Machining Tools
Mostrando 1-12 de 69 artigos, teses e dissertações.
-
1. Influência do material da ferramenta de corte sobre a usinabilidade do aço ABNT 4340 no torneamento
RESUMO No presente trabalho procurou-se compreender os fenômenos associados à usinagem do aço ABNT 4340 utilizando ferramentas de corte de metal duro e cermet, ambas com geometria do quebra-cavaco para usinagem leve (LP) e média (MP). Nesse sentido, analisou-se a influência da variação do avanço, quebracavaco e o material da ferramenta de corte nos p
Matéria (Rio J.). Publicado em: 16/09/2019
-
2. Performance and Surface Integrity of Wire Electrical Discharge Machining of Thin Ti6al4v Plate Using Coated and Uncoated Wires
Wire Electrical Discharge Machining (WEDM) is one of the most important production technologies to manufacture very accurate small components and tools on any electrical conductive material. Titanium and its alloys have been widely used in automobile and aerospace industry as well as in medical engineering field. Small components and tools with complex geome
Mat. Res.. Publicado em: 03/06/2019
-
3. Influência do material da ferramenta de corte sobre a usinabilidade do aço ABNT 4340 no torneamento
RESUMO No presente trabalho procurou-se compreender os fenômenos associados à usinagem do aço ABNT 4340 utilizando ferramentas de corte de metal duro e cermet, ambas com geometria do quebra-cavaco para usinagem leve (LP) e média (MP). Nesse sentido, analisou-se a influência da variação do avanço, quebracavaco e o material da ferramenta de corte nos p
Matéria (Rio J.). Publicado em: 20/05/2019
-
4. Surface Integrity Analisys in the Hard Turning of Cemented Steel AISI 4317
This work was based on the surface integrity analysis of hardened steel, AISI 4317 case carburized, quenched and tempered with 58 HRC, obtained by a turning operation executed with CBN (cubic boron nitride) tool, varying three basic cutting parameters (cutting speed, feed rate and cutting depth). The surface integrity characterization was conducted analyzing
Mat. Res.. Publicado em: 26/07/2018
-
5. Investigation of High-Speed Cryogenic Machining Based on Finite Element Approach
Abstract The simulation of cryogenic machining process because of using a three-dimensional model and high process duration time in the finite element method, have been studied rarely. In this study, to overcome this limitation, a 2.5D finite element model using the commercial finite element software ABAQUS has been developed for the cryogenic machining proc
Lat. Am. j. solids struct.. Publicado em: 2017-03
-
6. Surface Integrity Analysis in Machining of Hardened AISI 4140 Steel
This study aimed to analyze the residual stresses and roughness in finishing milling of AISI 4140 steel, quenched and tempered up to hardness of 58 HRC. Machining operations were performed with the use of CBN inserts and by varying three basic cutting parameters (cutting speed, feed per tooth and cutting depth). Hardened materials are typically machined by a
Mat. Res.. Publicado em: 23/01/2017
-
7. Machinability Evaluation in Hard Milling of AISI D2 Steel
Milling of hardened steel components provides considerable benefits in terms of reduced manufacturing cost and time compared to traditional machining. Temperature variation in milling is an important factor affecting the wear of cutting tools. The poor selection of milling parameters may cause excessive tool wear and increased work surface roughness. Hence,
Mat. Res.. Publicado em: 01/03/2016
-
8. Influence of graphite particles on surface roughness and chip formation studies in turning metal matrix composites
This study presents an experimental investigation on surface roughness and chip formation in turning of Al 2219/15SiCp and Al 2219/15SiCp-3Gr (hybrid) composites. Experiments were conducted with different cutting conditions using carbide, coated carbide and polycrystalline diamond (PCD) tools. The results reveal that the surface roughness values are less for
Mat. Res.. Publicado em: 25/06/2013
-
9. Avaliação de diferentes ferramentas no torneamento da liga Inconel 713C / Evaluation of different tools in turning of Inconel 713C
The super alloy Inconel 713C is an alloy whose main element of its composition is nickel. The combination of high levels of this element and the structure of this material makes it very difficult to be transformed by the machining process. Because of this difficulty and lack of information about the machining of this material, the purpose of this study was t
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 27/02/2012
-
10. Design of a computer aided quick-stop device for study of dead metal zone formation
The use of quick-stop device allows observing a sequence of frozen images focused on the chip formation area when machining in orthogonal turning tests. This work records the development of a quick-stop device employing a servo motor. The present invention relates generally to a quick stop device, for combination with a cutting machine that is able to abrupt
J. Braz. Soc. Mech. Sci. & Eng.. Publicado em: 2012-12
-
11. Machinability study of steels in precision orthogonal cutting
The miniaturization of components and systems is advancing steadily in many areas of engineering. Consequently, micro-machining is becoming an important manufacture technology due to the increasing demand for miniaturized products in recent years. Precision machining aims the production of advanced components with high dimensional accuracy and acceptable sur
Materials Research. Publicado em: 03/07/2012
-
12. Influence of a diagonal pre-drilled hole on hole quality during the reaming process using multiblade tools
The requirements of production engineering for a precision hole are to ensure the required quality as well as minimal production costs. The interactions between machine, tool and the pre-drilled hole result in uncertainties during the final reaming process. For this purpose the reaming process itself and the appearance of process faults were focused in a lar
J. Braz. Soc. Mech. Sci. & Eng.. Publicado em: 2012