Halogen Light
Mostrando 1-12 de 99 artigos, teses e dissertações.
-
1. Household Infrared Technology as an Energy-Efficient Approach to Achieve C-Cπ Bond Construction Reactions
We examined the ability of short-wave infrared (IR) light in the λ1.5-3.0 μm region of the infrared emission spectrum to accomplish C-Cπ bond construction reaction between π-excessive azaheteroaromatic and different carbonyl substrates supported on a bentonitic clay catalyst in solventless condition via a three-component condensation reaction. Preliminar
Journal of the Brazilian Chemical Society. Publicado em: 2022
-
2. Decomposition Rate, pH, and Enamel Color Alteration of At-Home and In-Office Bleaching Agents
Resumo Este estudo avaliou a taxa de decomposição (DR), pH, alteração da cor do esmalte (∆E) e índice de clareamento (DWI) promovido por agentes clareadores caseiros e de consultório. A superfície do esmalte foi submetida a (n=10): agentes caseiros (10%, 15%, 20% de peróxido de carbamida - CP e 6% de peróxido de hidrogênio - HP) e três agentes a
Braz. Dent. J.. Publicado em: 22/07/2019
-
3. Bond strength and marginal microleakage in restorations photopolymerized with LED and halogen light associated with three application modes of a universal adhesive system: in vitro study
RESUMO Objetivo: Avaliar a resistência de união e microinfiltração marginal em restaurações de resina composta, utilizando sistema adesivo Single Bond Universal associado com fotoativadores Ultralux (halógeno) e Bluephase (LED). Métodos: Para resistência de união, oitenta terceiros molares humanos hígidos foram divididos: Halógena (n=40); LED (
RGO, Rev. Gaúch. Odontol.. Publicado em: 13/06/2019
-
4. Evaluation of phenyl-propanedione on yellowing and chemical-mechanical properties of experimental dental resin-based materials
ABSTRACT Objective To evaluate the influence of phenyl-propanedione on yellowing and chemical-mechanical properties of experimental resin-based materials photoactivated using different light curing units (LCUs). Material and Methods Experimental resin-based materials with the same organic matrix (60:40 wt% BisGMA:TEGDMA) were mechanically blended using a
J. Appl. Oral Sci.. Publicado em: 2016-12
-
5. Evaluation of temperature increase during in-office bleaching
ABSTRACT The use of light sources in the bleaching process reduces the time required and promotes satisfactory results. However, these light sources can cause an increase in the pulp temperature. Objective The purpose of the present study was to measure the increase in intrapulpal temperature induced by different light-activated bleaching procedures with a
J. Appl. Oral Sci.. Publicado em: 2016-04
-
6. LED and Halogen Light Transmission through a CAD/CAM Lithium Disilicate Glass-Ceramic
Resumo Avaliou-se o efeito da espessura, cor e translucidez de uma cerâmica vítrea a base de dissilicato de lítio para CAD / CAM sobre a transmissão da luz de unidades de diodos emissores de luz (LED) e de quartzo-tungstênio-halogênio (QTH). Cerâmica IPS e.max CAD nas cores A1, A2, A3, A3.5 de translucidez alta (HT) e baixa (LT) foram cortadas (1, 2,
Braz. Dent. J.. Publicado em: 2015-12
-
7. Anodization growth of self-organized ZrO2 nanotubes on zircaloy-4. Evaluation of the photocatalytic activity
ABSTRACTZrO2nanotube arrays were prepared through anodic oxidation in glycerol organic electrolyte containing ammonium fluoride. The morphology of these nanotube arrays can be controlled by changing the preparation parameters such as applied voltage, fluoride ion concentration and time of anodization. While the oxidation voltage is the main factor that contr
Matéria (Rio J.). Publicado em: 2015-09
-
8. Changes in irradiance and energy density in relation to different curing distances
The present study aimed to assess the influence of curing distance on the loss of irradiance and power density of four curing light devices. The behavior in terms of power density of four different dental curing devices was analyzed (Valo, Elipar 2, Radii-Cal, and Optilux-401) using three different distances of photopolymerization (0 mm, 4 mm, and 8 mm). All
Braz. oral res.. Publicado em: 2015
-
9. Study and characterization of indium oxynitride photoconductors
Multifunctional materials are a new class of thin films and coatings. These materials show interesting characteristics for application in many scientific areas, in special electronic and photonic technologies. These characteristics include sensitivity for thermal, light, mechanical, chemical and other influences, high resistivity, high electrical isolation a
Mat. Res.. Publicado em: 03/12/2013
-
10. Anterior composite restorations in clinical practice: findings from a survey with general dental practitioners
Objectives: The aim of this study was to assess technical preferences of general dental practitioners when restoring anterior composite restorations. How the level of clinical experience or post-graduate training infuenced their options was also tested. Material and Methods: A cross-sectional study was performed using a questionnaire with general denta
J. Appl. Oral Sci.. Publicado em: 2013-12
-
11. Effects of cement-curing mode and light-curing unit on the bond durability of ceramic cemented to dentin
The aim of this study was to evaluate the effects of different light-curing units and resin cement curing types on the bond durability of a feldspathic ceramic bonded to dentin. The crowns of 40 human molars were sectioned, exposing the dentin. Forty ceramic blocks of VITA VM7 were produced according to the manufacturer's recommendations. The ceramic surface
Braz. oral res.. Publicado em: 01/03/2013
-
12. Influence of photo-activation source on enamel demineralization around restorative materials
This study evaluated the effects of the photoactivation source and restorative material on the development of caries-like lesions on human enamel after an in vitro pH challenge. Enamel cavities were prepared in 36 blocks, which were assigned to two groups according to the restorative material: resin-modified glass ionomer (RMGI) and composite resin (CR). Sam
Braz. oral res.. Publicado em: 01/03/2013