Metal Cutting Tools
Mostrando 1-12 de 28 artigos, teses e dissertações.
-
1. Influência do material da ferramenta de corte sobre a usinabilidade do aço ABNT 4340 no torneamento
RESUMO No presente trabalho procurou-se compreender os fenômenos associados à usinagem do aço ABNT 4340 utilizando ferramentas de corte de metal duro e cermet, ambas com geometria do quebra-cavaco para usinagem leve (LP) e média (MP). Nesse sentido, analisou-se a influência da variação do avanço, quebracavaco e o material da ferramenta de corte nos p
Matéria (Rio J.). Publicado em: 16/09/2019
-
2. Influência do material da ferramenta de corte sobre a usinabilidade do aço ABNT 4340 no torneamento
RESUMO No presente trabalho procurou-se compreender os fenômenos associados à usinagem do aço ABNT 4340 utilizando ferramentas de corte de metal duro e cermet, ambas com geometria do quebra-cavaco para usinagem leve (LP) e média (MP). Nesse sentido, analisou-se a influência da variação do avanço, quebracavaco e o material da ferramenta de corte nos p
Matéria (Rio J.). Publicado em: 20/05/2019
-
3. Investigation on the Effect of Different Pre-Cracking Methods on Fracture Toughness of RT-PMMA
Abstract In this study, eight techniques including coping saw, metal slitting saw, razor blade, cubic boron nitride (CBN) disc, scoring, die-cutting and guillotining, diamond disc, and laser cutting methods were used to produce pre-cracked fracture toughness (Kc) test specimens made of poly(methyl methacrylate)/graft-acrylonitrile butadiene styrene blends. T
Lat. Am. j. solids struct.. Publicado em: 2016-11
-
4. Effect of Solid-State Laser Parameters on the Surface's Topography Formation During Texturization of Hard Metal Cutting Tools
ABSTRACT: The objective of this paper is to analyze the influence of specific laser system parameters on the microstructure of the ring formation process on the hard metal tool's surface. The parameters analyzed were: working distance, incident beam power and tool surface treatment, flank and rake. The microstructures were analyzed with regard to its diamete
J. Aerosp. Technol. Manag.. Publicado em: 2015-03
-
5. Influence of graphite particles on surface roughness and chip formation studies in turning metal matrix composites
This study presents an experimental investigation on surface roughness and chip formation in turning of Al 2219/15SiCp and Al 2219/15SiCp-3Gr (hybrid) composites. Experiments were conducted with different cutting conditions using carbide, coated carbide and polycrystalline diamond (PCD) tools. The results reveal that the surface roughness values are less for
Mat. Res.. Publicado em: 25/06/2013
-
6. Design of a computer aided quick-stop device for study of dead metal zone formation
The use of quick-stop device allows observing a sequence of frozen images focused on the chip formation area when machining in orthogonal turning tests. This work records the development of a quick-stop device employing a servo motor. The present invention relates generally to a quick stop device, for combination with a cutting machine that is able to abrupt
J. Braz. Soc. Mech. Sci. & Eng.. Publicado em: 2012-12
-
7. Slip-line metal cutting model with negative rake angle
A small dead region is seen in front of the rake face of the tool during cutting with negative rake. The lack of knowledge about the stagnant region in the cutting with negative rake requires researching new models. In this work, cutting mechanism of the metal cutting with negative rake angle tools and the stagnation zone formation were studied. A model was
J. Braz. Soc. Mech. Sci. & Eng.. Publicado em: 2012-09
-
8. Fresamento com ar quente: uma proposta para minimizar a formação de trincas térmicas em ferramentas de metal duro
This work presents the results, analyses and conclusions about a study carried out with objective of minimizing the thermal cracks formation on cemented carbide inserts during face milling. The main focus of investigation was based on the observation that milling process is an interrupted machining process, which imposes cyclic thermal loads to the cutting t
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 29/07/2011
-
9. Estudo do desempenho de ferramenta de corte no processo de mandrilamento em ferro fundido vermicular - CGI / Performance of the cutting tools in the boring machining process vermicular cast iron - CGI
Existe hoje uma tendência no mercado de veículos de motor diesel a fabricarem os blocos dos motores em ferro fundido vermicular devido à melhor eficiência de combustão e maior resistência à compressão, permitindo paredes de galerias mais finas com conseqüência na redução do peso do bloco, quando comparado ao bloco usual feito de ferro fundido cin
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 08/07/2011
-
10. Estudos do nível de utilização de sistemas de gerenciamento de ferramentas de corte em empresas de maquinas e implementos agrícolas. / Study of the level of use of Management System Cutting Tools in Enterprises of Machinery and Agricultural Implements
No atual cenário mundial o Agronegócio vem despontando como um mercado crescente principalmente para o Brasil. No intuito de acompanhar este crescimento as Empresas de Máquinas e Implementos Agrícolas (EMIA) estão aumentando a cada ano sua capacidade de produção metal-mecânica. À medida que as EMIA aumentam sua produção todos os insumos usados no
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 01/03/2011
-
11. Estudo da influência do lubrificante sólido MoS2 nas propriedades de revestimentos protetores de TiN
Neste trabalho investigou-se o revestimento protetor nitreto de titânio com a incorporação de dissulfeto de molibdênio como lubrificante sólido, visando aplicação em peças e ferramentas de corte na indústria metal-mecânica. Este revestimento foi obtido na forma de filme fino pela técnica de magnetron sputtering reativo modificando a quantidade de
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 30/08/2010
-
12. Evaluation of the adhesion strength of diamond films brazed on K-10 type hard metal
The coating of cutting tools with diamond films considerably increases the tool performance due to the combination of the unique tribological properties of diamond with the bulk properties of the substrate (toughness). The tool performance, however, is strongly related to the adhesion strength between the film and the substrate. In this work our main goal wa
Publicado em: 2010