Interface Of Adhesion
Mostrando 13-24 de 134 artigos, teses e dissertações.
-
13. Synthesis of Vanadium Interface for HFCVD Diamond Deposition on Steel Surface
Laser cladding of vanadium carbide powder developed an interlayer on AISI D6 steel as a diffusional barrier and to relief thermal residual stress. Laser cladding experiments varied resolution (DPI) and scanning speed (mm/s). CVD diamond deposition on this interface went on by HFCVD technique. The coatings were characterized by X-ray diffraction analysis (XRD
Mat. Res.. Publicado em: 06/07/2017
-
14. Electrical and microstructural characterization of Gd-doped Ceria/Y-doped Zirconia bi-layer electrolyte prepared by tape casting
ABSTRACT GDC-YSZ bi-layer SOFC electrolytes are an interesting manner to protect GDC electrolytes of the low oxygen partial pressure present at anode-electrolyte interface. This oxygen partial pressure condition and high temperatures during the operation of SOFC permit GDC electrolyte reduction injuring the performance of SOFC. In this work, GDC-YSZ bi-layer
Matéria (Rio J.). Publicado em: 22/05/2017
-
15. TIMBER BEAM REPAIR BASED ON POLYMER-CEMENTITIOUS BLENDS
ABSTRACT This study aims to manufacture and apply polymer-cementitious blends based on a combination of epoxy polymer and Ordinary Portland Cement (OPC) for timber beam repair. The material was used to repair timber beams of “Maçaranduba” (Manilkara sp.) and “Cedro doce” (Cedrella spp) wood species. A full factorial design was conducted to investiga
Eng. Agríc.. Publicado em: 2017-04
-
16. Dip coating of a carbon steel sheet with Ni reinforced TiO2 nanoparticles
In this work carbon steel plates were dip-coated with a composite film obtained from a colloidal suspension of Ni-TiO2. Suspensions with different solids contents were used to evaluate the adherence of the film and the microstructural features. The samples were characterized using both optical and scanning electron microscopy, energy dispersive spectroscopy
Mat. Res.. Publicado em: 12/04/2016
-
17. Flexible thermoplastic composite of Polyvinyl Butyral (PVB) and waste of rigid Polyurethane foam
This study reports the preparation and characterization of composites with recycled poly(vinyl butyral) (PVB) and residue of rigid polyurethane foam (PUr), with PUr contents of 20, 35 and 50 wt %, using an extruder equipped with a Maillefer single screw and injection molding. The components of the composites were thermally characterized using differential sc
Polímeros. Publicado em: 2015-04
-
18. Surface characterization and osteoblast-like Cells culture on collagen modified PLDLA scaffolds
Surface modification techniques based on the grafting of chemical functional groups and immobilization of bioactive molecules have been used to improve biocompatibility and clinical performance of bioabsorbable scaffolds in tissue engineering and medicine regenerative applications. This study aimed at developing and characterizing a biomimetic surface to sti
Mat. Res.. Publicado em: 2014-12
-
19. Treatments of jute fibers aiming at improvement of fiber-phenolic matrix adhesion
Composites based on a thermoset phenolic matrix and jute fibers were prepared and characterized. The fibers were alternatively treated with ionized air or aqueous alkaline solution (mercerization) with the aim of introducing changes in the morphology, dispersive component of surface free energy, γS D (estimated by Inverse Gas Chromatography, IGC) and the ac
Polímeros. Publicado em: 2014-08
-
20. Influence of microhybrid resin and etching times on bleached enamel for the bonding of ceramic brackets
The aim of this study was to evaluate the shear bond strength (SBS) of polycrystalline ceramic brackets (PCB) bonded after bleaching treatment using different composite resins and enamel etching times. A total of 144 bovine incisors were randomly divided into two study groups (n = 72, each) as follows: G1, enamel bleached with 35% hydrogen peroxide, and G2 (
Braz. oral res.. Publicado em: 2013-04
-
21. XPS, XRD and laser raman analysis of surface modified of 6150 steel substrates for the deposition of thick and adherent diamond-like carbon coatings
Although the 6150 steel has an excellent fatigue and impact resistance, it is unsuitable to operate it when the corrosion is a limited factor. We propose here a sequence of steel pre-treatment by carburizing, carbonitriding and nitriding in order to improve the poor adhesion between Diamond Like-Carbon coatings on steel. This sequence is our attempt to reduc
Mat. Res.. Publicado em: 25/02/2013
-
22. Synthesis and characterization of Ni-Mo filler brazing alloy for Mo-W joining for microwave tube technology
A brazing process based on Ni-Mo alloy was developed to join porous tungsten cathode bottom and dense molybdenum cathode body for microwave tubes manufacture. The Ni-Mo alloy was obtained by mixing and milling powders in the eutectic composition, and applied on the surface of the components. The brazing was made at 1400 °C by using induction heating in hydr
Mat. Res.. Publicado em: 08/02/2013
-
23. Surface modification of recording electrodes
Waterborne Polyurethanes (PUs) are a family of polymers that contains urethane linkages synthesized in an aqueous environment and are thus free of organic solvents. Recently, waterborne PUs have been extensively studied for biomedical applications because of their biocompatibility. The present work investigates the following: (1) the impact on electrical per
Polímeros. Publicado em: 2013
-
24. Influência de materiais obturadores e agentes de limpeza na resistência da união e interface adesiva de pinos de fibra de vidro à dentina intrarradicular / Influence of filling materials and cleaning agents on bond strength and adhesion interface of glass fiber post to radicular dentin
The aim of this in vitro study was to evaluate the post-cement-dentin adhesive interface quality and the effect of different filling materials and cleaning agents on the bond strength of glass fiber posts to primary root dentin. This study included 156 roots of bovine primary teeth which were endodontically treated and assigned to four groups (39 teeth each
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 28/02/2012