Hollow Cylinder
Mostrando 1-12 de 20 artigos, teses e dissertações.
-
1. 3D numerical investigation of mixture formation and combustion in a DISI engine at part-load under stratified operation
This work investigates through numerical simulation, the operation of a big bore direct fuel injection spark ignition engine, at part load under stratified operation. It evaluates fuel-air mixture preparation and combustion process with the adoption of detailed chemical kinetics mechanisms for both Isooctane and Ethanol, and applying adaptive mesh refinement
IBICT - Instituto Brasileiro de Informação em Ciência e Tecnologia. Publicado em: 2020
-
2. Influence of the Micromechanics Models and Volume Fraction Distribution on the Overall Behavior of SiC/Al Functionally Graded Pressurized Cylinders
Abstract The assessment of the differences in results obtained from various micromechanics homogenization schemes, as well as the implications of assuming different volume fraction profiles was carried out in the present work. The functionally graded composite chosen for the analysis was Al-SiC and comparisons were made in terms of stress and strain distribu
Lat. Am. j. solids struct.. Publicado em: 08/04/2019
-
3. Behaviour of hollow circular section with multiple perforations under compression, flexure and torsion
Abstract Effect of the presence of perforations on thin structure has been extensively investigated for decades. Various perforation parameters were investigated in past studies. However, study on thin cylinder with multiple perforations has not been carried out. In searching for lighter structural members, the concept of perforated hollow section has been i
Lat. Am. j. solids struct.. Publicado em: 14/03/2019
-
4. On the stability of internally pressurized thick-walled spherical and cylindrical shells made of functionally graded incompressible hyperelastic material
Abstract In this paper, stability analysis of thick-walled spherical and cylindrical shells made of functionally graded incompressible hyperelastic material subjected to internal pressure is presented. Instability point happens in the inflation of above mentioned shells and in this paper effect of material inhomogeneity and shell thickness has been investig
Lat. Am. j. solids struct.. Publicado em: 04/06/2018
-
5. An Analytical Time Domain Solution for the Forced Vibration Analysis of Thick-Walled Cylinders
Abstract In this paper, we propose a time domain analytical solution for the forced vibration analysis of thick-walled hollow cylinders in presence of polar orthotropy. In this regard, solution of the governing equation is decomposed into two parts. The role of the first one is to satisfy boundary conditions utilizing the method of separation of variables be
Lat. Am. j. solids struct.. Publicado em: 2017-09
-
6. Transient Stress Intensity Factors of Functionally Graded Hollow Cylinders with Internal Circumferential Cracks
Abstract In this paper, transient thermomechanical stress intensity factors for functionally graded cylinders with complete internal circumferential cracks are obtained using the weight function method. The finite difference method is used to calculate the time dependent temperature distribution and thermal stresses along the cylinder thickness. Furthermore,
Lat. Am. j. solids struct.. Publicado em: 2016-09
-
7. Three dimensional Free Vibration and Transient Analysis of Two Directional Functionally Graded Thick Cylindrical Panels Under Impact Loading
AbstractIn this paper three dimensional free vibration and transient response of a cylindrical panel made of two directional functionally graded materials (2D-FGMs) based on three dimensional equations of elasticity and subjected to internal impact loading is considered. Material properties vary through both radial and axial directions continuously. The 3D g
Lat. Am. j. solids struct.. Publicado em: 2015-04
-
8. Progressive deformation behaviour of thin cylindrical shell under cyclic temperature variation using Combined Hardening Chaboche Model
This study intends to evaluate thermal ratchetting deformation due to cyclic thermal loading along the axis of a smooth cylindrical shell. Two cases of progressive deformation behaviour are discussed for different loading methods. The aim of the first case is to recognize the shakedown behaviour of the cylinder under applied loading cycles. Alternatively, se
Lat. Am. j. solids struct.. Publicado em: 2014-11
-
9. Estudo teórico experimental da dinâmica de temperatura no interior de uma cavidade cilíndrica. / EXPERIMENTAL THEORETICAL STUDY OF DYNAMIC TEMPERATURE AT A CYLINDRICAL
Two methods for solving a direct heat diffusion problem inside a cylindrical enclosure are proposed, each one is applied with a linear and plus a non-linear solution. Besides, a experimental apparatus was developed for theoretical models validation purpose. Furthermore, as an application of the proposed system the inverse analysis (inverse problem) is used t
Publicado em: 2010
-
10. Desenvolvimento de um equipamento Hollow Cylinder Torsional para solos
A maior parte das solicitações que ocorrem em campo, devidas a obras geotécnicas, está associada à rotação das tensões principais no interior do solo. Muitos equipamentos de ensaios de laboratório tentam simular estas condições, mas o único que possibilita o controle da magnitude e da direção das tensões principais é o equipamento hollow cyli
Publicado em: 2009
-
11. Comportamento geotécnico de um solo coluvionar de São Vendelino (RS) / Geotechnical behavior of a colluvium soil from São Vendelino (RS, Brazil)
Nesta tese foram executados diversos ensaios geotécnicos em um solo coluvionar de uma encosta em que ocorreu uma ruptura translacional, seguida de liquefação e corrida de detritos, em São Vendelino (RS). Na mesma área ocorreram dezenas de rupturas de taludes em dezembro de 2000, durante um evento pluviométrico com chuvas de 148 mm medidas em 2 h. Os ta
Publicado em: 2008
-
12. LINEAR ULTRASONIC MOTOR WITH TUBULAR GEOMETRY / MOTOR ULTRA-SÔNICO LINEAR COM GEOMETRIA TUBULAR
This work presents the study on a linear ultrasonic motor with tubular geometry for linear displacements. Similar topologies, reported elsewhere, are conceived for producing rotary motions. Due to some particular characteristics of this geometry, not explored yet, a new study on interaction between resonance modes in a hollow cylinder for linear movement gen
Publicado em: 2008