Implant Biomechanics
Mostrando 13-24 de 29 artigos, teses e dissertações.
-
13. Avaliação por elementos finitos de tensões no tecido ósseo peri-implantar durante a osseointegração / Finite element analysis of stresses in peri-implant bone tissue during osseointegration
Forças aplicadas por próteses totais a implantes submersos durante o período deosseointegração podem, em alguns casos, levar ao insucesso clínico. Até o momento não existe trabalho na literatura que quantifique e/ou verifique a distribuição das forças mastigatórias em implantes submersos durante a ação mastigatória de próteses totais convenci
Publicado em: 2011
-
14. Effect of the number of abutments on biomechanics of Branemark prosthesis with straight and tilted distal implants
OBJECTIVE: This study aimed to evaluate the bending moments, and compressive and tensile forces in implant-supported prostheses with three, four or five abutments. MATERIAL AND METHODS: Ten Pd-Ag frameworks were tested over two master models with: 1) parallel vertical implants, and 2) tilted distal implants. Strain gauges were fixed on the abutments of each
Journal of Applied Oral Science. Publicado em: 2010-04
-
15. Evaluation of abutment and perimplantar region deformation of implant-supported screwed prostheses: an study using strain gauges / Avaliação da deformação do intermediário e região perimplantar de próteses implanto-suportada unitárias parafusada: estudo através da extensometria
The dental implant depends on the supporting bone for its stability and functional longevity. Mechanical behavior and trabecular bone structure affect the interface with the implant. Such knowledge may provide a basis for improvements in the current implant function and design, decreasing bone crest resorption and failure at bone-implant junction. Adequate q
Publicado em: 2010
-
16. Desajuste marginal e influencia na pre-carga de parafusos e nas tensões induzidas as fixações de pilares metaloplasticos sobre-fundidos / Marginal misfit and influence in the pre-load and the stress-induced setting of the metaloplastic abutments
Castable UCLA abutments are of wide applicability in dental implants, because they allow the manipulation in the laboratory at low cost and individualization of abutments for each patient. However, they show the worse results of marginal adaptation then the fabricated, although these aggregate costs significantly higher. UCLA premachined abutments for castin
Publicado em: 2010
-
17. ANÃLISE DE SISTEMAS DE IMPLANTES DENTÃRIOS EM MANDÃBULAS EDÃNTULAS COM APLICAÃÃO DE CARREGAMENTO IMEDIATO / Study of the systems of dental implantations for edentulous mandibula with immediate load
The present study aimed at obtaining comparative elements among the guided systems of fixed complete denture with 4 osseointegrated implants with immediate loading, considering the importance of understanding the implant project as a process where biomaterials and biomechanics are assessed. The three-dimensional finite element method was used to analyze the
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 30/10/2009
-
18. Avaliação da deformação gerada na região peri-implantar de prótese fixa implantossuportada, com a utilização de extensômetros lineares elétricos / Evaluation of peri-implant bone deformation of a mandibular cantilevered implant-supported prosthesis, with the use of strain gages
O comportamento mecânico das próteses parciais fixas implanto-suportadas são foco de vários estudos, onde o entendimento do processo de transmissão de forças mastigatórias e suas reações na estrutura óssea peri-implantar ainda não são totalmente compreendidos. Por isso, o objetivo deste trabalho foi verificar a deformação gerada na região peri
Publicado em: 2009
-
19. Mechanical behaviour of non passive multi unit implant restorations / Comportamento mecanico de restaurações multiplas implanto-retidas frente a presença de desajustes marginais
A obtenção de uma estrutura protética passivamente adaptada aos implantes e pilares de conexão tem sido sugerida como fundamental para se evitar falhas mecânicas e biológicas nas reabilitações implanto-retidas. Um melhor entendimento dos efeitos da deficiência de passividade poderia ajudar a entender a mecânica destas falhas. O objetivo desta tese
Publicado em: 2009
-
20. Analysis of alteration the number and diameter on stress transfer by protocols implant-supported prostheses / Analise das tensões na estrutura de suporte em protocolos implanto-suportados com alteração do numero e diametro das fixações
Este trabalho teve por objetivo quantificar e qualificar in vitro às tensões geradas pela da alteração do número e do diâmetro de implantes dentários em protocolos clássicos tipo Brånemark, em implantes fixados em modelo aproximado da região anterior da mandíbula, entre os forames mentonianos por meio da técnica da fotoelasticidade. Foram confecc
Publicado em: 2008
-
21. Estudo biomecânico do comportamento de diferentes espessuras de capa de cimento ósseo em novo modelo de prótese modular diafisária femoral em cão submetidas a ensaio de torção / Biomechanical analysis in the use of different cement layers in a new model of modular diaphyseal femoral implant relative to torsion forces
A viabilidade da utilização de próteses modulares cimentadas em diáfises de fêmur em cães foi demonstrada, porém diversos autores relatam a falha de aderência entre as próteses e os ossos como uma das principais complicações. O presente trabalho teve como objetivo investigar biomecanicamente a interface implante metálico, osso e capa de cimento �
Publicado em: 2008
-
22. Length of implant, type of connection and splinttation, influence in the tensions distribution in posterior partial prosthesis : photoelastic analysis / Influencia do comprimento, da ferulização e do tipo de conexão de implantes na distribuição de tensões em proteses parciais posteriores : analise fotoelastica
A partir de moldes de silicone foram confeccionados oito modelos em resina fotoelástica (Araldite, Huntsman, São Paulo, Brasil), distribuídos um para cada grupo composto da seguinte forma: (G1) três coroas ferulizadas sobre implantes hexágono externo de 5,0 Ø x 7mm (Titamax Ti, Neodent, Curitiba, Brasil); (G2) três coroas unitárias sobre implantes he
Publicado em: 2008
-
23. 3d analysis of stress distribuition on bar/clips structure and bone implant interface due to bar material and vertical misfit to dental implant / Analise tridimensional da distribuição de tensões na estrutura do sistema barra/clips e interface osso/implante em função do tipo de material da barra e do desajuste vertical aos implantes
Este trabalho verificou tridimensionalmente a distribuição de tensões na estrutura e interface osso/implante do sistema barra/clips sobre dois implantes osseointegrados quando influenciada pelo tipo de material da barra (Liga de Au tipo III, liga de AgPd, liga de CoCr e Ti cp) e por diferentes níveis de desajuste vertical da barra a um dos implantes (5Xm
Publicado em: 2007
-
24. Influence of the pilot hole preparation and screw frequency insertion of the implant on the insertion torque and pulling out resistance / Influência do preparo do orifício piloto e da freqüencia de colocação do implante no seu torque de inserção e resistência ao arrancamento
The aim of the study was to evaluate the influence of the diameter of the pilot hole and the frequency of screw placement on pullout out resistance and insertion torque of the pedicle screw. Pedicle screws of 5, 6 and 7mm of the USS system for vertebral fixation were inserted into wood, polyurethane, polyethylene and bovine bone. The pilot hole for screw ins
Publicado em: 2007