Hot Strength
Mostrando 1-12 de 95 artigos, teses e dissertações.
-
1. Evaluation of the combined addition of aluminum lactate and calcium carbonate to alumina-based castables
Abstract Calcium aluminate cement (CAC) can induce the development of high green mechanical strength to refractory castables in a short period of time (24 h). However, the production of this hydraulic binder is energy-intensive and releases a large content of carbon dioxide (CO2), which adds to global warming. Thus, aiming to develop an alternative binding s
Cerâmica. Publicado em: 2021-06
-
2. The importance of education
Abstract The present research is dedicated to analyzing the addition of sawdust biomass, which is a carbonaceous raw material that may be used in coal blends for the production of metallurgical coke, preserving the required quality, with lower cost. The quality of metallurgical coke may be determined by the efficiency of its chemical, physical and thermal fu
REM, Int. Eng. J.. Publicado em: 2021-06
-
3. Quality evaluation of metallurgical coke produced with sawdust and different mixtures of coal
Abstract The present research is dedicated to analyzing the addition of sawdust biomass, which is a carbonaceous raw material that may be used in coal blends for the production of metallurgical coke, preserving the required quality, with lower cost. The quality of metallurgical coke may be determined by the efficiency of its chemical, physical and thermal fu
REM, Int. Eng. J.. Publicado em: 2021-06
-
4. BIODIESEL SYNTHESIS FROM WASTE COOKING OIL USING A VARIETY OF WASTE MARBLE AS HETEROGENEOUS CATALYSTS
Abstract The research article is based on biodiesel synthesis by the transesterification of waste cooking oil with methanol in the presence of heterogeneous catalysts prepared from different marble. Eight samples of marble were successfully converted into potential catalysts by calcination. The thermal treatment of waste marbles at 300oC-1000oC converted the
Braz. J. Chem. Eng.. Publicado em: 13/01/2020
-
5. Austenitic Grain Size Prediction in Hot Forging of a 20MnCr5 Steel by Numerical Simulation Using the JMAK Model for Industrial Applications
Yield strength and toughness in steels are directly associated with hot forging processes, especially by controlling austenitic grain size and cooling conditions. The phenomenological JMAK model in macroscale has been applied in different material classes to predict grain size after hot forming. However, on an industrial application, there is still a lack of
Mat. Res.. Publicado em: 05/12/2019
-
6. Effect of Ca Content on Properties of Extruded Mg-3Zn-0.5Sr-xCa Alloys for Medical Applications
Mg-3Zn-0.5Sr-xCa(wt.%) (x=0, 0.2, 0.5) alloys were fabricated by casting and hot extrusion. X-ray diffraction (XRD) and optical microscopy observation showed that the microstructure of Mg-3Zn-0.5Sr-xCa alloys was composed of α-Mg matrix and Mg17Sr2 phase precipitated along grain boundaries. The tensile strength of the alloy increased from 255MPa to 305MPa w
Mat. Res.. Publicado em: 30/09/2019
-
7. Microstructural Adjustments and Tensile Properties of a Hot-Forged Ti−22Al−23Nb−3V−Y Alloy
Microstructures and tensile properties of a hot forged Ti−22Al−23Nb−3V−Y alloy were investigated systematically. Different heat treatments were performed to adjust the wrought microstructure to optimize tensile properties. It was found that features of O phase precipitates and its volume fraction was rather sensitive to the cooling rate after the sol
Mat. Res.. Publicado em: 19/08/2019
-
8. Efeito da temperatura de sinterização e da adição de fibras poliméricas em cerâmica porosa obtida a partir de resíduos do processo Kraft
Resumo O processo Kraft gera resíduos que podem ser aplicados em diversos processos produtivos, substituindo matérias-primas comerciais, como lama de cal e areia, ricos em carbonato de cálcio e sílica, respectivamente. Neste trabalho foi realizado um estudo para obtenção de cerâmicas porosas a partir da valorização desses resíduos, utilizando-se fi
Cerâmica. Publicado em: 15/08/2019
-
9. The influence of fiber size on the behavior of the araucaria pine nut shell/PU composite
Abstract The use of araucaria pine nut shell in polymer composites may increase the pine nut value and help protec araucaria (Araucaria angustifolia) itself, which is an endangered species. The aim of this work is to study the influence of the size of pine nut shell fiber on the mechanical properties of composites made of this shell and polyurethane derived
Polímeros. Publicado em: 10/06/2019
-
10. BEAK TRIMMING BY INFRARED RADIATION OF LAYERS
ABSTRACT This study aimed at evaluating beak-trimming methods and intensities on the performance, beak length and uniformity, and egg parameters of commercial layers. During the rearing period, birds were distributed in randomized blocks, with a 2x3 factorial design + two treatments, consisting of beak trimming with infrared (IR) radiation (moderate or sever
Braz. J. Poult. Sci.. Publicado em: 18/04/2019
-
11. THE EFFECT OF BCAA ON ISOMETRIC FORCE FOLLOWING ENDURANCE EXERCISE IN A HOT ENVIRONMENT
RESUMO Introdução: A fadiga decorrente de um exercício de endurance ocorre devido a alterações tanto periféricas quanto centrais e pode influenciar no desempenho subsequente durante um teste de força. Sabe-se que o aumento da concentração de serotonina é um dos fatores centrais associados à fadiga induzida pelo exercício de endurance, principalm
Rev Bras Med Esporte. Publicado em: 2019-02
-
12. Characterization of hibiscus sabdariffa fiber as potential reinforcement for denture acrylic resins
ABSTRACT This study aimed to determine the characteristics of Hibiscus sabdariffa as a fiber-reinforcement material for denture acrylic resins. The Hibiscus sabdariffa fiber was extracted by hot water retting. The fiber was treated at room temperature in aqueous solution of NaOH for 8 hours at 8% concentration. Micrometre gauge and Field emission scanning el
Matéria (Rio J.). Publicado em: 06/12/2018