Inserts
Mostrando 13-24 de 1183 artigos, teses e dissertações.
-
13. An Investigation on Surface Roughness and Tool Wear in Turning Operation of Inconel 718
ABSTRACT: This paper investigates the influences of three different input parameters, such as feed rate, insert nose radius, and insert coating methods, in the turning operation of Inconel 718. The coating methods were selected as medium temperature chemical vapor deposition (MT-CVD) and physical vapor deposition (PVD) and in addition to coating methods, the
J. Aerosp. Technol. Manag.. Publicado em: 25/02/2019
-
14. Uso de medicamentos antidepressivos na amamentação: avaliação da conformidade das bulas com fontes bibliográficas baseadas em evidências científicas
O objetivo deste artigo foi avaliar a conformidade entre as recomendações de uso de medicamentos antidepressivos durante a amamentação, presentes em bulas, e as recomendações de fontes bibliográficas baseadas em evidências científicas. Foram avaliadas as bulas padrão de 23 antidepressivos com registro ativo no Brasil. A presença de contraindicaç�
Cad. Saúde Pública. Publicado em: 18/02/2019
-
15. Medicalização, diagnóstico clínico e queixa-conduta – redes de significação em jogo
Este artigo faz emergir uma rede discursiva entre o processo de medicalização, o funcionamento discursivo do diagnóstico clínico na contemporaneidade e um funcionamento particular de clínica médica sustentado por um atendimento do tipo queixa-conduta. Empreendendo uma Análise Discursiva, percorremos movimentos de sentido constitutivos da história da
Interface (Botucatu). Publicado em: 16/01/2019
-
16. Synthetic granite composite for precision equipment structures
ABSTRACT The structure is a component that plays an extremely important role in the equipment’s performance, it must withstand efforts without compromising the function, receive and transfer heat, dampen vibrations and position the elements, as well as promote ergonomics and aesthetics. In lightweight and precision equipment’s the raw material used must
Matéria (Rio J.). Publicado em: 06/12/2018
-
17. Heat Treatment of Sintered Valve Seat Inserts
The characterization of sintered valve seat inserts (VSIs) after being subjected to different heat treatment operations has been carried out. The VSIs were obtained from three different alloys by mixing iron powder with AISI M3:2, AISI M2 high-speed steels, and AISI D2 tool steel. After sintering, the VSI were quenched in air followed by double tempering at
Mat. Res.. Publicado em: 02/08/2018
-
18. Numerical Study On Multi Layered Target Material Subjected To Impact Loading
Abstract In this study, the glass/epoxy composite laminate is layered with polyurethane foam/ polyurethane sheet and silicon carbide to analyse their response during high mass and low velocity impact. The silicon carbide is layered in two forms, one is as plate and the other is as inserts. The target materials are prepared in various combinations and the bo
Lat. Am. j. solids struct.. Publicado em: 04/06/2018
-
19. The Effect of Cr3C2 and TaC Additives on Microstructure, Hardness and Fracture Toughness of WC-6Co Tool Material Fabricated by Spark Plasma Sintering
Spark plasma sintering has been used to successfully produce WC-6Co-xCr3C2, WC-6Co-xTaC (x = 0.2, 0.6, 1.0) and WC-6Co-xCr3C2-xTaC (x = 0.1, 0.3, 0.5) cemented carbides. The spark plasma sintered compacts were investigated by scanning electron microscopy, hardness tests and fracture toughness tests. The results were compared to an additives-free WC-6Co cemen
Mat. Res.. Publicado em: 11/05/2017
-
20. Spark Plasma Sintering of a Hard Metal Powder Obtained from Hard Metal Scrap
Spark plasma sintering is used to consolidate a WC-Co powder produced from milled discharged hard metal cutting inserts. The powder was mixed to 10%wt Co powder and spark plasma sintered (SPS) under 80Mpa pressure, at 1200ºC with heating rate of 160ºC/min. A reference alloy was prepared with a commercial WC powder and 10%wt. Co under the same conditions. T
Mat. Res.. Publicado em: 13/03/2017
-
21. Surface Integrity Analysis in Machining of Hardened AISI 4140 Steel
This study aimed to analyze the residual stresses and roughness in finishing milling of AISI 4140 steel, quenched and tempered up to hardness of 58 HRC. Machining operations were performed with the use of CBN inserts and by varying three basic cutting parameters (cutting speed, feed per tooth and cutting depth). Hardened materials are typically machined by a
Mat. Res.. Publicado em: 23/01/2017
-
22. Anomalous Behavior of a Solid Rocket Motor Nozzle Insert During Static Firing Test
ABSTRACT This paper presents the study and development of a firing test used to evaluate the behavior of a solid rocket motor. The motivation for the development of a subscale solid rocket motor with end burning propellant grain geometry arose from the need to evaluate the nozzle inserts of graphite for the possible replacement with the carbon fiber-reinforc
J. Aerosp. Technol. Manag.. Publicado em: 2016-12
-
23. Response of a co-culture model of epithelial cells and gingival fibroblasts to zoledronic acid
Abstract Osteonecrosis of the jaw is an adverse effect of bisphosphonates. While the etiopathogenesis of this condition has been investigated, the interactions and effects of bisphosphonates on oral mucosa cells remain unclear. It is hypothesized that cell culture models, such as co-culture or three-dimensional cell culture models, can provide valuable insig
Braz. oral res.. Publicado em: 28/11/2016
-
24. Program for Contact Allergen Research (PPAC) - a new tool for dermatologists
Abstract: In Brazil there is no classification of dermatological products by the presence of vehicles with sensitizing potential. The objective of this study is to create a database to classify such products based on the absence of the selected allergens, aiming at making it available for medical consultation. We conducted an observational study, from the co
An. Bras. Dermatol.. Publicado em: 2016-06