ions
In this study, MAO treatment was used to enrich, with bioactive Ca, Mg and P atoms, as-casted and heat-treated Ti-15Zr-xMo (x = 0, 5, 10 and 15 wt%) alloys, for potential use as advanced metallic biomaterials. The chemical composition of the surface was evaluated by EDS and XPS measurements. The morphology and microstructure was analyzed by OM and SEM images
Mat. Res.. Publicado em: 09/12/2019
-
2. Potencial antimicrobiano de diferentes retentores intrarradiculares frente a Enterococcus faecalis: uma avaliação in vitro
Resumo Introdução O tratamento endodôntico tem como objetivo erradicar microrganismos bacterianos e fúngicos do canal radicular, ou pelo menos possibilitar sua redução para níveis compatíveis com a saúde do tecido perirradicular, uma vez que, após o tratamento endodôntico, colônias de microrganismos residuais podem estar presentes nos túbulos d
Rev. odontol. UNESP. Publicado em: 23/09/2019
-
3. Comparison of Aluminum Based Alloys Reinforced with Intermetallic Developed by Powder Metallurgy and Arc Melting Routes
Abstract In this work, Al-Ti alloys were prepared using metallic powders of Al and Ti via Powder Metallurgy (PM) and Arc Melting (AM) route. Four chemical compositions including pure aluminum were studied. Metallic powders were mixed with three compositions, Al-5Ti, Al-10Ti and Al-10Ti-2SiC. All the compositions were in atomic percentage. In case of PM, samp
Soldag. insp.. Publicado em: 29/08/2019
-
4. Nanoporous Pd with Tunable Pore Size prepared by Dealloying Pd 30Cu40Ni10P20 Metallic Glass and Their Catalytic Performance
This work reports the formation of nanoprous Pd with tunable pore size and high stability by dealloying Pd30Cu40Ni10P20 metallic glass. The results show that lower dealloying temperature results in smaller pore size while the dealloying duration does not cause distinct change in the porous structure, even at an ambient dealloying temperature. The glassy stru
Mat. Res.. Publicado em: 10/06/2019
-
5. Influência da microestrutura na resistência ao desgaste microabrasivo de ligas de F-Cr-C e Fe-Cr-C-Nb
ABSTRACT Neste trabalho é feita uma avaliação da influência do teor de cromo e da combinação do cromo e nióbio em ligas de revestimento duro do tipo Fe-Cr-C, na microestrutura e propriedades que envolvam a resistência ao desgaste microabrasivo. Vários estudos têm sido realizados em busca de informações conclusivas sobre este sistema em condiçõe
Matéria (Rio J.). Publicado em: 20/05/2019
-
6. Crystallization Behavior and Mechanical Properties of Cu-based Bulk Metallic Glass Composites
This work highlights the relationship between the preparation, crystallization behavior, microstructures, and mechanical properties of Cu-based bulk metallic glasses (BMGs) and their composites (BMGCs). (Cu47Zr45Al8)97.5Y1.5Nb in-situ BMGCs were prepared using isothermal annealing, and the experimental results indicate tunable mechanical properties of the al
Mat. Res.. Publicado em: 06/05/2019
-
7. Recent Topics on the Structure and Crystallization of Al-based Glassy Alloys
Al-based glassy alloys (metallic glasses) have been of great scientific and technological interest as a high specific strength and high corrosion resistant materials. However, the low glass-forming ability (GFA) is still a choke point that greatly influences the applications. In order to further comprehend the glass formation mechanism and investigate the po
Mat. Res.. Publicado em: 28/02/2019
-
8. Influence of Copper and Metallic Alloys on the Oxidation Reaction of Commercial Biodiesel in Mixture with Natural Antioxidant
The purpose of this research was to evaluate the influence of metallic alloys and copper in the degradation of biodiesel in mixture with blackberry extract. Biodiesel is formed by unsaturated esters highly susceptible to the oxidation reaction. The initial induction period (IP) of the control sample was 9.53 h and, after 208 days, the IP reduced to 5.74 h. H
J. Braz. Chem. Soc.. Publicado em: 2019-01
-
9. Influence of Small Content Elements Additions on the Glass Forming Ability of Zr-based Bulk Metallic Glasses Alloys
The present work reports investigation on the Glass Forming Ability (GFA) of Zr-based Bulk Metallic Glasses (BMG’s) by microalloying with early transition metals. GFA was measured as the amorphous fraction formed in samples with different diameters using optical microscopy (OM) and image analysis techniques. Samples with the highest GFA had their oxygen co
Mat. Res.. Publicado em: 06/09/2018
-
10. Esfuerzo de corte en Interfaces Fe/Fe3O4
Abstract The mechanical stability of oxides formed on metallic alloys is a key concern in the determination of component susceptibility to the medium in contact and the applicability of the alloy to high temperatures and other extreme conditions. In this context, the energy of adhesion is a key parameter. Density functional Theory (DFT) and other atomistic m
Matéria (Rio J.). Publicado em: 19/07/2018
-
11. Estudio de la formabilidad en caliente de aleaciones de titanio a través del ensayo de torsión y su aplicación a la optimización de procesos de forja y extrusión
ABSTRACT In the development of hot metal forming, the metallic products must comply with the requirements imposed by current standards. In some cases, the required microstructure can only be obtained through thermomechanical processing. With titanium and its alloys, small ranges of good workability are an additional difficulty. In this work the hot-workabili
Matéria (Rio J.). Publicado em: 19/07/2018
-
12. An Experimental Study of the Solidification Thermal Parameters Influence upon Microstructure and Mechanical Properties of Al-Si-Cu Alloys
Metals solidification involves the transformation of the molten metal back into the solid state. Solidification structures impact heavily on the final product's characteristics. The microstructure effects on metallic alloys properties have been highlighted in various studies and particularly the dendrite arm spacing influence upon the mechanical properties s
Mat. Res.. Publicado em: 18/06/2018